The calcs folder has FPU code on it, which should be isolated inside the
DML folder as per https://patchwork.freedesktop.org/series/93042/.
This commit aims single-handedly to correct the location of such FPU
code and does not refactor any functions.
Changes since v2:
- Corrected problems to compile when DCN was disabled.
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Isabella Basso <isabbasso@riseup.net>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This version brings along following fixes:
- Organize FPU associated code to DML
- Modify SMU_TIMEOUT macro
- Organize dcn201 code
- Address DS stays disabled problem under specific scenario
- Fix black screen issue
- Update DML to rev.99
- Address problem of eDP hot-plug feature
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For allow eDP hot-plug feature, the stream signal may change to VIRTUAL
when plug-out and back to eDP when plug-in. OS will still setPathMode
with same timing for each plugging, but eDP gets no stream update as we
don't check signal type changing back as keeping it VIRTUAL. It's also
unsafe for future cases that stream signal is switched with same timing.
[How]
Check stream signal type change include previous HDMI signal case.
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Dale Zhao <dale.zhao@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
1. update dml to rev.99
2. add smu clk table w/a: smu gives 1 dtm level with mismatch votage
table which causes multiple issues.
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
With some monitors when multi plane overlay is enabled the memory
clock switching mechanism has to change and, due to an error in the
initialization sequence, it may cause a black screen.
[HOW]
Change the firmware assisted memory clock switch initialization and
tear-down sequence utilizing the prepare_bandwidth and
optimize_bandwidth contexts.
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Felipe Clark <feclark@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
On HG APU + dGPU scenario with no display to dGPU,
DS stays disabled due to no display present.
This problem can be worked around by DAL calling
DCEFCLK DS message to SMU on clk init.
[How]
Call DCEFCLK DS message to SMU on clk init.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Chris Park <Chris.Park@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
If some SMU features are not enabled, SMU will return fail to that
message.
[HOW]
SMU_TIMEOUT macro will treat "return fail" as timeout also.
Correct the macro to only report timeout case.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Ian Chen <ian.chen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
As part of the FPU isolation work documented in
https://patchwork.freedesktop.org/series/93042/, isolate
code that uses FPU in DCN302 to DML, where all FPU code
should locate.
Co-authored-by: Jasdeep Dhillon <jdhillon@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Jasdeep Dhillon <jdhillon@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This version brings improvements in the following:
- Drop unnecessary DCN guards
- Improve Z9 interface
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Need to disable Z9 on configurations that only support Z10
[How]
Support new PMFW interface to disable Z9
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Might potentially have truncation problem with the implicit casting
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
- We only ever want seamless boots on eDPs
- The naming and logic did not match the context
[HOW]
- Removed unnecessary if statements
- Renamed power_down_display_on_boot to seamless_boot_edp_requested and
swapped the logic
Reviewed-by: Martin Leung <Martin.Leung@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Jarif Aftab <jaraftab@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The WA from commit 2a50edbf10 ("drm/amd/display: Apply w/a for hard hang
on HPD") and commit 1bd3bc745e ("drm/amd/display: Extend w/a for hard
hang on HPD to dcn20") causes a regression in s0ix where the system will
fail to resume properly on many laptops. Pull the workarounds out to
avoid that s0ix regression in the common case. This HPD hang happens with
an external device in special circumstances and a new W/A will need to be
developed for this in the future.
Cc: Qingqing Zhuo <qingqing.zhuo@amd.com>
Reported-by: Scott Bruce <smbruce@gmail.com>
Reported-by: Chris Hixon <linux-kernel-bugs@hixontech.com>
Reported-by: spasswolf@web.de
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215436
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/1821
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/1852
Fixes: 2a50edbf10 ("drm/amd/display: Apply w/a for hard hang on HPD")
Fixes: 1bd3bc745e ("drm/amd/display: Extend w/a for hard hang on HPD to dcn20")
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
dpg_width is being initialized to width but this is never read
as dpg_width is overwritten later on. Remove the redundant
initialization.
Cleans up the following clang-analyzer warning:
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc_link_dp.c:6020:8:
warning: Value stored to 'dpg_width' during its initialization is never
read [clang-analyzer-deadcode.DeadStores].
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Those APIs are used only by legacy ASICs(si/kv). They cannot be
shared by other ASICs. So, we create a new holder for them.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Display is another client of our power APIs. It's not proper to spike
into power implementation details there.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why&How]
Freesync Video Mode is a experimental feature previously,
and need to be enabled by kernel parameter. We enable it
by default with removing module paramterter in amdgpu_dm.
v2: squash the patches together
Signed-off-by: Solomon Chiu <solomon.chiu@amd.com>
Reviewed-by: Aurabindo Jayamohanan Pillai <Aurabindo.Pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The function performs a check on the "adev" input parameter, however, it
is used before the check.
Initialize the "dev" variable after the sanity check to avoid a possible
NULL pointer dereference.
Fixes: e27c41d5b0 ("drm/amd/display: Support for DMUB HPD interrupt handling")
Addresses-Coverity-ID: 1493909 ("Null pointer dereference")
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: José Expósito <jose.exposito89@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Otherwise future commands may fail as well leading to downstream
problems that look like they stemmed from a timeout the first time
but really didn't.
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When UBSAN is enabled a case is shown on unplugging the display that
this variable hasn't been initialized by `update_dsc_caps`, presumably
when the display was unplugged it wasn't copied from the DPCD.
Link: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1956497
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
To maintain compatibility with firmware older than 4.0.11.
Those firmware may have interrmittent hangs with RDCSPIPE or the PHY,
but we shouldn't regress their previous behavior.
[How]
Use the new path if firmware is development or 4.0.11 or newer. Use the
legacy path otherwise.
Fixes: 41f91315b5 ("drm/amd/display: Query DMCUB for dp alt status")
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Hansen Dsouza <hansen.dsouza@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
We want to know if new crtc state is enabling MPO configuration before
enabling it.
[how]
Detect if both primary and overlay planes are enabled on the same CRTC.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
driver missed the check.
[how]
add the check.
add min display clock = 100mhz check based on dccg doc.
[note]
add SetPhyclkVoltageByFreq as confirmed with smu, but not enabled in
this change.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
PSP will suspend and resume DMCUB. Driver should just wait for DMCUB to
finish the auto load before continuining instead of placing it into
reset, wiping its firmware state and reinitializing.
If we don't let DMCUB fully finish initializing for S0ix then some state
will be lost and screen corruption can occur due to incorrect address
translation.
[How]
Use dmub_srv callbacks to determine in DMCUB is running and wait for
auto-load to complete before continuining.
In S0ix DMCUB will be running and DAL fw so initialize will skip.
In S3 DMCUB will not be running and we will do a full hardware init.
In S3 DMCUB will be running but will not be DAL fw so we will also do
a full hardware init.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Mikita Lipski <Mikita.Lipski@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
1. Current code hard codes link to PHY mapping in dc link level per asic
per revision.
This is not scalable. In long term the mapping will be obatined from
DMUB and store in dc resource.
2. Depending on DCN revision and endpoint type, the definition of
dio_output_idx dio_output_type and phy_idx are not consistent. We need
to unify the meaning of these hardware indices across different system
configuration.
[how]
1. Temporarly move the hardcoded mapping to dc_resource level, which
should have full awareness of asic specific configuration and add a TODO
comment to move the mapping to DMUB.
2. populate dio_output_idx/phy_idx for all configuration, define
usb4_enabled bit instead of dio_output_type as an external enum.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Eric Yang <Eric.Yang2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Depend on res_pool->res_cap->num_timing_generator to query timing
gernerator information, it would case underflow at the fused display
pipes case.
Due to the res_pool->res_cap->num_timing_generator records default
timing generator resource built in driver, not the current chip.
[How]
Some ASICs would be fused display pipes less than the default setting.
In dcnxx_resource_construct function, driver would obatin real timing
generator count and store it into res_pool->timing_generator_count.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Yi-Ling Chen <Yi-Ling.Chen2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The "plane_state" pointer was access before checking if it was NULL.
Avoid a possible NULL pointer dereference by accessing the plane
address after the check.
Addresses-Coverity-ID: 1493892 ("Dereference before null check")
Fixes: 3f68c01be9 ("drm/amd/display: add cyan_skillfish display support")
Signed-off-by: José Expósito <jose.exposito89@gmail.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In function enable_stream_features(), the variable "old_downspread.raw"
could be uninitialized if core_link_read_dpcd() fails, however, it is
used in the later if statement, and further, core_link_write_dpcd()
may write random value, which is potentially unsafe.
Fixes: 6016cd9dba ("drm/amd/display: add helper for enabling mst stream features")
Cc: stable@vger.kernel.org
Signed-off-by: Yizhuo Zhai <yzhai003@ucr.edu>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
When reboot the link res map should be persisted. So during boot up,
driver will look at the map to determine which link should take priority
to use certain link res. This is to ensure that link res remains
unshuffled after a reboot.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
When there are more DP2.0 RXs connected than the number HPO DP link
encoders we have, we need to dynamically allocate HPO DP link encoder to
the port that needs it.
[how]
Only allocate HPO DP link encoder when it is needed.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Update all accesses to use hpo dp link encoder through link resource
only.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
This commit is to populate link res in preparation of the next commit.
The next commit will replace all existing code to use link res instead
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
There will be a series of re-arch changes in Link Resource Management.
They are more and more muxable link resource objects and the resource is
insufficient for a one to one allocation to all links created.
Therefore a link resource sharing logic is required to determine which
link should use certain link resource.
This commit is the first one in this series that starts by defining a
link resource struct, this struct will be available to all interfaces
that need to perform link programming sequence.
In later commits, we will granduately decouple link resource objects out
of dc link. So instead of access a link resource from dc link. Current
link's resource can be accessible through pipe_ctx->link_res during
commit, or by calling dc_link_get_cur_link_res function with current
link passed in after commit.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This version brings along the following:
- Fixes and improvements in the LTTPR code
- Improve z-state
- Fix null pointer check
- Improve communication with s0i2
- Update multiple-display split policy
- Add missing registers
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
These registers are currently missing from the DCN303 header files
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: George Shen <George.Shen@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We'll exit optimized power state to do link detection but we won't enter
back into the optimized power state.
This could potentially block s2idle entry depending on the sequencing,
but it also means we're losing some power during the transition period.
[How]
Hook up the handler like DCN21. It was also missed like the
exit_optimized_pwr_state callback.
Fixes: 64b1d0e8d5 ("drm/amd/display: Add DCN3.1 HWSEQ")
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Eric Yang <Eric.Yang2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DP spec specifies that DPRX shall use the read interval in the
TRAINING_AUX_RD_INTERVAL_PHY_REPEATER LTTPR DPCD register. This
register's bit definition is the same as the AUX read interval register
for DPRX.
[How}
Remove logic which forces AUX read interval to 100us for repeaters when
in LTTPR non-transparent mode.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Wesley Chalmers <wesley.chalmers@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: George Shen <George.Shen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Otherwise SMU won't mark Display as idle when trying to perform s2idle.
[How]
Mark the bit in the dcn31 codepath, doesn't apply to older ASIC.
It needed to be split from phy refclk off to prevent entering s2idle
when PSR was engaged but driver was not ready.
Fixes: 118a331516 ("drm/amd/display: Add DCN3.1 clock manager support")
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Eric Yang <Eric.Yang2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Bug fix for null function ptr (should check for NULL instead of not
NULL)
[How]
Fix if condition
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Samson Tam <samson.tam@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The change of setting a timer callback on boot for 10 seconds is still
working, just lacked power down for DCN10.
[How]
Added power down for DCN10.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Derek Lai <Derek.Lai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Stutter period won't be less than 5000.0, but if PSR is enabled then we
can potentially enter Z9 when MPO is enabled.
SMU will try to enter Z9 too early in these cases (before PSR is
enabled) and we'll see underflow.
[How]
Block z-states (z9, z10) until we can add a new interface to SMU to
signal when we can support z10 but not z9.
We can revert this once the interface change is in.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Eric Yang <Eric.Yang2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Current implementation is not scalable and retrofits the existing
standard link training code for purposes outside of its original design.
[How]
Refactor vendor specific link training sequence into its own separate
function to be called instead of the standard link training function.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: George Shen <George.Shen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Max link rate should be limited to the maximum link rate support by any
LTTPR that are connected, including when operating in transparent mode.
[How]
Include transparent mode when factoring in LTTPR max supported link
rate.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Wesley Chalmers <wesley.chalmers@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: George Shen <George.Shen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
B0 PHY C map to F, D map to G driver use logic instance, dmub does the
remap. Driver still need use the right PHY instance to access right HW.
[how]
use phyical instance when program PHY register.
[note]
could move resync_control programming to dmub next.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
A porting error on a previous patch left the block of code that
causes the crash from a NULL pointer dereference.
More specifically, we try to access link_enc before it's assigned in
the USB4 case in the following assignment:
config.dio_output_idx = link_enc->transmitter - TRANSMITTER_UNIPHY_A;
[How]
That assignment occurs later depending on the ASIC version. It's only
needed on DCN31 and only after link_enc is already assigned.
Fixes: 986430446c ("drm/amd/display: fix a crash on USB4 over C20 PHY")
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
