The VEB (virtual embedded switch) as a switch element can be
connected according datasheet though its uplink to:
- Physical port
- Port Virtualizer (not used directly by i40e driver but can
be present in MFP mode where the physical port is shared
between PFs)
- No uplink (aka floating VEB)
But VEB uplink cannot be connected to another VEB and any attempt
to do so results in:
"i40e 0000:02:00.0: couldn't add VEB, err -EIO aq_err I40E_AQ_RC_ENOENT"
that indicates "the uplink SEID does not point to valid element".
Remove this logic from the driver code this way:
1) For debugfs only allow to build floating VEB (uplink_seid == 0)
or main VEB (uplink_seid == mac_seid)
2) Do not recurse in i40e_veb_link_event() as no VEB cannot have
sub-VEBs
3) Ditto for i40e_veb_rebuild() + simplify the function as we know
that the VEB for rebuild can be only the main LAN VEB or some
of the floating VEBs
4) In i40e_rebuild() there is no need to check veb->uplink_seid
as the possible ones are 0 and MAC SEID
5) In i40e_vsi_release() do not take into account VEBs whose
uplink is another VEB as this is not possible
6) Remove veb_idx field from i40e_veb as a VEB cannot have
sub-VEBs
Tested using i40e debugfs interface:
1) Initial state
[root@cnb-03 net-next]# CMD="/sys/kernel/debug/i40e/0000:02:00.0/command"
[root@cnb-03 net-next]# echo dump switch > $CMD
[root@cnb-03 net-next]# dmesg -c
[ 98.440641] i40e 0000:02:00.0: header: 3 reported 3 total
[ 98.446053] i40e 0000:02:00.0: type=19 seid=392 uplink=160 downlink=16
[ 98.452593] i40e 0000:02:00.0: type=17 seid=160 uplink=2 downlink=0
[ 98.458856] i40e 0000:02:00.0: type=19 seid=390 uplink=160 downlink=16
2) Add floating VEB
[root@cnb-03 net-next]# echo add relay > $CMD
[root@cnb-03 net-next]# dmesg -c
[ 122.745630] i40e 0000:02:00.0: added relay 162
[root@cnb-03 net-next]# echo dump switch > $CMD
[root@cnb-03 net-next]# dmesg -c
[ 136.650049] i40e 0000:02:00.0: header: 4 reported 4 total
[ 136.655466] i40e 0000:02:00.0: type=19 seid=392 uplink=160 downlink=16
[ 136.661994] i40e 0000:02:00.0: type=17 seid=160 uplink=2 downlink=0
[ 136.668264] i40e 0000:02:00.0: type=19 seid=390 uplink=160 downlink=16
[ 136.674787] i40e 0000:02:00.0: type=17 seid=162 uplink=0 downlink=0
3) Add VMDQ2 VSI to this new VEB
[root@cnb-03 net-next]# dmesg -c
[ 168.351763] i40e 0000:02:00.0: added VSI 394 to relay 162
[ 168.374652] enp2s0f0np0v0: NIC Link is Up, 40 Gbps Full Duplex, Flow Control: None
[root@cnb-03 net-next]# echo dump switch > $CMD
[root@cnb-03 net-next]# dmesg -c
[ 195.683204] i40e 0000:02:00.0: header: 5 reported 5 total
[ 195.688611] i40e 0000:02:00.0: type=19 seid=394 uplink=162 downlink=16
[ 195.695143] i40e 0000:02:00.0: type=17 seid=162 uplink=0 downlink=0
[ 195.701410] i40e 0000:02:00.0: type=19 seid=392 uplink=160 downlink=16
[ 195.707935] i40e 0000:02:00.0: type=17 seid=160 uplink=2 downlink=0
[ 195.714201] i40e 0000:02:00.0: type=19 seid=390 uplink=160 downlink=16
4) Try to delete the VEB
[root@cnb-03 net-next]# echo del relay 162 > $CMD
[root@cnb-03 net-next]# dmesg -c
[ 239.260901] i40e 0000:02:00.0: deleting relay 162
[ 239.265621] i40e 0000:02:00.0: can't remove VEB 162 with 1 VSIs left
5) Do PF reset and check switch status after rebuild
[root@cnb-03 net-next]# echo pfr > $CMD
[root@cnb-03 net-next]# echo dump switch > $CMD
[root@cnb-03 net-next]# dmesg -c
...
[ 272.333655] i40e 0000:02:00.0: header: 5 reported 5 total
[ 272.339066] i40e 0000:02:00.0: type=19 seid=394 uplink=162 downlink=16
[ 272.345599] i40e 0000:02:00.0: type=17 seid=162 uplink=0 downlink=0
[ 272.351862] i40e 0000:02:00.0: type=19 seid=392 uplink=160 downlink=16
[ 272.358387] i40e 0000:02:00.0: type=17 seid=160 uplink=2 downlink=0
[ 272.364654] i40e 0000:02:00.0: type=19 seid=390 uplink=160 downlink=16
6) Delete VSI and delete VEB
[ 297.199116] i40e 0000:02:00.0: deleting VSI 394
[ 299.807580] i40e 0000:02:00.0: deleting relay 162
[ 309.767905] i40e 0000:02:00.0: header: 3 reported 3 total
[ 309.773318] i40e 0000:02:00.0: type=19 seid=392 uplink=160 downlink=16
[ 309.779845] i40e 0000:02:00.0: type=17 seid=160 uplink=2 downlink=0
[ 309.786111] i40e 0000:02:00.0: type=19 seid=390 uplink=160 downlink=16
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Although the i40e supports so-called floating VEB (VEB without
an uplink connection to external network), this support is
broken. This functionality is currently unused (except debugfs)
but it will be used by subsequent series for switchdev mode
slow-path. Fix this by following:
1) Handle correctly floating VEB (VEB with uplink_seid == 0)
in i40e_reconstitute_veb() and look for owner VSI and
create it only for non-floating VEBs and also set bridge
mode only for such VEBs as the floating ones are using
always VEB mode.
2) Handle correctly floating VEB in i40e_veb_release() and
disallow its release when there are some VSIs. This is
different from regular VEB that have owner VSI that is
connected to VEB's uplink after VEB deletion by FW.
3) Fix i40e_add_veb() to handle 'vsi' that is NULL for floating
VEBs. For floating VEB use 0 for downlink SEID and 'true'
for 'default_port' parameters as per datasheet.
4) Fix 'add relay' command in i40e_dbg_command_write() to allow
to create floating VEB by 'add relay 0 0' or 'add relay'
Tested using debugfs:
1) Initial state
[root@host net-next]# echo dump switch > $CMD
[root@host net-next]# dmesg -c
[ 173.701286] i40e 0000:02:00.0: header: 3 reported 3 total
[ 173.706701] i40e 0000:02:00.0: type=19 seid=392 uplink=160 downlink=16
[ 173.713241] i40e 0000:02:00.0: type=17 seid=160 uplink=2 downlink=0
[ 173.719507] i40e 0000:02:00.0: type=19 seid=390 uplink=160 downlink=16
2) Add floating VEB
[root@host net-next]# CMD="/sys/kernel/debug/i40e/0000:02:00.0/command"
[root@host net-next]# echo add relay > $CMD
[root@host net-next]# dmesg -c
[ 245.551720] i40e 0000:02:00.0: added relay 162
[root@host net-next]# echo dump switch > $CMD
[root@host net-next]# dmesg -c
[ 276.984371] i40e 0000:02:00.0: header: 4 reported 4 total
[ 276.989779] i40e 0000:02:00.0: type=19 seid=392 uplink=160 downlink=16
[ 276.996302] i40e 0000:02:00.0: type=17 seid=160 uplink=2 downlink=0
[ 277.002569] i40e 0000:02:00.0: type=19 seid=390 uplink=160 downlink=16
[ 277.009091] i40e 0000:02:00.0: type=17 seid=162 uplink=0 downlink=0
3) Add VMDQ2 VSI to this new VEB
[root@host net-next]# echo add vsi 162 > $CMD
[root@host net-next]# dmesg -c
[ 332.314030] i40e 0000:02:00.0: added VSI 394 to relay 162
[ 332.337486] enp2s0f0np0v0: NIC Link is Up, 40 Gbps Full Duplex, Flow Control: None
[root@host net-next]# echo dump switch > $CMD
[root@host net-next]# dmesg -c
[ 387.284490] i40e 0000:02:00.0: header: 5 reported 5 total
[ 387.289904] i40e 0000:02:00.0: type=19 seid=394 uplink=162 downlink=16
[ 387.296446] i40e 0000:02:00.0: type=17 seid=162 uplink=0 downlink=0
[ 387.302708] i40e 0000:02:00.0: type=19 seid=392 uplink=160 downlink=16
[ 387.309234] i40e 0000:02:00.0: type=17 seid=160 uplink=2 downlink=0
[ 387.315500] i40e 0000:02:00.0: type=19 seid=390 uplink=160 downlink=16
4) Try to delete the VEB
[root@host net-next]# echo del relay 162 > $CMD
[root@host net-next]# dmesg -c
[ 428.749297] i40e 0000:02:00.0: deleting relay 162
[ 428.754011] i40e 0000:02:00.0: can't remove VEB 162 with 1 VSIs left
5) Do PF reset and check switch status after rebuild
[root@host net-next]# echo pfr > $CMD
[root@host net-next]# echo dump switch > $CMD
[root@host net-next]# dmesg -c
[ 738.056172] i40e 0000:02:00.0: header: 5 reported 5 total
[ 738.061577] i40e 0000:02:00.0: type=19 seid=394 uplink=162 downlink=16
[ 738.068104] i40e 0000:02:00.0: type=17 seid=162 uplink=0 downlink=0
[ 738.074367] i40e 0000:02:00.0: type=19 seid=392 uplink=160 downlink=16
[ 738.080892] i40e 0000:02:00.0: type=17 seid=160 uplink=2 downlink=0
[ 738.087160] i40e 0000:02:00.0: type=19 seid=390 uplink=160 downlink=16
6) Delete VSI and delete VEB
[root@host net-next]# echo del vsi 394 > $CMD
[root@host net-next]# echo del relay 162 > $CMD
[root@host net-next]# echo dump switch > $CMD
[root@host net-next]# dmesg -c
[ 1233.081126] i40e 0000:02:00.0: deleting VSI 394
[ 1239.345139] i40e 0000:02:00.0: deleting relay 162
[ 1244.886920] i40e 0000:02:00.0: header: 3 reported 3 total
[ 1244.892328] i40e 0000:02:00.0: type=19 seid=392 uplink=160 downlink=16
[ 1244.898853] i40e 0000:02:00.0: type=17 seid=160 uplink=2 downlink=0
[ 1244.905119] i40e 0000:02:00.0: type=19 seid=390 uplink=160 downlink=16
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add two helpers i40e_(veb|vsi)_get_by_seid() to find corresponding
VEB or VSI by their SEID value and use these helpers to replace
existing open-coded loops.
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Introduce i40e_for_each_vsi() and i40e_for_each_veb() helper
macros and use them to iterate relevant arrays.
Replace pattern:
for (i = 0; i < pf->num_alloc_vsi; i++)
by:
i40e_for_each_vsi(pf, i, vsi)
and pattern:
for (i = 0; i < I40E_MAX_VEB; i++)
by
i40e_for_each_veb(pf, i, veb)
These macros also check if array item pf->vsi[i] or pf->veb[i]
are not NULL and skip such items so we can remove redundant
checks from loop bodies.
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Use existing i40e_find_vsi_by_type() to find a VSI
associated with flow director.
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2024-02-06 (igb, igc)
This series contains updates to igb and igc drivers.
Kunwu Chan adjusts firmware version string implementation to resolve
possible NULL pointer issue for igb.
Sasha removes workaround on igc.
* '1GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
igc: Remove temporary workaround
igb: Fix string truncation warnings in igb_set_fw_version
====================
Link: https://lore.kernel.org/r/20240214180347.3219650-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for LEDs on i225/i226. The LEDs can be controlled via sysfs
from user space using the netdev trigger. The LEDs are named as
igc-<bus><device>-<led> to be easily identified.
Offloading link speed and activity are supported. Other modes are simulated
in software by using on/off. Tested on Intel i225.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20240213184138.1483968-1-anthony.l.nguyen@intel.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
To fully support initializing the LAG support code, a DDP package that
extracts the logical port from the metadata is required. If such a
package is not present, there could be difficulties in supporting some
bond types.
Add a check into the initialization flow that will bypass the new paths
if any of the support pieces are missing.
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Fixes: df006dd4b1 ("ice: Add initial support framework for LAG")
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20240213183957.1483857-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
PHY_CONTROL register works as defined in the IEEE 802.3 specification
(IEEE 802.3-2008 22.2.4.1). Tidy up the temporary workaround.
User impact: PHY can now be powered down when the ethernet link is down.
Testing hints: ip link set down <device> (or just disconnect the
ethernet cable).
Oldest tested NVM version is: 1045:740.
Fixes: 5586838fe9 ("igc: Add code for PHY support")
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Commit 1978d3ead8 ("intel: fix string truncation warnings")
fixes '-Wformat-truncation=' warnings in igb_main.c by using kasprintf.
drivers/net/ethernet/intel/igb/igb_main.c:3092:53: warning：‘%d’ directive output may be truncated writing between 1 and 5 bytes into a region of size between 1 and 13 [-Wformat-truncation=]
3092 | "%d.%d, 0x%08x, %d.%d.%d",
| ^~
drivers/net/ethernet/intel/igb/igb_main.c:3092:34: note：directive argument in the range [0, 65535]
3092 | "%d.%d, 0x%08x, %d.%d.%d",
| ^~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/intel/igb/igb_main.c:3092:34: note：directive argument in the range [0, 65535]
drivers/net/ethernet/intel/igb/igb_main.c:3090:25: note：‘snprintf’ output between 23 and 43 bytes into a destination of size 32
kasprintf() returns a pointer to dynamically allocated memory
which can be NULL upon failure.
Fix this warning by using a larger space for adapter->fw_version,
and then fall back and continue to use snprintf.
Fixes: 1978d3ead8 ("intel: fix string truncation warnings")
Signed-off-by: Kunwu Chan <chentao@kylinos.cn>
Cc: Kunwu Chan <kunwu.chan@hotmail.com>
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2024-02-12 (i40e)
This series contains updates to i40e driver only.
Ivan Vecera corrects the looping value used while waiting for queues to
be disabled as well as an incorrect mask being used for DCB
configuration.
Maciej resolves an issue related to XDP traffic; removing a double call to
i40e_pf_rxq_wait() and accounting for XDP rings when stopping rings.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Seth reported that on his side XDP traffic can not survive a round of
down/up against i40e interface. Dmesg output was telling us that we were
not able to disable the very first XDP ring. That was due to the fact
that in i40e_vsi_stop_rings() in a pre-work that is done before calling
i40e_vsi_wait_queues_disabled(), XDP Tx queues were not taken into the
account.
To fix this, let us distinguish between Rx and Tx queue boundaries and
take into the account XDP queues for Tx side.
Reported-by: Seth Forshee <sforshee@kernel.org>
Closes: https://lore.kernel.org/netdev/ZbkE7Ep1N1Ou17sA@do-x1extreme/
Fixes: 65662a8dcd ("i40e: Fix logic of disabling queues")
Tested-by: Seth Forshee <sforshee@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Reviewed-by: Ivan Vecera <ivecera@redhat.com>
Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com> (A Contingent Worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently, when interface is being brought down and
i40e_vsi_stop_rings() is called, i40e_pf_rxq_wait() is called two times,
which is wrong. To showcase this scenario, simplified call stack looks
as follows:
i40e_vsi_stop_rings()
i40e_control wait rx_q()
i40e_control_rx_q()
i40e_pf_rxq_wait()
i40e_vsi_wait_queues_disabled()
i40e_pf_rxq_wait() // redundant call
To fix this, let us s/i40e_control_wait_rx_q/i40e_control_rx_q within
i40e_vsi_stop_rings().
Fixes: 65662a8dcd ("i40e: Fix logic of disabling queues")
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Reviewed-by: Ivan Vecera <ivecera@redhat.com>
Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com> (A Contingent Worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Mask used for clearing PRTDCB_RETSTCC register in function
i40e_dcb_hw_rx_ets_bw_config() is incorrect as there is used
define I40E_PRTDCB_RETSTCC_ETSTC_SHIFT instead of define
I40E_PRTDCB_RETSTCC_ETSTC_MASK.
The PRTDCB_RETSTCC register is used to configure whether ETS
or strict priority is used as TSA in Rx for particular TC.
In practice it means that once the register is set to use ETS
as TSA then it is not possible to switch back to strict priority
without CoreR reset.
Fix the value in the clearing mask.
Fixes: 90bc8e003b ("i40e: Add hardware configuration for software based DCB")
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The function i40e_pf_wait_queues_disabled() iterates all PF's VSIs
up to 'pf->hw.func_caps.num_vsis' but this is incorrect because
the real number of VSIs can be up to 'pf->num_alloc_vsi' that
can be higher. Fix this loop.
Fixes: 69129dc39f ("i40e: Modify Tx disable wait flow in case of DCB reconfiguration")
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently when PF administratively sets VF's MAC address and the VF
is put down (VF tries to delete all MACs) then the MAC is removed
from MAC filters and primary VF MAC is zeroed.
Do not allow untrusted VF to remove primary MAC when it was set
administratively by PF.
Reproducer:
1) Create VF
2) Set VF interface up
3) Administratively set the VF's MAC
4) Put VF interface down
[root@host ~]# echo 1 > /sys/class/net/enp2s0f0/device/sriov_numvfs
[root@host ~]# ip link set enp2s0f0v0 up
[root@host ~]# ip link set enp2s0f0 vf 0 mac fe:6c:b5:da:c7:7d
[root@host ~]# ip link show enp2s0f0
23: enp2s0f0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP mode DEFAULT group default qlen 1000
link/ether 3c:ec:ef:b7:dd:04 brd ff:ff:ff:ff:ff:ff
vf 0 link/ether fe:6c:b5:da:c7:7d brd ff:ff:ff:ff:ff:ff, spoof checking on, link-state auto, trust off
[root@host ~]# ip link set enp2s0f0v0 down
[root@host ~]# ip link show enp2s0f0
23: enp2s0f0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP mode DEFAULT group default qlen 1000
link/ether 3c:ec:ef:b7:dd:04 brd ff:ff:ff:ff:ff:ff
vf 0 link/ether 00:00:00:00:00:00 brd ff:ff:ff:ff:ff:ff, spoof checking on, link-state auto, trust off
Fixes: 700bbf6c1f ("i40e: allow VF to remove any MAC filter")
Fixes: ceb29474bb ("i40e: Add support for VF to specify its primary MAC address")
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20240208180335.1844996-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
During devlink reload it is needed to remove debugfs entries
correlated with only one PF. ice_debugfs_exit() removes all
entries created by ice driver so we can't use it.
Introduce ice_debugfs_pf_deinit() in order to release PF's
debugfs entries. Move ice_debugfs_exit() call to ice_module_exit(),
it makes more sense since ice_debugfs_init() is called in
ice_module_init() and not in ice_probe().
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Reviewed-by: Brett Creeley <brett.creeley@amd.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Recent changes to the devlink reload (commit 9b2348e2d6
("devlink: warn about existing entities during reload-reinit"))
force the drivers to destroy devlink ports during reinit.
Adjust ice driver to this requirement, unregister netdvice, destroy
devlink port. ice_init_eth() was removed and all the common code
between probe and reload was moved to ice_load().
During devlink reload we can't take devl_lock (it's already taken)
and in ice_probe() we have to lock it. Use devl_* variant of the API
which does not acquire and release devl_lock. Guard ice_load()
with devl_lock only in case of probe.
Suggested-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Brett Creeley <brett.creeley@amd.com>
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
E825C devices shall support the new signing type of RSA 3K for new DDP
section (SEGMENT_SIGN_TYPE_RSA3K_E825 (5) - already in the code).
The driver is responsible to verify the presence of correct signing type.
Add 3k signinig support for E825C devices based on mac_type:
ICE_MAC_GENERIC_3K_E825;
Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
E800 series devices have a couple of quirks:
1. Sideband control queues are not supported
2. The registers that the driver needs to program for the "Precision
Time Protocol (PTP)" feature are different for E800 series devices
compared to other devices supported by this driver.
Both these require conditional logic based on the underlying device we
are dealing with.
The function ice_is_sbq_supported added by commit 8f5ee3c477
("ice: add support for sideband messages") addresses (1).
The same function can be used to address (2) as well
but this just looks weird readability wise in cases that have nothing
to do with sideband control queues:
if (ice_is_sbq_supported(hw))
/* program register A */
else
/* program register B */
For these cases, the function ice_is_generic_mac introduced by this
patch communicates the idea/intention better. Also rework
ice_is_sbq_supported to use this new function.
As side-band queue is supported for E825C devices, it's mac_type is
considered as generic mac_type.
Co-developed-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Introduce new Intel Ethernet E825C family devices.
Add new PCI device IDs which are going to be supported by the
driver:
- 579C: Intel(R) Ethernet Connection E825-C for backplane
- 579D: Intel(R) Ethernet Connection E825-C for QSFP
- 579E: Intel(R) Ethernet Connection E825-C for SFP
- 579F: Intel(R) Ethernet Connection E825-C for SGMII
Add helper function ice_is_e825c() to verify if the running device
belongs to E825C family.
Co-developed-by: Jan Glaza <jan.glaza@intel.com>
Signed-off-by: Jan Glaza <jan.glaza@intel.com>
Co-developed-by: Michal Michalik <michal.michalik@intel.com>
Signed-off-by: Michal Michalik <michal.michalik@intel.com>
Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tony Nguyen says:
====================
igc: ethtool: Flex filter cleanup
Kurt Kanzenbach says:
This series contains some cosmetics for the flex filter code. The fixes have
been merged separately via -net already.
* '1GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
igc: Unify filtering rule fields
igc: Use netdev printing functions for flex filters
igc: Use reverse xmas tree
====================
Link: https://lore.kernel.org/r/20240207191656.1250777-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2024-02-06 (ixgbe)
This series contains updates to ixgbe driver only.
Jedrzej continues cleanup work from conversion away from ixgbe_status;
s32 values are changed to int, various style issues are addressed, and
some return statements refactored to address some smatch warnings.
* '10GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
ixgbe: Clarify the values of the returning status
ixgbe: Rearrange args to fix reverse Christmas tree
ixgbe: Convert ret val type from s32 to int
====================
Link: https://lore.kernel.org/r/20240206214054.1002919-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Cross-merge networking fixes after downstream PR.
No conflicts.
Adjacent changes:
drivers/net/ethernet/stmicro/stmmac/common.h
38cc3c6dcc ("net: stmmac: protect updates of 64-bit statistics counters")
fd5a6a7131 ("net: stmmac: est: Per Tx-queue error count for HLBF")
c5c3e1bfc9 ("net: stmmac: Offload queueMaxSDU from tc-taprio")
drivers/net/wireless/microchip/wilc1000/netdev.c
c901388028 ("wifi: fill in MODULE_DESCRIPTION()s for wilc1000")
328efda22a ("wifi: wilc1000: do not realloc workqueue everytime an interface is added")
net/unix/garbage.c
11498715f2 ("af_unix: Remove io_uring code for GC.")
1279f9d9de ("af_unix: Call kfree_skb() for dead unix_(sk)->oob_skb in GC.")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
All filtering parameters such as EtherType and VLAN TCI are stored in host
byte order except for the VLAN EtherType. Unify it.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
All igc filter implementations use netdev_*() printing functions except for
the flex filters. Unify it.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Use reverse xmas tree coding style convention in igc_add_flex_filter().
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The kernel build regressions/improvements email contained a couple of
issues with old compilers (in fact all the reports were on different
architectures, but all gcc 5.5) and the FIELD_PREP() and FIELD_GET()
conversions. They're all because an integer #define that should have
been declared as unsigned, was shifted to the point that it could set
the sign bit.
The fix just involves making sure the defines use the "U" identifier on
the constants to make sure they're unsigned. Should make the checkers
happier.
Confirmed with objdump before/after that there is no change to the
binaries.
Issues were reported as follows:
./drivers/net/ethernet/intel/ice/ice_base.c:238:7: note: in expansion of macro 'FIELD_GET'
(FIELD_GET(GLINT_CTL_ITR_GRAN_25_M, regval) == ICE_ITR_GRAN_US))
^
./include/linux/compiler_types.h:435:38: error: call to '__compiletime_assert_1093' declared with attribute error: FIELD_GET: mask is not constant
drivers/net/ethernet/intel/ice/ice_nvm.c:709:16: note: in expansion of macro ‘FIELD_GET’
orom->major = FIELD_GET(ICE_OROM_VER_MASK, combo_ver);
^
./include/linux/compiler_types.h:435:38: error: call to ‘__compiletime_assert_796’ declared with attribute error: FIELD_GET: mask is not constant
drivers/net/ethernet/intel/ice/ice_common.c:945:18: note: in expansion of macro ‘FIELD_GET’
u8 max_agg_bw = FIELD_GET(GL_PWR_MODE_CTL_CAR_MAX_BW_M,
^
./include/linux/compiler_types.h:435:38: error: call to ‘__compiletime_assert_420’ declared with attribute error: FIELD_GET: mask is not constant
drivers/net/ethernet/intel/i40e/i40e_dcb.c:458:8: note: in expansion of macro ‘FIELD_GET’
oui = FIELD_GET(I40E_LLDP_TLV_OUI_MASK, ouisubtype);
^
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Closes: https://lore.kernel.org/lkml/d03e90ca-8485-4d1b-5ec1-c3398e0e8da@linux-m68k.org/ #i40e #ice
Fixes: 62589808d7 ("i40e: field get conversion")
Fixes: 5a259f8e0b ("ice: field get conversion")
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Link: https://lore.kernel.org/r/20240206022906.2194214-1-jesse.brandeburg@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Converting s32 functions to regular int in the previous patch of the series
caused triggering smatch warnings about missing error code.
New smatch warnings:
drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c:2884 ixgbe_get_lcd_t_x550em() warn: missing error code? 'status'
drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c:3130 ixgbe_enter_lplu_t_x550em() warn: missing error code? 'status'
Old smatch warnings:
drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c:2890 ixgbe_get_lcd_t_x550em() warn: missing error code? 'status'
Fix it by clearly stating returning error code as 0.
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/r/202401041701.6QKTsZmx-lkp@intel.com/
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Clean up the code touched during type conversion by the previous patch
of the series.
Suggested-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently big amount of the functions returning standard error codes
are of type s32. Convert them to regular ints as typdefs here are not
necessary to return standard error codes.
Fix incorrect args alignment in touched functions.
Suggested-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Copy paste issue left a comment for this structure that has nothing
to do with FW alignment; remove the comment.
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
HW incorrectly reports EIPE errors on encapsulated packets
with L2 padding inside inner packet. HW shows outer UDP/IPV4
packet checksum errors as part of the EIPE flags of the
Rx descriptor. These are reported only if checksum offload
is enabled and L3/L4 parsed flag is valid in Rx descriptor.
When that error is reported by HW, we don't act on it
instead of incrementing main Rx errors statistic as it
would normally happen.
Add a new statistic to count these errors since we still want
to print them.
Signed-off-by: Aniruddha Paul <aniruddha.paul@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Jan Glaza <jan.glaza@intel.com>
Signed-off-by: Jan Sokolowski <jan.sokolowski@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently, XSK control path in ice driver calls directly
ice_vsi_cfg_txq() whereas we have ice_vsi_cfg_single_txq() for that
purpose. Use the latter from XSK side and make ice_vsi_cfg_txq() static.
ice_vsi_cfg_txq() resides in ice_base.c and is rather big, so to reduce
the code churn let us move the callers of it from ice_lib.c to
ice_base.c.
This change puts ice_qp_ena() on nice diet due to the checks and
operations that ice_vsi_cfg_single_{r,t}xq() do internally.
add/remove: 0/0 grow/shrink: 0/1 up/down: 0/-182 (-182)
Function old new delta
ice_xsk_pool_setup 2165 1983 -182
Total: Before=472597, After=472415, chg -0.04%
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Acked-by: Magnus Karlsson <magnus.karlsson@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com> (A Contingent Worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently, XSK control path in ice driver calls directly
ice_vsi_cfg_rxq() whereas we have ice_vsi_cfg_single_rxq() for that
purpose. Use the latter from XSK side and make ice_vsi_cfg_rxq() static.
ice_vsi_cfg_rxq() resides in ice_base.c and is rather big, so to reduce
the code churn let us move two callers of it from ice_lib.c to
ice_base.c.
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Acked-by: Magnus Karlsson <magnus.karlsson@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com> (A Contingent Worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
In the arm random config file, kconfig option 'CONFIG_AEABI' is
disabled which results in adding the compiler flag '-mabi=apcs-gnu'.
This causes the compiler to add padding in virtchnl2_ptype
structure to align it to 8 bytes, resulting in the following
size check failure:
include/linux/build_bug.h:78:41: error: static assertion failed: "(6) == sizeof(struct virtchnl2_ptype)"
78 | #define __static_assert(expr, msg, ...) _Static_assert(expr, msg)
| ^~~~~~~~~~~~~~
include/linux/build_bug.h:77:34: note: in expansion of macro '__static_assert'
77 | #define static_assert(expr, ...) __static_assert(expr, ##__VA_ARGS__, #expr)
| ^~~~~~~~~~~~~~~
drivers/net/ethernet/intel/idpf/virtchnl2.h:26:9: note: in expansion of macro 'static_assert'
26 | static_assert((n) == sizeof(struct X))
| ^~~~~~~~~~~~~
drivers/net/ethernet/intel/idpf/virtchnl2.h:982:1: note: in expansion of macro 'VIRTCHNL2_CHECK_STRUCT_LEN'
982 | VIRTCHNL2_CHECK_STRUCT_LEN(6, virtchnl2_ptype);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~
Avoid the compiler padding by using "__packed" structure
attribute for the virtchnl2_ptype struct. Also align the
structure by using "__aligned(2)" for better code optimization.
Fixes: 0d7502a9b4 ("virtchnl: add virtchnl version 2 ops")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202312220250.ufEm8doQ-lkp@intel.com
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Pavan Kumar Linga <pavan.kumar.linga@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20240131222241.2087516-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pass additional argunent status_error over lock_status_get()
so drivers can fill it up. In case they do, expose the value over
previously introduced attribute to user. Do it only in case the
current lock_status is either "unlocked" or "holdover".
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Acked-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This is in preparation of using the existing names for linkmode
bitmaps.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to pass EEE link modes beyond bit 32 to userspace we have to
complement the 32 bit bitmaps in struct ethtool_eee with linkmode
bitmaps. Therefore, similar to ethtool_link_settings and
ethtool_link_ksettings, add a struct ethtool_keee. In a first step
it's an identical copy of ethtool_eee. This patch simply does a
s/ethtool_eee/ethtool_keee/g for all users.
No functional change intended.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ice driver currently attempts to destroy and re-initialize the Tx
timestamp tracker during the reset flow. The release of the Tx tracker
only happened during CORE reset or GLOBAL reset. The ice_ptp_rebuild()
function always calls the ice_ptp_init_tx function which will allocate
a new tracker data structure, resulting in memory leaks during PF reset.
Certainly the driver should not be allocating a new tracker without
removing the old tracker data, as this results in a memory leak.
Additionally, there's no reason to remove the tracker memory during a
reset. Remove this logic from the reset and rebuild flow. Instead of
releasing the Tx tracker, flush outstanding timestamps just before we
reset the PHY timestamp block in ice_ptp_cfg_phy_interrupt().
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The ice_ptp_reset() function uses a goto to skip past clock owner
operations if performing a PF reset or if the device is not the clock
owner. This is a bit confusing. Factor this out into
ice_ptp_rebuild_owner() instead.
The ice_ptp_reset() function is called by ice_rebuild() to restore PTP
functionality after a device reset. Follow the convention set by the
ice_main.c file and rename this function to ice_ptp_rebuild(), in the
same way that we have ice_prepare_for_reset() and
ice_ptp_prepare_for_reset().
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The ice_ptp_tx_cfg_intr() function sends a control queue message to
configure the PHY timestamp interrupt block. This is a very similar name
to a function which is used to configure the MAC Other Interrupt Cause
Enable register.
Rename this function to ice_ptp_cfg_phy_interrupt in order to make it
more obvious to the reader what action it performs, and distinguish it
from other similarly named functions.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
E810 hardware does not have a Tx timestamp ready bitmap. Don't check
has_ready_bitmap in E810-specific functions.
Add has_ready_bitmap check in ice_ptp_process_tx_tstamp() to stop
relying on the fact that ice_get_phy_tx_tstamp_ready() returns all 1s.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The tx->verify_cached flag is used to inform the Tx timestamp tracking
code whether it needs to verify the cached Tx timestamp value against
a previous captured value. This is necessary on E810 hardware which does
not have a Tx timestamp ready bitmap.
In addition, we currently rely on the fact that the
ice_get_phy_tx_tstamp_ready() function returns all 1s for E810 hardware.
Instead of introducing a brand new flag, rename and verify_cached to
has_ready_bitmap, inverting the relevant checks.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The ice_ptp_prepare_for_reset() and ice_ptp_reset() functions currently
check the pf->flags ICE_FLAG_PFR_REQ bit to determine if the current
reset is a PF reset or not.
This is problematic, because it is possible that a PF reset and a higher
level reset (CORE reset, GLOBAL reset, EMP reset) are requested
simultaneously. In that case, the driver performs the highest level
reset requested. However, the ICE_FLAG_PFR_REQ flag will still be set.
The main driver reset functions take an enum ice_reset_req indicating
which reset is actually being performed. Pass this data into the PTP
functions and rely on this instead of relying on the driver flags.
This ensures that the PTP code performs the proper level of reset that
the driver is actually undergoing.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add PTP state machine so that the driver can correctly identify PTP
state around resets.
When the driver got information about ungraceful reset, PTP was not
prepared for reset and it returned error. When this situation occurs,
prepare PTP before rebuilding its structures.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Co-developed-by: Karol Kolacinski <karol.kolacinski@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
All error handling paths, except this one, go to 'out' where
release_swfw_sync() is called.
This call balances the acquire_swfw_sync() call done at the beginning of
the function.
Branch to the error handling path in order to correctly release some
resources in case of error.
Fixes: ae14a1d8e1 ("ixgbe: Fix IOSF SB access issues")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The e1000e driver supports hardware with a variety of different clock
speeds, and thus a variety of different increment values used for
programming its PTP hardware clock.
The values currently programmed in e1000e_ptp_init are incorrect. In
particular, only two maximum adjustments are used: 24000000 - 1, and
600000000 - 1. These were originally intended to be used with the 96 MHz
clock and the 25 MHz clock.
Both of these values are actually slightly too high. For the 96 MHz clock,
the actual maximum value that can safely be programmed is 23,999,938. For
the 25 MHz clock, the maximum value is 599,999,904.
Worse, several devices use a 24 MHz clock or a 38.4 MHz clock. These parts
are incorrectly assigned one of either the 24million or 600million values.
For the 24 MHz clock, this is not a significant issue: its current
increment value can support an adjustment up to 7billion in the positive
direction. However, the 38.4 KHz clock uses an increment value which can
only support up to 230,769,157 before it starts overflowing.
To understand where these values come from, consider that frequency
adjustments have the form of:
new_incval = base_incval + (base_incval * adjustment) / (unit of adjustment)
The maximum adjustment is reported in terms of parts per billion:
new_incval = base_incval + (base_incval * adjustment) / 1 billion
The largest possible adjustment is thus given by the following:
max_incval = base_incval + (base_incval * max_adj) / 1 billion
Re-arranging to solve for max_adj:
max_adj = (max_incval - base_incval) * 1 billion / base_incval
We also need to ensure that negative adjustments cannot underflow. This can
be achieved simply by ensuring max_adj is always less than 1 billion.
Introduce new macros in e1000.h codifying the maximum adjustment in PPB for
each frequency given its associated increment values. Also clarify where
these values come from by commenting about the above equations.
Replace the switch statement in e1000e_ptp_init with one which mirrors the
increment value switch statement from e1000e_get_base_timinica. For each
device, assign the appropriate maximum adjustment based on its frequency.
Some parts can have one of two frequency modes as determined by
E1000_TSYNCRXCTL_SYSCFI.
Since the new flow directly matches the assignments in
e1000e_get_base_timinca, and uses well defined macro names, it is much
easier to verify that the resulting maximum adjustments are correct. It
also avoids difficult to parse construction such as the "hw->mac.type <
e1000_phc_lpt", and the use of fallthrough which was especially confusing
when combined with a conditional block.
Note that I believe the current increment value configuration used for
24MHz clocks is sub-par, as it leaves at least 3 extra bits available in
the INCVALUE register. However, fixing that requires more careful review of
the clock rate and associated values.
Reported-by: Trey Harrison <harrisondigitalmedia@gmail.com>
Fixes: 68fe1d5da5 ("e1000e: Add Support for 38.4MHZ frequency")
Fixes: d89777bf0e ("e1000e: add support for IEEE-1588 PTP")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
