There is a 120ms delay implemented for allowing the XHCI host controller to
detect a U3 wakeup pulse. The intention is to wait for the device to retry
the wakeup event if the USB3 PORTSC doesn't reflect the RESUME link status
by the time it is checked. As per the USB3 specification:
tU3WakeupRetryDelay ("Table 7-12. LTSSM State Transition Timeouts")
This would allow the XHCI resume sequence to determine if the root hub
needs to be also resumed. However, in case there is no device connected,
or if there is only a HSUSB device connected, this delay would still affect
the overall resume timing.
Since this delay is solely for detecting U3 wake events (USB3 specific)
then ignore this delay for the disconnected case and the HSUSB connected
only case.
[skip helper function, rename usb3_connected variable -Mathias ]
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231019102924.2797346-20-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If this driver enables the xHC clocks while resuming from sleep, it calls
clk_prepare_enable() without checking for errors and blithely goes on to
read/write the xHC's registers -- which, with the xHC not being clocked,
at least on ARM32 usually causes an imprecise external abort exceptions
which cause kernel oops. Currently, the chips for which the driver does
the clock dance on suspend/resume seem to be the Broadcom STB SoCs, based
on ARM32 CPUs, as it seems...
Found by Linux Verification Center (linuxtesting.org) with the Svace static
analysis tool.
Fixes: 8bd954c561 ("usb: host: xhci-plat: suspend and resume clocks")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231019102924.2797346-19-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In some situations where xhci removal happens parallel to xhci_handshake,
we encounter a scenario where the xhci_handshake can't succeed, and it
polls until timeout.
If xhci_handshake runs until timeout it can on some platforms result in
a long wait which might lead to a watchdog timeout.
Add a helper that checks xhci status during the handshake, and exits if
set state is entered. Use this helper in places where xhci_handshake is
called unlocked and has a long timeout. For example xhci command timeout
and xhci reset.
[commit message and code comment rewording -Mathias]
Signed-off-by: Udipto Goswami <quic_ugoswami@quicinc.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231019102924.2797346-18-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current function that both removes and frees an interrupter isn't
optimal when using several interrupters. The array of interrupters need
to be protected with a lock while removing interrupters, but the default
xhci spin lock can't be used while freeing the interrupters event ring
segment table as dma_free_coherent() should be called with IRQs enabled.
There is no need to free the interrupter under the lock, so split this
code into separate unlocked free part, and a lock protected remove part.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231019102924.2797346-17-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the low-power states of the underlying platform to enable runtime PM.
If the platform doesn't support runtime D3, then enabling default RPM will
result in the controller malfunctioning, as in the case of hotplug devices
not being detected because of a failed interrupt generation.
Cc: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231019102924.2797346-16-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The AMD USB host controller (1022:43f7) isn't going into PCI D3 by default
without anything connected. This is because the policy that was introduced
by commit a611bf473d ("xhci-pci: Set runtime PM as default policy on all
xHC 1.2 or later devices") only covered 1.2 or later.
The 1.1 specification also has the same requirement as the 1.2
specification for D3 support. So expand the runtime PM as default policy
to all AMD 1.1 devices as well.
Fixes: a611bf473d ("xhci-pci: Set runtime PM as default policy on all xHC 1.2 or later devices")
Link: https://composter.com.ua/documents/xHCI_Specification_for_USB.pdf
Co-developed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231019102924.2797346-15-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Increase the event ring dequeue pointer for port change events in the
same way as other event types. No need to handle it separately.
This only touches the driver side tracking of event ring dequeue.
Note: this does move forward the event ring dequeue increase for port
change events a bit.
Previously the dequeue was increased before temporarily dropping
the xhci lock while kicking roothub polling.
Now dequeue is increased after re-aquiring the lock.
This should not matter as event ring dequeue is not touched at all by
hub thread. It's only touched in xhci interrupt handler.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231019102924.2797346-14-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No matter what type of event we receive we want to increase the event
ring dequeue pointer one step for every event that is handled.
For unknown reasons the event ring dequeue increase is done inside the
transfer event handler and port event handler.
As the transfer event handler got more complex and can now loop through
several transfer TRBs on a transfer ring, there were additinal checks
added to avoid increasing event ring dequeue more than one step.
No need for elaborate checks to avoid increasing event ring dequeue
in case the transfer event handler goes through a loop.
Just increasing the event ring dequeue outside the transfer event
handler.
End goal is to increase event ring dequeue in just one place.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231019102924.2797346-13-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci_alloc_erst() has global scope even though it's only used in
xhci-mem.c. Declare it static.
xhci_free_erst() was removed by commit b17a57f89f ("xhci: Refactor
interrupter code for initial multi interrupter support."), but a
declaration in xhci.h still remains. Drop it.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231019102924.2797346-12-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit ebd88cf507 ("xhci: Remove unused defines for ERST_SIZE and
ERST_ENTRIES") removed the ERST_SIZE macro but retained a code comment
explaining the quantity chosen in the macro.
Remove the code comment as well.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231019102924.2797346-11-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mathias notes that the ERST_PTR_MASK macro is named as if it's masking
the Event Ring Dequeue Pointer in the ERDP register, but in actuality
it's masking the inverse.
Invert the macro's value for clarity.
Migrate it to the modern GENMASK_ULL() syntax to avoid u64 casts.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231019102924.2797346-10-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ring segments have just been amended with a monotonically increasing
number.
To allow developers to inspect the segment numbers and ensure
correctness in particular after ring expansion, expose them in each
ring's "trbs" file in debugfs.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231019102924.2797346-9-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When expanding a ring at its "end", ring->last_seg needs to be updated
for Event Rings as well, not just for all the other ring types.
This is not a fix because ring expansion currently isn't done on the
Event Ring. It's just in preparation for when it's added.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231019102924.2797346-8-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Initial xhci_ring allocation has just been amended to assign a
monotonically increasing number to each ring segment.
However rings may be expanded after initial allocation.
So number newly inserted segments starting from the preceding segment in
the ring and renumber all segments succeeding the newly inserted ones.
This is not a fix because ring expansion currently isn't done on the
Event Ring and that's the only ring type using the segment number.
It's just in preparation for when either Event Ring expansion is added
or when other ring types start making use of the segment number.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231019102924.2797346-7-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Users have reported log spam created by "Event Ring Full" xHC event
TRBs. These are caused by interrupt latency in conjunction with a very
busy set of devices on the bus. The errors are benign, but throughput
will suffer as the xHC will pause processing of transfers until the
Event Ring is drained by the kernel.
Commit dc0ffbea57 ("usb: host: xhci: update event ring dequeue pointer
on purpose") mitigated the issue by advancing the Event Ring Dequeue
Pointer already after half a segment has been processed. Nevertheless,
providing a larger Event Ring would be useful to cope with load peaks.
Expand the number of event TRB slots available by increasing the number
of Event Ring segments in the ERST.
Controllers have a hardware-defined limit as to the number of ERST
entries they can process, but with up to 32k it can be excessively high
(sec 5.3.4). So cap the actual number at 2 (configurable through the
ERST_MAX_SEGS macro), which seems like a reasonable quantity. It is
supported by any xHC because the limit in the HCSPARAMS2 register is
defined as a power of 2. Renesas uPD720201 and VIA VL805 controllers
do not support more than 2 ERST entries.
An alternative to increasing the number of Event Ring segments would be
an increase of the segment size. But that requires allocating multiple
contiguous pages, which may be impossible if memory is fragmented.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231019102924.2797346-6-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When using more than one Event Ring segment (ERSTSZ > 1), software shall
set the DESI bits in the ERDP register to the number of the segment to
which the upper ERDP bits are pointing. The xHC may use the DESI bits
as a shortcut to determine whether it needs to check for an Event Ring
Full condition: If it's enqueueing events in a different segment, it
need not compare its internal Enqueue Pointer with the Dequeue Pointer
in the upper bits of the ERDP register (sec 5.5.2.3.3).
Not setting the DESI bits correctly can result in the xHC enqueueing
events past the Dequeue Pointer. On Renesas uPD720201 host controllers,
incorrect DESI bits cause an interrupt storm. For comparison, VIA VL805
host controllers do not exhibit such problems. Perhaps they do not take
advantage of the optimization afforded by the DESI bits.
To fix the issue, assign the segment number to each struct xhci_segment
in xhci_segment_alloc(). When advancing the Dequeue Pointer in
xhci_update_erst_dequeue(), write the segment number to the DESI bits.
On driver probe, set the DESI bits to zero in xhci_set_hc_event_deq() as
processing starts in segment 0. Likewise on driver teardown, clear the
DESI bits to zero in xhci_free_interrupter() when clearing the upper
bits of the ERDP register. Previously those functions (incorrectly)
treated the DESI bits as if they're declared RsvdP.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231019102924.2797346-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The next_trb() helper relies on a link TRB at the end of a ring segment
to know a segment ends. This works well with transfer rings that use
link trbs, but not with event rings.
Event rings segments are always filled by host to segment size
before moving to next segment. It does not use link TRBs
Check for both link trb and full segment in next_trb() helper to
support event rings.
Useful if several interrupters with several event rings are supported.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231019102924.2797346-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With several xhci controllers active at the same time its hard to
keep track of ports without knowing bus number
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231019102924.2797346-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We want to trace other port structure members than just port number
so pass entire port structure as parameter instead of just port number.
Dig the port number from the port structure.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231019102924.2797346-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Prepare for the coming implementation by GCC and Clang of the __counted_by
attribute. Flexible array members annotated with __counted_by can have
their accesses bounds-checked at run-time checking via CONFIG_UBSAN_BOUNDS
(for array indexing) and CONFIG_FORTIFY_SOURCE (for strcpy/memcpy-family
functions).
As found with Coccinelle[1], add __counted_by for struct urb_priv.
[1] https://github.com/kees/kernel-tools/blob/trunk/coccinelle/examples/counted_by.cocci
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Mathias Nyman <mathias.nyman@intel.com>
Cc: linux-usb@vger.kernel.org
Link: https://lore.kernel.org/r/20230915195812.never.371-kees@kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
xhci_add_interrupter() erroneously preserves only the lowest 4 bits when
writing the ERSTBA register, not the lowest 6 bits. Fix it.
Migrate the ERST_BASE_RSVDP macro to the modern GENMASK_ULL() syntax to
avoid a u64 cast.
This was previously fixed by commit 8c1cbec9db ("xhci: fix event ring
segment table related masks and variables in header"), but immediately
undone by commit b17a57f89f ("xhci: Refactor interrupter code for
initial multi interrupter support.").
Fixes: b17a57f89f ("xhci: Refactor interrupter code for initial multi interrupter support.")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v6.3+
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230915143108.1532163-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Event Handler Busy bit shall be cleared by software when the Event
Ring is empty. The xHC is thereby informed that it may raise another
interrupt once it has enqueued new events (sec 4.17.2).
However since commit dc0ffbea57 ("usb: host: xhci: update event ring
dequeue pointer on purpose"), the EHB bit is already cleared after half
a segment has been processed.
As a result, spurious interrupts may occur:
- xhci_irq() processes half a segment, clears EHB, continues processing
remaining events.
- xHC enqueues new events. Because EHB has been cleared, xHC sets
Interrupt Pending bit. Interrupt moderation countdown begins.
- Meanwhile xhci_irq() continues processing events. Interrupt
moderation countdown reaches zero, so an MSI interrupt is signaled.
- xhci_irq() empties the Event Ring, clears EHB again and is done.
- Because an MSI interrupt has been signaled, xhci_irq() is run again.
It discovers there's nothing to do and returns IRQ_NONE.
Avoid by clearing the EHB bit only at the end of xhci_irq().
Fixes: dc0ffbea57 ("usb: host: xhci: update event ring dequeue pointer on purpose")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v5.5+
Cc: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230915143108.1532163-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci-hub.c tracks suspended ports in a suspended_port bitfield.
This is checked when responding to a Get_Status(PORT) request to see if a
port in running U0 state was recently resumed, and adds the required
USB_PORT_STAT_C_SUSPEND change bit in those cases.
The suspended_port bit was left uncleared if a device is disconnected
during suspend. The bit remained set even when a new device was connected
and enumerated. The set bit resulted in a incorrect Get_Status(PORT)
response with a bogus USB_PORT_STAT_C_SUSPEND change
bit set once the new device reached U0 link state.
USB_PORT_STAT_C_SUSPEND change bit is only used for USB2 ports, but
xhci-hub keeps track of both USB2 and USB3 suspended ports.
Cc: stable@vger.kernel.org
Reported-by: Wesley Cheng <quic_wcheng@quicinc.com>
Closes: https://lore.kernel.org/linux-usb/d68aa806-b26a-0e43-42fb-b8067325e967@quicinc.com/
Fixes: 1d5810b692 ("xhci: Rework port suspend structures for limited ports.")
Tested-by: Wesley Cheng <quic_wcheng@quicinc.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230915143108.1532163-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As mentioned in:
commit 474ed23a62 ("xhci: align the last trb before link if it is
easily splittable.")
A bounce buffer is utilized for ensuring that transfers that span across
ring segments are aligned to the EP's max packet size. However, the device
that is used to map the DMA buffer to is currently using the XHCI HCD,
which does not carry any DMA operations in certain configrations.
Migration to using the sysdev entry was introduced for DWC3 based
implementations where the IOMMU operations are present.
Replace the reference to the controller device to sysdev instead. This
allows the bounce buffer to be properly mapped to any implementations that
have an IOMMU involved.
cc: stable@vger.kernel.org
Fixes: 4c39d4b949 ("usb: xhci: use bus->sysdev for DMA configuration")
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230915143108.1532163-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Calculate the IN/OUT budget separately to improve the bandwidth schedule,
meanwhile should avoid Start-Split token overlap between IN and OUT
endpoints, and take into account the FS/LS bandwidth boundary in each
microframe and also in each FS frame.
Calculate the budget for SS of OUT eps and CS of IN eps, but not include
extra-cs, and always add at most extra-cs allowed.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20230830122820.18859-2-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to estimate when fs/ls transactions appear on a downstream bus,
the host must calculate a best case full-speed budget, use a table to
track how many bytes occure in each microframe.
This patch is prepared for introducing an improved bandwidth scheduling.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20230830122820.18859-1-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In a future patch HAS_IOPORT=n will result in inb()/outb() and friends
not being declared. With the AMD quirk handled USB PCI quirks still use
inw() in uhci_check_and_reset_hc() and thus indirectly in
quirk_usb_handoff_uhci(). Handle this by conditionally compiling
uhci_check_and_reset_hc() and stubbing out quirk_usb_handoff_uhci() when
HAS_IOPORT is not available.
Co-developed-by: Arnd Bergmann <arnd@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@kernel.org>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Link: https://lore.kernel.org/r/20230911125653.1393895-4-schnelle@linux.ibm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In a future patch HAS_IOPORT=n will result in inb()/outb() and friends
not being declared. In the pci-quirks case the I/O port acceses are
used in the quirks for several AMD south bridges, Add a config option
for the AMD quirks to depend on HAS_IOPORT and #ifdef the quirk code.
Co-developed-by: Arnd Bergmann <arnd@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@kernel.org>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Link: https://lore.kernel.org/r/20230911125653.1393895-3-schnelle@linux.ibm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A follow on patch will introduce CONFIG_USB_PCI_AMD governing the AMD
quirk and adding its compile time dependency on HAS_IOPORT. In order to
minimize the number of #ifdefs in C files and make that patch easier
to read first group the code together. This is pure code movement
no functional change is intended.
Co-developed-by: Arnd Bergmann <arnd@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@kernel.org>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Link: https://lore.kernel.org/r/20230911125653.1393895-2-schnelle@linux.ibm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DWC3 driver needs access to XHCI Extended Capabilities registers to
read number of usb2 ports and usb3 ports present on multiport controller.
Since the extcaps header is sufficient to parse this info, move port_count
related macros and structure from xhci.h to xhci-ext-caps.h.
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Link: https://lore.kernel.org/r/20230828133033.11988-4-quic_kriskura@quicinc.com
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the big set of tty and serial driver changes for 6.6-rc1.
Lots of cleanups in here this cycle, and some driver updates. Short
summary is:
- Jiri's continued work to make the tty code and apis be a bit more
sane with regards to modern kernel coding style and types
- cpm_uart driver updates
- n_gsm updates and fixes
- meson driver updates
- sc16is7xx driver updates
- 8250 driver updates for different hardware types
- qcom-geni driver fixes
- tegra serial driver change
- stm32 driver updates
- synclink_gt driver cleanups
- tty structure size reduction
All of these have been in linux-next this week with no reported issues.
The last bit of cleanups from Jiri and the tty structure size reduction
came in last week, a bit late but as they were just style changes and
size reductions, I figured they should get into this merge cycle so that
others can work on top of them with no merge conflicts.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZPH+jA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykKyACgldt6QeenTN+6dXIHS/eQHtTKZwMAn3arSeXI
QrUUnLFjOWyoX87tbMBQ
=LVw0
-----END PGP SIGNATURE-----
Merge tag 'tty-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here is the big set of tty and serial driver changes for 6.6-rc1.
Lots of cleanups in here this cycle, and some driver updates. Short
summary is:
- Jiri's continued work to make the tty code and apis be a bit more
sane with regards to modern kernel coding style and types
- cpm_uart driver updates
- n_gsm updates and fixes
- meson driver updates
- sc16is7xx driver updates
- 8250 driver updates for different hardware types
- qcom-geni driver fixes
- tegra serial driver change
- stm32 driver updates
- synclink_gt driver cleanups
- tty structure size reduction
All of these have been in linux-next this week with no reported
issues. The last bit of cleanups from Jiri and the tty structure size
reduction came in last week, a bit late but as they were just style
changes and size reductions, I figured they should get into this merge
cycle so that others can work on top of them with no merge conflicts"
* tag 'tty-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (199 commits)
tty: shrink the size of struct tty_struct by 40 bytes
tty: n_tty: deduplicate copy code in n_tty_receive_buf_real_raw()
tty: n_tty: extract ECHO_OP processing to a separate function
tty: n_tty: unify counts to size_t
tty: n_tty: use u8 for chars and flags
tty: n_tty: simplify chars_in_buffer()
tty: n_tty: remove unsigned char casts from character constants
tty: n_tty: move newline handling to a separate function
tty: n_tty: move canon handling to a separate function
tty: n_tty: use MASK() for masking out size bits
tty: n_tty: make n_tty_data::num_overrun unsigned
tty: n_tty: use time_is_before_jiffies() in n_tty_receive_overrun()
tty: n_tty: use 'num' for writes' counts
tty: n_tty: use output character directly
tty: n_tty: make flow of n_tty_receive_buf_common() a bool
Revert "tty: serial: meson: Add a earlycon for the T7 SoC"
Documentation: devices.txt: Fix minors for ttyCPM*
Documentation: devices.txt: Remove ttySIOC*
Documentation: devices.txt: Remove ttyIOC*
serial: 8250_bcm7271: improve bcm7271 8250 port
...
If initially isoc_count = 0, periodic_count > 0 and the io watchdog is
not started (e.g. just timed out), then the io watchdog may not run after
submitting isoc urbs and enable_periodic(). The isoc urbs may not complete
forever if the controller had already stopped periodic schedule.
This will try to call turn_on_io_watchdog() for each enable_periodic() to
ensure the io watchdog functions properly.
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20230809065327.952368-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The resource is checked in probe function, so there is
no need do this check in remove function.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20230809085348.2761782-1-yangyingliang@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Wireless USB has long been defunct, and kernel support for it was
removed in 2020 by commit caa6772db4 ("Staging: remove wusbcore and
UWB from the kernel tree.").
Nevertheless, some vestiges of the old implementation still clutter up
the USB subsystem and one or two other places. Let's get rid of them
once and for all.
The only parts still left are the user-facing APIs in
include/uapi/linux/usb/ch9.h. (There are also a couple of misleading
instances, such as the Sierra Wireless USB modem, which is a USB modem
made by Sierra Wireless.)
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/b4f2710f-a2de-4fb0-b50f-76776f3a961b@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some NXP processor using chipidea IP has a bug when frame babble is
detected.
As per 4.15.1.1.1 Serial Bus Babble:
A babble condition also exists if IN transaction is in progress at
High-speed SOF2 point. This is called frame babble. The host controller
must disable the port to which the frame babble is detected.
The USB controller has disabled the port (PE cleared) and has asserted
USBERRINT when frame babble is detected, but PEC is not asserted.
Therefore, the SW isn't aware that port has been disabled. Then the
SW keeps sending packets to this port, but all of the transfers will
fail.
This workaround will firstly assert PCD by SW when USBERRINT is detected
and then judge whether port change has really occurred or not by polling
roothub status. Because the PEC doesn't get asserted in our case, this
patch will also assert it by SW when specific conditions are satisfied.
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/20230809024432.535160-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is not possible for platform_get_irq() to return 0. Use the
return value from platform_get_irq().
Signed-off-by: Ruan Jinjie <ruanjinjie@huawei.com>
Reviewed-by: Justin Chen <justin.chen@broadcom.com>
Link: https://lore.kernel.org/r/20230802031236.2272196-1-ruanjinjie@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need the USB fixes in here for testing and for other patches to be
applied on top of.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ohci_hcd_at91_drv_suspend() sets ohci->rh_state to OHCI_RH_HALTED when
suspend which will let the ohci_irq() skip the interrupt after resume. And
nobody to handle this interrupt.
According to the comment in ohci_hcd_at91_drv_suspend(), it need to reset
when resume from suspend(MEM) to fix by setting "hibernated" argument of
ohci_resume().
Signed-off-by: Guiting Shen <aarongt.shen@gmail.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20230728120648.5878-1-aarongt.shen@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Link: https://lore.kernel.org/r/20230726113816.888-30-frank.li@vivo.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20230726113816.888-29-frank.li@vivo.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Link: https://lore.kernel.org/r/20230726113816.888-28-frank.li@vivo.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Link: https://lore.kernel.org/r/20230726113816.888-27-frank.li@vivo.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Link: https://lore.kernel.org/r/20230726113816.888-26-frank.li@vivo.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Link: https://lore.kernel.org/r/20230726113816.888-25-frank.li@vivo.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Link: https://lore.kernel.org/r/20230726113816.888-24-frank.li@vivo.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Link: https://lore.kernel.org/r/20230726113816.888-23-frank.li@vivo.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
