The function ci_usb_phy_init is already handling the
hw_phymode_configure path which is also only possible after we have
a valid phy. So we move the ci_ulpi_init after the phy initialization
to be really sure to be able to communicate with the ulpi phy.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Acked-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/20240328-chipidea-phy-misc-v1-1-907d9de5d4df@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After pulling the reset pin some phys are not immediately ready. We add
a short delay of at least 10 ms to ensure that the phy can be properly
used.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20240402-phy-misc-v1-1-de5c17f93f17@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ChipID bytes are read in inverse order: invert the ChipID value
defined as IT5205FN_CHIP_ID and used for validating the same.
Fixes: 41fe9ea169 ("usb: typec: mux: Add ITE IT5205 Alternate Mode Passive MUX driver")
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20240409113646.305105-1-angelogioacchino.delregno@collabora.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
fsl_ep_queue() is only called by usb_ep_queue() (as ep->ops->queue()).
So _ep isn't NULL.
As ep->ops->queue = fsl_ep_queue, the ep was initialized by
struct_ep_setup() and so ep->udc isn't NULL either.
Drop the check for _ep being NULL and assign udc earlier to prevent
following an uninitialized pointer in the two dev_vdbg()s in lines 878
and 882. This fixes a compiler warning when using clang and
CONFIG_USB_GADGET_VERBOSE=y.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202404050227.TTvcCPBu-lkp@intel.com/
Fixes: 6025f20f16 ("usb: gadget: fsl-udc: Replace custom log wrappers by dev_{err,warn,dbg,vdbg}")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20240405055812.694123-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The incompatible device in my possession has a sticker that says
"F5U002 Rev 2" and "P80453-B", and lsusb identifies it as
"050d:0002 Belkin Components IEEE-1284 Controller". There is a bug
report from 2007 from Michael Trausch who was seeing the exact same
errors that I saw in 2024 trying to use this cable.
Link: https://lore.kernel.org/all/46DE5830.9060401@trausch.us/
Signed-off-by: Alex Henrie <alexhenrie24@gmail.com>
Link: https://lore.kernel.org/r/20240326150723.99939-5-alexhenrie24@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This device is a gray USB parallel port adapter with "F5U002" imprinted
on the plastic and a sticker that says both "F5U002" and "P80453-A".
It's identified in lsusb as "05ab:1001 In-System Design BAYI Printer
Class Support". It's subtly different from the other gray cable I have
that has "F5U002 Rev 2" and "P80453-B" on its sticker and device ID
050d:0002.
The uss720 driver appears to work flawlessly with this device, although
the device evidently does not support ECP.
Signed-off-by: Alex Henrie <alexhenrie24@gmail.com>
Link: https://lore.kernel.org/r/20240326150723.99939-4-alexhenrie24@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This avoids a "fix this legacy no-device port driver" warning from
parport_announce_port in drivers/parport/share.c. The parport driver now
requires a pointer to the device struct.
Signed-off-by: Alex Henrie <alexhenrie24@gmail.com>
Acked-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Link: https://lore.kernel.org/r/20240326150723.99939-2-alexhenrie24@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Dell quirk from ucsi_acpi.c. The quirk is no longer
necessary as we no longer send lone connector change acks.
Signed-off-by: Christian A. Ehrhardt <lk@c--e.de>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240327224554.1772525-4-lk@c--e.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some PPM implementation do not like UCSI_ACK_CONNECTOR_CHANGE
without UCSI_ACK_COMMAND_COMPLETE. Moreover, doing this is racy
as it requires sending two UCSI_ACK_CC_CI commands in a row and
the second one will be started with UCSI_CCI_ACK_COMPLETE already
set in CCI.
Bundle the UCSI_ACK_CONNECTOR_CHANGE with the UCSI_ACK_COMMAND_COMPLETE
for the UCSI_GET_CONNECTOR_STATUS command that is sent while
handling a connector change event.
Signed-off-by: Christian A. Ehrhardt <lk@c--e.de>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240327224554.1772525-3-lk@c--e.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In ucsi.h there are flag definitions for the ->flags field
in struct ucsi. Some implementations abuse these bits for
their private ->flags fields e.g. in struct ucsi_acpi.
Move the definitions into the backend implementations that
still need them. While there fix one instance where the flag
name was not converted in a previous change.
No semantic change intended.
Signed-off-by: Christian A. Ehrhardt <lk@c--e.de>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240327224554.1772525-2-lk@c--e.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation to adding more quirks, extract quirks to the static
variables and reference them through match->data. Otherwise adding
more quirks will add the table really cumbersome.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240329-qcom-ucsi-fixes-v2-8-0f5d37ed04db@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Qualcomm firmware doesn't return sane information for device's PDOs
unless the partner is also using a PD mode. On SC8280XP this even
results in the Error bit being set in the UCSI response (with 0 error
status).
Add a quirk to delay reading USB PD capabilities for a device until we
detect a partner in PD mode.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240329-qcom-ucsi-fixes-v2-7-0f5d37ed04db@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Extract function to read PDOs from the port and set PD capabilities
accordingly.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240329-qcom-ucsi-fixes-v2-6-0f5d37ed04db@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In a way similar to the previous commit, move
typec_partner_set_usb_power_delivery() to be called after reading the PD
caps. This also removes calls to
usb_power_delivery_unregister_capabilities() from the error path. Keep
all capabilities registered until they are cleared by
ucsi_unregister_partner_pdos().
Fixes: b04e1747fb ("usb: typec: ucsi: Register USB Power Delivery Capabilities")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240329-qcom-ucsi-fixes-v2-5-0f5d37ed04db@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
UCSI driver will attempt to set a USB PD device only if it was able to
read PDOs from the firmware. This results in suboptimal behaviour, since
the PD device will be created anyway. Move calls to
typec_port_set_usb_power_delivery() out of conditional code and call it
after reading capabilities.
Fixes: b04e1747fb ("usb: typec: ucsi: Register USB Power Delivery Capabilities")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240329-qcom-ucsi-fixes-v2-4-0f5d37ed04db@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use typec_partner_usb_power_delivery_register() to register PD device
for Type-C partner so that the PD device is nested under the partner's
device in sysfs.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240329-qcom-ucsi-fixes-v2-3-0f5d37ed04db@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reading Partner Source PDOs for the consumer Connectors appears to be
working. Permit getting PDOs in this case in order to populate
capabilities of the connected power supply in the sysfs.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240329-qcom-ucsi-fixes-v2-2-0f5d37ed04db@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The name and description of the USB_NO_PARTNER_PDOS quirk specifies that
only retrieving PDOS of the attached device is crashing. Retrieving PDOS
of the UCSI device works. Fix the condition to limit the workaround only
to is_partner cases.
Fixes: 1d103d6af2 ("usb: typec: ucsi: fix UCSI on buggy Qualcomm devices")
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240329-qcom-ucsi-fixes-v2-1-0f5d37ed04db@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Core in typec_altmode_register_driver() already sets the .owner, so
driver does not need to.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240331091737.19836-3-krzk@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Core in typec_altmode_register_driver() already sets the .owner, so
driver does not need to.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240331091737.19836-2-krzk@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Core in platform_driver_register() already sets the .owner, so driver
does not need to.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240331091737.19836-1-krzk@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The UCSI specification defines some notifications to be optional for the
PPM to support. From these only enable the ones the PPM informs us are
actually supported.
Signed-off-by: Diogo Ivo <diogo.ivo@tecnico.ulisboa.pt>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/yhz7nq622mbg3rqsyvqz632pc756niagpfbnzayfswhzo7esho@vrdtx5c3hjgx
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver_desc variable is only used in some configurations:
drivers/usb/gadget/udc/omap_udc.c:113:19: error: unused variable 'driver_desc' [-Werror,-Wunused-const-variable]
Since there is only ever one user of it, just open-code the string in place
and remove the global variable and the macro behind it. This also helps
grep for the MODULE_DESCRIPTION string.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20240403080702.3509288-26-arnd@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_DRM_AUX_BRIDGE depends on CONFIG_OF but that dependency is not
included when CONFIG_TYPEC_MUX_PTN36502 selects it, resulting in a
Kconfig warning when CONFIG_OF is disabled:
WARNING: unmet direct dependencies detected for DRM_AUX_BRIDGE
Depends on [n]: HAS_IOMEM [=y] && DRM_BRIDGE [=y] && OF [=n]
Selected by [m]:
- TYPEC_MUX_PTN36502 [=m] && USB_SUPPORT [=y] && TYPEC [=m] && I2C [=y] && (DRM [=y] || DRM [=y]=n) && DRM_BRIDGE [=y]
Only select CONFIG_DRM_AUX_BRIDGE when CONFIG_DRM_BRIDGE and CONFIG_OF
are enabled to clear up the warning. This results in no functional
change because prior to the refactoring that introduces this warning,
ptn36502_register_bridge() returned 0 when CONFIG_OF was disabled, which
continues to occur with drm_aux_bridge_register() when
CONFIG_DRM_AUX_BRIDGE is not enabled.
Fixes: 9dc28ea21e ("usb: typec: ptn36502: switch to DRM_AUX_BRIDGE")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Luca Weiss <luca.weiss@fairphone.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20240328-fix-ptn36502-drm_aux_bridge-select-v1-1-85552117e26e@kernel.org
Link: https://lore.kernel.org/r/20240404123534.2708591-1-arnd@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SanDisks USB3 storage may disapper after system reboot:
usb usb2-port3: link state change
xhci_hcd 0000:00:14.0: clear port3 link state change, portsc: 0x2c0
usb usb2-port3: do warm reset, port only
xhci_hcd 0000:00:14.0: xhci_hub_status_data: stopping usb2 port polling
xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x2b0, return 0x2b0
usb usb2-port3: not warm reset yet, waiting 50ms
xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x2f0, return 0x2f0
usb usb2-port3: not warm reset yet, waiting 200ms
...
xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x6802c0, return 0x7002c0
usb usb2-port3: not warm reset yet, waiting 200ms
xhci_hcd 0000:00:14.0: clear port3 reset change, portsc: 0x4802c0
xhci_hcd 0000:00:14.0: clear port3 warm(BH) reset change, portsc: 0x4002c0
xhci_hcd 0000:00:14.0: clear port3 link state change, portsc: 0x2c0
xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x2c0, return 0x2c0
usb usb2-port3: not enabled, trying warm reset again...
This is due to the USB device still cause port change event after xHCI is
shuted down:
xhci_hcd 0000:38:00.0: // Setting command ring address to 0xffffe001
xhci_hcd 0000:38:00.0: xhci_resume: starting usb3 port polling.
xhci_hcd 0000:38:00.0: xhci_hub_status_data: stopping usb4 port polling
xhci_hcd 0000:38:00.0: xhci_hub_status_data: stopping usb3 port polling
xhci_hcd 0000:38:00.0: hcd_pci_runtime_resume: 0
xhci_hcd 0000:38:00.0: xhci_shutdown: stopping usb3 port polling.
xhci_hcd 0000:38:00.0: // Halt the HC
xhci_hcd 0000:38:00.0: xhci_shutdown completed - status = 1
xhci_hcd 0000:00:14.0: xhci_shutdown: stopping usb1 port polling.
xhci_hcd 0000:00:14.0: // Halt the HC
xhci_hcd 0000:00:14.0: xhci_shutdown completed - status = 1
xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x1203, return 0x203
xhci_hcd 0000:00:14.0: set port reset, actual port 2-3 status = 0x1311
xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x201203, return 0x100203
xhci_hcd 0000:00:14.0: clear port3 reset change, portsc: 0x1203
xhci_hcd 0000:00:14.0: clear port3 warm(BH) reset change, portsc: 0x1203
xhci_hcd 0000:00:14.0: clear port3 link state change, portsc: 0x1203
xhci_hcd 0000:00:14.0: clear port3 connect change, portsc: 0x1203
xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x1203, return 0x203
usb 2-3: device not accepting address 2, error -108
xhci_hcd 0000:00:14.0: xHCI dying or halted, can't queue_command
xhci_hcd 0000:00:14.0: Set port 2-3 link state, portsc: 0x1203, write 0x11261
xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x1263, return 0x263
xhci_hcd 0000:00:14.0: set port reset, actual port 2-3 status = 0x1271
xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x12b1, return 0x2b1
usb usb2-port3: not reset yet, waiting 60ms
ACPI: PM: Preparing to enter system sleep state S5
xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x12f1, return 0x2f1
usb usb2-port3: not reset yet, waiting 200ms
reboot: Restarting system
The port change event is caused by LPM transition, so disabling LPM at shutdown
to make sure the device is in U0 for warmboot.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20240305065140.66801-1-kai.heng.feng@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When ncm function is working and then stop usb0 interface for link down,
eth_stop() is called. At this piont, accidentally if usb transport error
should happen in usb_ep_enable(), 'in_ep' and/or 'out_ep' may not be enabled.
After that, ncm_disable() is called to disable for ncm unbind
but gether_disconnect() is never called since 'in_ep' is not enabled.
As the result, ncm object is released in ncm unbind
but 'dev->port_usb' associated to 'ncm->port' is not NULL.
And when ncm bind again to recover netdev, ncm object is reallocated
but usb0 interface is already associated to previous released ncm object.
Therefore, once usb0 interface is up and eth_start_xmit() is called,
released ncm object is dereferrenced and it might cause use-after-free memory.
[function unlink via configfs]
usb0: eth_stop dev->port_usb=ffffff9b179c3200
--> error happens in usb_ep_enable().
NCM: ncm_disable: ncm=ffffff9b179c3200
--> no gether_disconnect() since ncm->port.in_ep->enabled is false.
NCM: ncm_unbind: ncm unbind ncm=ffffff9b179c3200
NCM: ncm_free: ncm free ncm=ffffff9b179c3200 <-- released ncm
[function link via configfs]
NCM: ncm_alloc: ncm alloc ncm=ffffff9ac4f8a000
NCM: ncm_bind: ncm bind ncm=ffffff9ac4f8a000
NCM: ncm_set_alt: ncm=ffffff9ac4f8a000 alt=0
usb0: eth_open dev->port_usb=ffffff9b179c3200 <-- previous released ncm
usb0: eth_start dev->port_usb=ffffff9b179c3200 <--
eth_start_xmit()
--> dev->wrap()
Unable to handle kernel paging request at virtual address dead00000000014f
This patch addresses the issue by checking if 'ncm->netdev' is not NULL at
ncm_disable() to call gether_disconnect() to deassociate 'dev->port_usb'.
It's more reasonable to check 'ncm->netdev' to call gether_connect/disconnect
rather than check 'ncm->port.in_ep->enabled' since it might not be enabled
but the gether connection might be established.
Signed-off-by: Norihiko Hama <Norihiko.Hama@alpsalpine.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20240327023550.51214-1-Norihiko.Hama@alpsalpine.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Off-by-one errors happen because nr_snk_pdo and nr_src_pdo are
incorrectly added one. The index of the loop is equal to the number of
PDOs to be updated when leaving the loop and it doesn't need to be added
one.
When doing the power negotiation, TCPM relies on the "nr_snk_pdo" as
the size of the local sink PDO array to match the Source capabilities
of the partner port. If the off-by-one overflow occurs, a wrong RDO
might be sent and unexpected power transfer might happen such as over
voltage or over current (than expected).
"nr_src_pdo" is used to set the Rp level when the port is in Source
role. It is also the array size of the local Source capabilities when
filling up the buffer which will be sent as the Source PDOs (such as
in Power Negotiation). If the off-by-one overflow occurs, a wrong Rp
level might be set and wrong Source PDOs will be sent to the partner
port. This could potentially cause over current or port resets.
Fixes: cd099cde4e ("usb: typec: tcpm: Support multiple capabilities")
Cc: stable@vger.kernel.org
Signed-off-by: Kyle Tso <kyletso@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240404133517.2707955-1-kyletso@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of bailing when fences have already been installed on the
DMABUF, wait for them (with a timeout) when doing a blocking operation.
This fixes the issue where userspace would submit a DMABUF with fences
already installed, with the (correct) expectation that it would just
work.
Fixes: 7b07a2a7ca ("usb: gadget: functionfs: Add DMABUF import interface")
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20240402110951.16376-3-paul@crapouillou.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A "read" fence was installed when the DMABUF was to be written to,
and a "write" fence was installed when the DMABUF was to be read from.
Besides, dma_resv_usage_rw() should only be used when waiting for
fences.
Fixes: 7b07a2a7ca ("usb: gadget: functionfs: Add DMABUF import interface")
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20240402110951.16376-2-paul@crapouillou.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix issues when initially checking for a connector change:
- Use the correct connector number not the entire CCI.
- Call ->read under the PPM lock.
- Remove a bogus READ_ONCE.
Fixes: 808a8b9e0b ("usb: typec: ucsi: Check for notifications after init")
Cc: stable@kernel.org
Signed-off-by: Christian A. Ehrhardt <lk@c--e.de>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240401210515.1902048-1-lk@c--e.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The pointer from a xhci usb virt device to its root hub port
(vdev->rhub_port) is set later when device is addressed, not while
vdev is allocated.
Tracepoints dereferenced this rhub_port pointer when freeing the virt
device, which causes null pointer dereference if tracing is enabled
and device is freed before addressed.
This can happen if tracing is enabled and xhci driver is unloaded before
a device is fully enumerated, or initial enumeration fails and device
is reset and freed before retry.
Don't dereference the rhub_port or show port numbers when tracing
xhci_free_virt_device(). This info is not very useful anyway.
Print the more useful slot id instead
Fixes: 06790c1908 ("xhci: replace real & fake port with pointer to root hub port")
Reported-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Closes: https://lore.kernel.org/linux-usb/20240402005007.klv2ij727fkz7rpd@synopsys.com/
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240404121106.2842417-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we get STS_HCE we give up on the interrupt, but for the purpose
of IRQ handling that still counts as ours. We may return IRQ_NONE
only if we are positive that it wasn't ours. Hence correct the default.
Fixes: 2a25e66d67 ("xhci: print warning when HCE was set")
Cc: stable@vger.kernel.org # v6.2+
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240404121106.2842417-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The XMOS XVF3500 VocalFusion Voice Processor[1] is a low-latency, 32-bit
multicore controller for voice processing.
This device requires a specific power sequence, which consists of
enabling the regulators that control the 3V3 and 1V0 device supplies,
and a reset de-assertion after a delay of at least 100ns.
Once in normal operation, the XVF3500 registers itself as a USB device,
and it does not require any device-specific operations in the driver.
[1] https://www.xmos.com/xvf3500/
Acked-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Javier Carrasco <javier.carrasco@wolfvision.net>
Link: https://lore.kernel.org/r/20240325-onboard_xvf3500-v8-8-29e3f9222922@wolfvision.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Most of the functionality this driver provides can be used by non-hub
devices as well.
To account for the hub-specific code, add a flag to the device data
structure and check its value for hub-specific code.
The 'always_powered_in_supend' attribute is only available for hub
devices, keeping the driver's default behavior for non-hub devices (keep
on in suspend).
Acked-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Javier Carrasco <javier.carrasco@wolfvision.net>
Link: https://lore.kernel.org/r/20240325-onboard_xvf3500-v8-6-29e3f9222922@wolfvision.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch prepares onboad_hub to support non-hub devices by renaming
the driver files and their content, the headers and their references.
The comments and descriptions have been slightly modified to keep
coherence and account for the specific cases that only affect onboard
hubs (e.g. peer-hub).
The "hub" variables in functions where "dev" (and similar names) variables
already exist have been renamed to onboard_dev for clarity, which adds a
few lines in cases where more than 80 characters are used.
No new functionality has been added.
Acked-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Javier Carrasco <javier.carrasco@wolfvision.net>
Link: https://lore.kernel.org/r/20240325-onboard_xvf3500-v8-2-29e3f9222922@wolfvision.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current implementation uses generic names for the power supplies,
which conflicts with proper name definitions in the device bindings.
Add a per-device property to include real supply names and keep generic
names for existing devices to keep backward compatibility.
Acked-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Javier Carrasco <javier.carrasco@wolfvision.net>
Link: https://lore.kernel.org/r/20240325-onboard_xvf3500-v8-1-29e3f9222922@wolfvision.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dt-bindings is going to use "usb_wakeup" as wakup clock name. This will
align the change with dt-bindings.
Acked-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://lore.kernel.org/r/20240321081439.541799-11-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the trailing comma in the terminator entry for the OF table
making code robust against (theoretical) misrebases or other similar
things where the new entry goes _after_ the termination without the
compiler noticing.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20240319105356.87287-6-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The RZ/G2L family SoCs has 10 pipe buffers compared to 16 pipe buffers on
RZ/A2M. Update the pipe configuration for RZ/G2L family SoCs and use
family SoC specific compatible to handle this difference.
The pipe configuration of RZ/G2L is same as usbhsc_rzg2l_default_pipe[],
so select the default pipe configuration for RZ/G2L SoCs by setting
.has_new_pipe_configs to zero.
Add SoC specific compatible to OF table to avoid ABI breakage with old
DTB. To optimize memory usage the SoC specific compatible will be removed
later.
Based on the patch in BSP by Huy Nguyen <huy.nguyen.wh@renesas.com>
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20240319105356.87287-5-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As per the hardware manual, double buffer setting results in fewer
interrupts for high-speed data transfers. Improve usbhsc_default_pipe[]
for isochronous transfers by updating the table from single->double
buffering and update the pipe number accordingly.
Suggested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20240319105356.87287-4-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The show and store callback routines for the "disable" sysfs attribute
file in port.c acquire the device lock for the port's parent hub
device. This can cause problems if another process has locked the hub
to remove it or change its configuration:
Removing the hub or changing its configuration requires the
hub interface to be removed, which requires the port device
to be removed, and device_del() waits until all outstanding
sysfs attribute callbacks for the ports have returned. The
lock can't be released until then.
But the disable_show() or disable_store() routine can't return
until after it has acquired the lock.
The resulting deadlock can be avoided by calling
sysfs_break_active_protection(). This will cause the sysfs core not
to wait for the attribute's callback routine to return, allowing the
removal to proceed. The disadvantage is that after making this call,
there is no guarantee that the hub structure won't be deallocated at
any moment. To prevent this, we have to acquire a reference to it
first by calling hub_get().
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/f7a8c135-a495-4ce6-bd49-405a45e7ea9a@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Create hub_get() and hub_put() routines to encapsulate the kref_get()
and kref_put() calls in hub.c. The new routines will be used by the
next patch in this series.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/604da420-ae8a-4a9e-91a4-2d511ff404fb@rowland.harvard.edu
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Check the UCSI_CAP_GET_PD_MESSAGE bit before sending GET_PD_MESSAGE to
discover partner and cable identity, check UCSI_CAP_CABLE_DETAILS before
sending GET_CABLE_PROPERTY to discover the cable and check
UCSI_CAP_ALT_MODE_DETAILS before registering the a cable plug. Additionally,
move 8 bits from reserved_1 to features in the ucsi_capability struct. This
makes the field 16 bits, still 8 short of the 24 bits allocated for it in
UCSI v3.0, but it will not overflow because UCSI only defines 14 bits in
bmOptionalFeatures.
Fixes: 38ca416597 ("usb: typec: ucsi: Register cables based on GET_CABLE_PROPERTY")
Link: https://lore.kernel.org/linux-usb/44e8142f-d9b3-487b-83fe-39deadddb492@linaro.org
Suggested-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Jameson Thies <jthies@google.com>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Reviewed-by: Benson Leung <bleung@chromium.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240315171836.343830-2-jthies@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Check the UCSI_CCI_RESET_COMPLETE complete flag before starting
another reset. Use a UCSI_SET_NOTIFICATION_ENABLE command to clear
the flag if it is set.
Signed-off-by: Christian A. Ehrhardt <lk@c--e.de>
Cc: stable <stable@kernel.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Link: https://lore.kernel.org/r/20240320073927.1641788-6-lk@c--e.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
