If a VM reboots and/or VF driver is unloaded, its cached hardware MAC
address (hw_lan_addr.addr) is cleared in some cases. If the VF is
trusted, then the PF driver allows the VF to clear its old MAC address
even if this MAC was configured by a host administrator. If the VF is
untrusted, then the PF driver allows the VF to clear its old MAC
address only if the host admin did not set it.
For the trusted VF case, this is unexpected and will cause issues
because the host configured MAC (i.e. via XML) will be cleared on VM
reboot. For the untrusted VF case, this is done to be consistent and it
will allow the VF to keep the same MAC across VM reboot.
Fix this by introducing dev_lan_addr to the VF structure. This will be
the VF's MAC address when it's up and running and in most cases will be
the same as the hw_lan_addr. However, to address the VM reboot and
unload/reload problem, the driver will never allow the hw_lan_addr to be
cleared via VIRTCHNL_OP_DEL_ETH_ADDR. When the VF's MAC is changed, the
dev_lan_addr and hw_lan_addr will always be updated with the same value.
The only ways the VF's MAC can change are the following:
- Set the VF's MAC administratively on the host via iproute2.
- If the VF is trusted and changes/sets its own MAC.
- If the VF is untrusted and the host has not set the MAC via iproute2.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently there is no way for a VF driver to specify if it wants to
change it's hardware address. New bits are being added to virtchnl.h
in struct virtchnl_ether_addr that allow for the VF to correctly
communicate this information. However, legacy VF drivers that don't
support the new virtchnl.h bits still need to be supported. Make a
best effort attempt at saving the VF's primary/device address in the
legacy case and depend on the VIRTCHNL_ETHER_ADDR_PRIMARY type for
the new case.
Legacy case - If a unicast MAC is being added and the
hw_lan_addr.addr is empty, then populate it. This assumes that the
address is the VF's hardware address. If a unicast MAC is being
added and the hw_lan_addr.addr is not empty, then cache it in the
legacy_last_added_umac.addr. If a unicast MAC is being deleted and it
matches the hw_lan_addr.addr, then zero the hw_lan_addr.addr.
Also, if the legacy_last_added_umac.addr has not expired, copy the
legacy_last_added_umac.addr into the hw_lan_addr.addr. This is done
because we cannot guarantee the order of VIRTCHNL_OP_ADD_ETH_ADDR and
VIRTCHNL_OP_DEL_ETH_ADDR.
New case - If a unicast MAC is being added and it's specified as
VIRTCHNL_ETHER_ADDR_PRIMARY, then replace the current
hw_lan_addr.addr. If a unicast MAC is being deleted and it's type
is specified as VIRTCHNL_ETHER_ADDR_PRIMARY, then zero the
hw_lan_addr.addr.
Untrusted VFs - Only allow above legacy/new changes to their
hardware address if the PF has not set it administratively via
iproute2.
Trusted VFs - Always allow above legacy/new changes to their
hardware address even if the PF has administratively set it via
iproute2.
Also, change the variable dflt_lan_addr to hw_lan_addr to clearly
represent the purpose of this variable since it's purpose is to
act as a hardware programmed MAC address for the VF.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add HW VLAN acceleration protocol handling. In case of HW VLAN tagging,
we need that protocol available in the ndo_start_xmit(), so that it will be
stored in a new fields in the skb.
HW offloading is set to OFF by default.
Users are allow to turn on/off Rx/Tx HW VLAN acceleration via ethtool.
Signed-off-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Acked-by: Sasha Neftin <sasha.neftin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Minor fix of indentation in igc_defines.h
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The MDICNFG register from igc registers is not used so remove it.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The CR_1000T_ASYM_PAUSE bit from igc defines is not used so remove it.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Complete to commit c8d4725e98 ("intel: Update drivers to use
ethtool_sprintf")
Update the igc driver to make use of ethtool_sprintf. The general idea
is to reduce code size and overhead by replacing the repeated pattern of
string printf statements and ETH_STRING_LEN counter increments.
Suggested-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tony Nguyen says:
====================
iwl-next Intel Wired LAN Driver Updates 2021-06-01
This pull request is targeting net-next and rdma-next branches.
These patches have been reviewed by netdev and rdma mailing lists[1].
This series adds RDMA support to the ice driver for E810 devices and
converts the i40e driver to use the auxiliary bus infrastructure
for X722 devices. The PCI netdev drivers register auxiliary RDMA devices
that will bind to auxiliary drivers registered by the new irdma module.
[1] https://lore.kernel.org/netdev/20210520143809.819-1-shiraz.saleem@intel.com/
---
v3:
- ice_aq_add_rdma_qsets(), ice_cfg_vsi_rdma(), ice_[ena|dis]_vsi_rdma_qset(),
and ice_cfg_rdma_fltr() no longer return ice_status
- Remove null check from ice_aq_add_rdma_qsets()
v2:
- Added patch 'i40e: Replace one-element array with flexible-array
member'
Changes since linked review (v6):
- Removed unnecessary checks in i40e_client_device_register() and
i40e_client_device_unregister()
- Simplified the i40e_client_device_register() API
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
If CONFIG_IGB_HWMON is n, gcc warns:
drivers/net/ethernet/intel/igb/e1000_82575.c:2765:17:
warning: ‘e1000_emc_therm_limit’ defined but not used [-Wunused-const-variable=]
static const u8 e1000_emc_therm_limit[4] = {
^~~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/intel/igb/e1000_82575.c:2759:17:
warning: ‘e1000_emc_temp_data’ defined but not used [-Wunused-const-variable=]
static const u8 e1000_emc_temp_data[4] = {
^~~~~~~~~~~~~~~~~~~
Move it into #ifdef block to fix this.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert i40e to use the auxiliary bus infrastructure to export
the RDMA functionality of the device to the RDMA driver.
Register i40e client auxiliary RDMA device on the auxiliary bus per
PCIe device function for the new auxiliary rdma driver (irdma) to
attach to.
The global i40e_register_client and i40e_unregister_client symbols
will be obsoleted once irdma replaces i40iw in the kernel
for the X722 device.
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Register ice client auxiliary RDMA device on the auxiliary bus per
PCIe device function for the auxiliary driver (irdma) to attach to.
It allows to realize a single RDMA driver (irdma) capable of working with
multiple netdev drivers over multi-generation Intel HW supporting RDMA.
There is no load ordering dependencies between ice and irdma.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add implementations for supporting iidc operations for device operation
such as allocation of resources and event notifications.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Probe the device's capabilities to see if it supports RDMA. If so, allocate
and reserve resources to support its operation; populate structures with
initial values.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Replace union with a couple of pointers in order to fix the following
out-of-bounds warning:
CC [M] drivers/net/ethernet/intel/ixgbe/ixgbe_common.o
drivers/net/ethernet/intel/ixgbe/ixgbe_common.c: In function ‘ixgbe_host_interface_command’:
drivers/net/ethernet/intel/ixgbe/ixgbe_common.c:3729:13: warning: array subscript 1 is above array bounds of ‘u32[1]’ {aka ‘unsigned int[1]’} [-Warray-bounds]
3729 | bp->u32arr[bi] = IXGBE_READ_REG_ARRAY(hw, IXGBE_FLEX_MNG, bi);
| ~~~~~~~~~~^~~~
drivers/net/ethernet/intel/ixgbe/ixgbe_common.c:3682:7: note: while referencing ‘u32arr’
3682 | u32 u32arr[1];
| ^~~~~~
This helps with the ongoing efforts to globally enable -Warray-bounds.
Link: https://github.com/KSPP/linux/issues/109
Co-developed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20210527173424.362456-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There is a regular need in the kernel to provide a way to declare having a
dynamically sized set of trailing elements in a structure. Kernel code
should always use “flexible array members”[1] for these cases. The older
style of one-element or zero-length arrays should no longer be used[2].
Refactor the code according to the use of a flexible-array member in struct
i40e_qvlist_info instead of one-element array, and use the struct_size()
helper.
[1] https://en.wikipedia.org/wiki/Flexible_array_member
[2] https://www.kernel.org/doc/html/v5.10/process/deprecated.html#zero-length-and-one-element-arrays
Link: https://github.com/KSPP/linux/issues/79
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Acked-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Fix the sparse warnings in the ixgbe crypto offload code. These
changes were made in the most conservative way (force cast)
in order to hopefully not break the code. I suspect that the
code might still be broken on big-endian architectures, but
no one is complaining, so I'm just leaving it functionally
the same.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Shannon Nelson <snelson@pensando.io>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The ixgbe hardware needs some very specific programming for
certain registers, which led to some misguided usage of ntohs
instead of using be16_to_cpu(), as well as a home grown swap
followed by an ntohs. Sparse didn't like this at all, and this
fixes the C=2 build, with code that uses native kernel interface.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The igbvf driver for some reason never strongly typed it's descriptor
formats. Make this driver like the rest of the Intel drivers and use
__le* for our little endian descriptors.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The sparse build (C=2) found that there were two drivers
who had not been convered to call the csum_replace_by_diff() function
with sparse clean arguments. Most if not all drivers force the cast
like this patch does. So these drivers are now joining the party
(a bit late), but with no functional change.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The igb PTP code was using htons() on a constant to try to
byte swap the value before writing it to a register. This byte
swap has the consequence of triggering sparse conflicts between
the register write which expect cpu ordered input, and the code
which generated a big endian constant. Just override the cast
to make sure code doesn't change but silence the warning.
Can't do a __swab16 in this case because big endian systems
would then write the wrong value.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The igb driver was trying hard to be sparse correct, but somehow
ended up converting a variable into little endian order and then
tries to OR something with it.
A much plainer way of doing things is to leave all variables and
OR operations in CPU (non-endian) mode, and then convert to
little endian only once, which is what this change does.
This probably fixes a bug that might have been seen only on
big endian systems.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The sparse build (C=2) finds some issues with how the driver
dealt with the (very difficult) hardware that in some generations
uses little-endian, and in others uses big endian, for the VLAN
field. The code as written picks __le16 as a type and for some
hardware revisions we override it to __be16 as done in this
patch. This impacted the VF driver as well so fix it there too.
Also change the vlan_tci assignment to override the sparse
warning without changing functionality.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The igb and igc driver both use a trick of creating a local type
pointer on the stack to ease dealing with a receive descriptor in
64 bit chunks for printing. Sparse however was not taken into
account and receive descriptors are always in little endian
order, so just make the unions use __le64 instead of u64.
No functional change.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The error check and set_bit are placed in such a way that sparse (C=2)
warns:
.../fm10k_pci.c:1395:9: warning: context imbalance in 'fm10k_msix_mbx_pf' - different lock contexts for basic block
Which seems a little odd, but the code can obviously be moved
to where the variable is being set without changing functionality
at all, and it even seems to make a bit more sense with the check
closer to the set.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The sparse checker (C=2) found an assignment where we were mixing
types when trying to convert from data read directly from the
device NVM, to an array in CPU order in-memory, which
unfortunately the driver tries to do in-place.
This is easily solved by using the swap operation instead of an
assignment, and is already proven in other Intel drivers to be
functionally correct and the same code, just without a sparse
warning.
The change is the same in all three drivers.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Sparse tool was warning on some implicit conversions from
little endian data read from the EEPROM on the e100 cards.
Fix these by being explicit about the conversions using
le16_to_cpu().
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Check that the MTU value requested by the VF is in the supported
range of MTUs before attempting to set the VF large packet enable,
otherwise reject the request. This also avoids unnecessary
register updates in the case of the 82599 controller.
Fixes: 872844ddb9 ("ixgbe: Enable jumbo frames support w/ SR-IOV")
Co-developed-by: Piotr Skajewski <piotrx.skajewski@intel.com>
Signed-off-by: Piotr Skajewski <piotrx.skajewski@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Co-developed-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for transmitting packets via AF_XDP zero-copy mechanism.
The packet transmission itself is implemented by igc_xdp_xmit_zc() which
is called from igc_clean_tx_irq() when the ring has AF_XDP zero-copy
enabled. Likewise i40e and ice drivers, the transmission budget used is
the number of descriptors available on the ring.
A new tx buffer type is introduced to 'enum igc_tx_buffer_type' to
indicate the tx buffer uses memory from xsk pool so it can be properly
cleaned after transmission or when the ring is cleaned.
The I225 controller has only 4 Tx hardware queues so the main difference
between igc and other Intel drivers that support AF_XDP zero-copy is
that there is no tx ring dedicated exclusively to XDP. Instead, tx
rings are shared between the network stack and XDP, and netdev queue
lock is used to ensure mutual exclusion. This is the same approach
implemented to support XDP_TX and XDP_REDIRECT actions.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Signed-off-by: Vedang Patel <vedang.patel@intel.com>
Signed-off-by: Jithu Joseph <jithu.joseph@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add support for receiving packets via AF_XDP zero-copy mechanism.
Add a new flag to 'enum igc_ring_flags_t' to indicate the ring has
AF_XDP zero-copy enabled so proper ring setup is carried out during ring
configuration in igc_configure_rx_ring().
RX buffers can now be allocated via the shared pages mechanism (default
behavior of the driver) or via xsk pool (when AF_XDP zero-copy is
enabled) so a union is added to the 'struct igc_rx_buffer' to cover both
cases.
When AF_XDP zero-copy is enabled, rx buffers are allocated from the xsk
pool using the new helper igc_alloc_rx_buffers_zc() which is the
counterpart of igc_alloc_rx_buffers().
Likewise other Intel drivers that support AF_XDP zero-copy, in igc we
have a dedicated path for cleaning up rx irqs when zero-copy is enabled.
This avoids adding too many checks within igc_clean_rx_irq(), resulting
in a more readable and efficient code since this function is called from
the hot-path of the driver.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Signed-off-by: Vedang Patel <vedang.patel@intel.com>
Signed-off-by: Jithu Joseph <jithu.joseph@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Up to this point, Tx buffers are associated with either a skb or a xdpf,
and the IGC_TX_FLAGS_XDP flag was enough to distinguish between these
two case. However, with upcoming patches that will add AF_XDP zero-copy
support, a third case will be introduced so this flag-based approach
won't fit well.
In preparation to land AF_XDP zero-copy support, replace the
IGC_TX_FLAGS_XDP flag by an enum which will be extended once zero-copy
support is introduced to the driver.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Signed-off-by: Vedang Patel <vedang.patel@intel.com>
Signed-off-by: Jithu Joseph <jithu.joseph@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
In preparation for AF_XDP zero-copy support, encapsulate the code that
unmaps Tx buffers into its own local helper so we can reuse it, avoiding
code duplication.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Signed-off-by: Vedang Patel <vedang.patel@intel.com>
Signed-off-by: Jithu Joseph <jithu.joseph@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
In preparation for AF_XDP zero-copy support, encapsulate the code that
updates the driver RX stats in its own local helper so it can be reused
in the zero-copy path. Likewise, encapsulate TX stats code as well.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Signed-off-by: Vedang Patel <vedang.patel@intel.com>
Signed-off-by: Jithu Joseph <jithu.joseph@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Refactor XDP rxq info registration code, preparing the driver for AF_XDP
zero-copy support which is added by upcoming patches.
Currently, xdp_rxq and memory model are both registered during RX
resource setup time by igc_xdp_register_rxq_info() helper. With AF_XDP,
we want to register the memory model later on while configuring the ring
because we will know which memory model type to register
(MEM_TYPE_PAGE_SHARED or MEM_TYPE_XSK_BUFF_POOL).
The helpers igc_xdp_register_rxq_info() and igc_xdp_unregister_rxq_
info() are not useful anymore so they are removed.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Signed-off-by: Vedang Patel <vedang.patel@intel.com>
Signed-off-by: Jithu Joseph <jithu.joseph@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Refactor igc_clean_rx_ring() helper, preparing the code for AF_XDP
zero-copy support which is added by upcoming patches.
The refactor consists of encapsulating page-shared specific code into
its own helper, leaving common code that will be shared by both
page-shared and xsk pool in igc_clean_rx_ring().
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Signed-off-by: Vedang Patel <vedang.patel@intel.com>
Signed-off-by: Jithu Joseph <jithu.joseph@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Refactor __igc_xdp_run_prog() helper from igc_xdp_run_prog(),
preparing the code for AF_XDP zero-copy support which is added
by upcoming patches.
The existing igc_xdp_run_prog() caters to regular XDP rx path
which has to verify if bpf_prog is not NULL. Zero-copy
path assumes that bpf_prog is not NULL and hence this check is
not required. Therefore it makes sense to refactor the common
code into a helper function, to avoid code duplication.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Signed-off-by: Vedang Patel <vedang.patel@intel.com>
Signed-off-by: Jithu Joseph <jithu.joseph@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Move the helper igc_xdp_is_enabled() to igc_xdp.h so it can be reused in
igc_xdp.c by upcoming patches that will introduce AF_XDP zero-copy
support to the driver.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Signed-off-by: Vedang Patel <vedang.patel@intel.com>
Signed-off-by: Jithu Joseph <jithu.joseph@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
There is a misspell word "retreived" in comment, so fix it to "retrieved".
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are double "slot" in comment, so remove the redundant one.
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are double "the" in comment, so remove the redundant one.
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are double "in" and "to" in comments, so remove the redundant one.
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are double "slot" in comment, so remove the redundant one.
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make use of the xdp_{init,prepare}_buff() helpers instead of
an open-coded version.
Signed-off-by: Matteo Croce <mcroce@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove filters from being setup in case of software DCB and allow the
LLDP frames to be properly transmitted to the wire.
It is not possible to transmit the LLDP frame out of the port, if they
are filtered by control VSI. This prohibits software LLDP agent
properly communicate its DCB capabilities to the neighbors.
Fixes: 4b208eaa80 ("i40e: Add init and default config of software based DCB")
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Tested-by: Imam Hassan Reza Biswas <imam.hassan.reza.biswas@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Unlike other supported adapters, 2.5G and 5G use different
PHY type identifiers for reading/writing PHY settings
and for reading link status. This commit introduces
separate PHY identifiers for these two operation types.
Fixes: 2e45d3f467 ("i40e: Add support for X710 B/P & SFP+ cards")
Signed-off-by: Dawid Lukwinski <dawid.lukwinski@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
When FEC mode was changed the link didn't know it because
the link was not reset and new parameters were not negotiated.
Set a flag 'I40E_AQ_PHY_ENABLE_ATOMIC_LINK' in 'abilities'
to restart the link and make it run with the new settings.
Fixes: 1d96340196 ("i40e: Add support FEC configuration for Fortville 25G")
Signed-off-by: Jaroslaw Gawin <jaroslawx.gawin@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently the call to i40e_client_del_instance frees the object
pf->cinst, however pf->cinst->lan_info is being accessed after
the free. Fix this by adding the missing return.
Addresses-Coverity: ("Read from pointer after free")
Fixes: 7b0b1a6d0a ("i40e: Disable iWARP VSI PETCP_ENA flag on netdev down events")
Signed-off-by: Yunjian Wang <wangyunjian@huawei.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Commit 12738ac475 ("i40e: Fix sparse errors in i40e_txrx.c") broke
XDP support in the i40e driver. That commit was fixing a sparse error
in the code by introducing a new variable xdp_res instead of
overloading this into the skb pointer. The problem is that the code
later uses the skb pointer in if statements and these where not
extended to also test for the new xdp_res variable. Fix this by adding
the correct tests for xdp_res in these places.
The skb pointer was used to store the result of the XDP program by
overloading the results in the error pointer
ERR_PTR(-result). Therefore, the allocation failure test that used to
only test for !skb now need to be extended to also consider !xdp_res.
i40e_cleanup_headers() had a check that based on the skb value being
an error pointer, i.e. a result from the XDP program != XDP_PASS, and
if so start to process a new packet immediately, instead of populating
skb fields and sending the skb to the stack. This check is not needed
anymore, since we have added an explicit test for xdp_res being set
and if so just do continue to pick the next packet from the NIC.
Fixes: 12738ac475 ("i40e: Fix sparse errors in i40e_txrx.c")
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Tested-by: Jesper Dangaard Brouer <brouer@redhat.com>
Reported-by: Jesper Dangaard Brouer <brouer@redhat.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
When the FDIR entry is found, just return the result directly to break
the loop.
Signed-off-by: Haiyue Wang <haiyue.wang@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
