DC was using compile time initialization of register addresses using
SR_* macros and their variants. These have been converted to use runtime
initialization.
The REG_STRUCT macro is a definition that is added to SR_* macros.
During initialization, this must be defined before SR_* macros are
invoked, which are in turn invoked through various IP initialization macros.
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Brian Chang <Brian.Chang@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Retrying on receiving a NACK can result in long overall EDID read times
in some cases.
[How]
Retry only on DEFER and return immediately on NACK.
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Brian Chang <Brian.Chang@amd.com>
Signed-off-by: Ilya Bakoulin <Ilya.Bakoulin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Reprogramming the stream despite no changes in ODM combine mode.
Reprogramming the stream would cause intermittent black screen on
display which could only be recovered through enable/disable sequence.
[HOW]
Fixed bug where we detected a change in ODM combine mode despite ODM
combine mode being disabled. Also removed code which required stream to
be reprogrammed once a change in ODM combine mode was noticed. Lastly we
do not support dynamic ODM switching for HDMI TMDS and FRL on DCN32,
therefore we never want to change its ODM policy.
Reviewed-by: Samson Tam <Samson.Tam@amd.com>
Acked-by: Brian Chang <Brian.Chang@amd.com>
Signed-off-by: Saaem Rizvi <SyedSaaem.Rizvi@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
odm 2:1 policy is splitting the pipes in 4k144.
then in subvp code, we merge the pipes. but since the
configuration is unsupported, we keep the pipes split
[How]
for unsupported subvp configuration, redo the dml and
pipe split calls
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Brian Chang <Brian.Chang@amd.com>
Signed-off-by: Samson Tam <samson.tam@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
RV2 do not change pipe split policy in the
minimal pipe split transition state.
This will unblock mode support on some
parts that limit to DPM0 for power reason.
[How]
Do not change pipe split policy in the
minimal pipe split transition state to
allow 4k multi display configs to be
supported at DPM0.
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Brian Chang <Brian.Chang@amd.com>
Signed-off-by: Derek Lai <Derek.Lai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This verion brings along following fixes:
-Add scaling factor for SubVP
-Modify stop_dbg_mode return value
-Add gfx_off members and document
-Add GFXOFF function for vangogh
-Add GFXOFF stats to debug
-Fix codestyle problems
-Fix overflow on MIN_I64
-Fix Unneeded semicolon
-Fix comment typo
-Remove useless condition in amdgpu_job_stop_all_jobs_on_sched()
-Add decoder_iv_ts helper for ih_v6
-Add chip version to DCN32
-Avoid doing vm_init multiple time
-Modify size calculation in MALL
-Fix DSC for phantom pipes
-Update clock table policy for DCN314
-Modify header inclusion pattern
-Fix plug/unplug external monitor will playback MPO video
-Add debug parameter to retain default clock table
-Increase tlb flush timeout for sriov
-Fix compare intergers of different widths
-Add reserved dc_log_type
-Fix pixel clock programming
Acked-by: Brian Chang <Brian.Chang@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Removes DEFINEs that should have been removed after they were
introduced to ObjectID.h by the commit abea57d70e
("drm/amdgpu: Add BRACKET_LAYOUT_ENUMs to ObjectID.h")
Signed-off-by: Tales Aparecida <tales.aparecida@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DCN314 supports PCON.
[How]
Explicitly enable it in dcn314 resources.
Signed-off-by: Roman Li <roman.li@amd.com>
Reviewed-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
dml_wrapper* files were removed in commit 01b537eeb0
("drm/amd/display: Remove unused code"), as they are not used anywhere.
However, the header file wasn't removed, so remove the header as well.
Signed-off-by: Magali Lemes <magalilemes00@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Semicolon is not required after curly braces.
Link: https://bugzilla.openanolis.cn/show_bug.cgi?id=1918
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Addresses the following warning:
drivers/gpu/drm/amd/amdgpu/../display/dc/dml/dcn30/display_mode_vba_30.c:3596:6: error: stack frame size (2092) exceeds limit (2048) in 'dml30_ModeSupportAndSystemConfigurationFull' [-Werror,-Wframe-larger-than]
void dml30_ModeSupportAndSystemConfigurationFull(struct display_mode_lib *mode_lib)
^
UseMinimumDCFCLK() is eating away at
dml30_ModeSupportAndSystemConfigurationFull()'s stack space, so use a
pointer to struct vba_vars_st instead of passing lots of large arrays
as parameters by value.
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes five checkpatch warnings:
CHECK: Please don't use multiple blank lines
+
+
ERROR: Macros with complex values should be enclosed in parentheses
+#define MAX_I64 \
+ (int64_t)((1ULL << 63) - 1)
WARNING: Missing a blank line after declarations
+ struct bw_fixed res;
+ ASSERT(value < BW_FIXED_MAX_I32 && value > BW_FIXED_MIN_I32);
ERROR: that open brace { should be on the previous line
+ do
+ {
ERROR: that open brace { should be on the previous line
+ if (remainder >= arg2_value)
+ {
Signed-off-by: Tales Aparecida <tales.aparecida@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The definition of MIN_I64 in bw_fixed.c can cause gcc to whinge about
integer overflow, because it is treated as a positive value, which is
then negated. The temporary positive value is not necessarily
representable.
This causes the following warning:
../drivers/gpu/drm/amd/amdgpu/../display/dc/dml/calcs/bw_fixed.c:30:19:
warning: integer overflow in expression ‘-9223372036854775808’ of type
‘long long int’ results in ‘-9223372036854775808’ [-Woverflow]
30 | (int64_t)(-(1LL << 63))
| ^
Writing out (-MAX_I64 - 1) works instead.
Signed-off-by: David Gow <davidgow@google.com>
Signed-off-by: Tales Aparecida <tales.aparecida@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The double `aligned' is duplicated in line 1070, remove one.
Signed-off-by: min tang <tangmin@cdjrlc.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We have some old code associated with DML, which we had plans to use,
but at some point, we just moved away from it. This commit removes the
dml_wrapper* files since they are not used anymore.
Reported-by: Magali Lemes <magalilemes00@gmail.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Currently, we are using soc._clock_tmp[] to temporarily store and modify
data from soc.clock_limits[] before copying it back into
soc.clock_limits[] (because modifying data directly in
soc.clock_limits[] causes unintended behavior). However, this approach
has a number of downsides, such as:
1. struct _vcs_dpi_soc_bounding_box_st's creation/destruction
aren't well defined (which could mean more unintended
behavior).
2. Throwing "temp" varibles in structs everywhere doesn't make
for a particularly readable codebase.
For these reasons, we should get rid of soc._clock_tmp[] by defining a
struct scratch within struct dc that, contains within it all of the
temporary variables (including _clock_tmp[]) such that it is obvious how
they are intended to be used.
Co-authored-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Describe structs and enums used to set blend mode properties to MPC
blocks. Some pieces of information are already available as code
comments, and were just formatted. Others were collected and summarised
from discussions on AMD issue tracker[1][2].
[1] https://gitlab.freedesktop.org/drm/amd/-/issues/1734
[2] https://gitlab.freedesktop.org/drm/amd/-/issues/1769
v2:
- fix typos (Tales)
- add MPCC to MPC entry in the glossary
Signed-off-by: Melissa Wen <mwen@igalia.com>
Reviewed-by: Tales Aparecida <tales.aparecida@gmail.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add details about color correction capabilities and explain a bit about
differences between DC hw generations and also how they are mapped
between DRM and DC interface. Two schemas for DCN 2.0 and 3.0 (converted
to svg from the original png) is included to illustrate it. They were
obtained from a discussion[1] in the amd-gfx mailing list.
[1] https://lore.kernel.org/amd-gfx/20220422142811.dm6vtk6v64jcwydk@mail.igalia.com/
v1:
- remove redundant comments (Harry)
- fix typos (Harry)
v2:
- reword introduction of color section
- add co-dev tag for Harry - who provided most of the info
- fix typos (Tales)
- describe missing struct parameters (Tales and Siqueira)
Co-developed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Melissa Wen <mwen@igalia.com>
Reviewed-by: Tales Aparecida <tales.aparecida@gmail.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The timing programming inside DCN is far from trivial, it has multiple
parameters associated with that, and the lack of documentation does not
help comprehend this already complicated topic. This commit tries to
improve this situation by expanding the documentation of dc_crtc_timing
and the VTG program function.
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In the DCN code, we can find some references to three different pipe
split policies but no clear description. This commit adds some
kernel-doc that explains more about these options and a little bit of
their impact.
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
For SubVP scaling cases, we must include the scaling
info as part of the cmd. This is required when converting
OTG line to HUBP line for the MALL_START_LINE programming.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Brian Chang <Brian.Chang@amd.com>
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
this is to ensure that driver will not reprogram hvm_prefetch_req again if
it is done.
Reviewed-by: Martin Leung <Martin.Leung@amd.com>
Acked-by: Brian Chang <Brian.Chang@amd.com>
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
Use pitch when calculating size to cache in MALL
Reviewed-by: Samson Tam <Samson.Tam@amd.com>
Acked-by: Brian Chang <Brian.Chang@amd.com>
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
Don't set DSC bit for phantom pipes, not
required since phantom pipe don't have
any actual output
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Brian Chang <Brian.Chang@amd.com>
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Depending on how the clock table is constructed from PMFW we can run
into issues where we don't think we have enough bandwidth available
due to FCLK too low - eg. when the FCLK table contains invalid entries
or a single entry.
We should always pick up the maximum clocks for each state as a final
state in this case to prevent validation from failing if the table is
malformed.
We should also contain sensible defaults in the case where values
are invalid.
Redfine the clock table structures by adding a 314 prefix to make
debugging these issues easier by avoiding symbol name clashes.
Overall this policy more closely aligns to how we did things for 315,
but because of how the voltage rail is setup we should favor keeping
DCFCLK low rather than DISPCLK or DPPCLK - so use the max for those
in every entry.
Reviewed-by: Daniel Miess <daniel.miess@amd.com>
Acked-by: Brian Chang <Brian.Chang@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Recent backport from opensource broke the Nightly tool build
that tests DC and DML for bugs and regressions. This was
because the backport had a header inclusion that was not
consistent with the AMD style of including headers was allowed
to be merged back in DML code that caused tool compilation
failures.
[How]
Modify the way in which the header file in included so that it
is consistent with AMD style of including headers. This then
automatically fixes the tool compilation process and also
helps maintain the code quality and consistency.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Brian Chang <Brian.Chang@amd.com>
Signed-off-by: Chaitanya Dhere <chaitanya.dhere@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Pipes for MPO primary and overlay will be power down and power up during
plug/unplug external monitor while MPO video playback.
But the pipes were the same after plug/unplug and should not need to be
power down and power up or it will make page flip interrupt disabled and
cause hang issue.
[How]
Add pipe split change condition that not only check the top pipe pointer
but also check the index of top pipe if both top pipes are available.
Reviewed-by: Sun peng Li <Sunpeng.Li@amd.com>
Acked-by: Brian Chang <Brian.Chang@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Need a way to retain default clock table to aid
the investigation into why 8k@30 display not
lighting up on dcn314
[How]
Use flag to prevent execution of bw_params helper
function and function for updating bw_bounding_box
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Brian Chang <Brian.Chang@amd.com>
Signed-off-by: Daniel Miess <Daniel.Miess@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Increase width of some variables to avoid comparing integers of
different widths.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Acked-by: Brian Chang <Brian.Chang@amd.com>
Signed-off-by: Josip Pavic <Josip.Pavic@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some pixel clock values could cause HDMI TMDS SSCPs to be misaligned
between different HDMI lanes when using YCbCr420 10-bit pixel format.
BIOS functions for transmitter/encoder control take pixel clock in kHz
increments, whereas the function for setting the pixel clock is in 100Hz
increments. Setting pixel clock to a value that is not on a kHz boundary
will cause the issue.
[How]
Round pixel clock down to nearest kHz in 10/12-bpc cases.
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Brian Chang <Brian.Chang@amd.com>
Signed-off-by: Ilya Bakoulin <Ilya.Bakoulin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This version brings along following fixes:
-Fix edp panel missing event
-Set ARGB16161616 pixel format to 26
-Fix dcn32 interger issue
-Clear optc underflow bit after ODM clock off
-Fix issue with stereo3D
-Fix DML2 lightup issue
-Correct DTBCLK for dcn314
-Revert for a regression
-Fix clocks and bugs in DML2
-Enable SubVP by defalut on DCN32 & DCN321
-Corret boundary condition for engin ID on DCN303
-Fix FRL encoder override registry key
-Fix VPG for dcn314 HPO
-Fix Linux compile-time warning
-Add new prefetch modes in DML for DCN32
Acked-by: Brian Chang <Brian.Chang@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Limiting vscsdp_for_colorimetry for YCbCr420/BT2020 resulted in red/green
point failures in HDR10 DTN tests. The re-implementation of ARGB16161616
was to fix this however it did not actually fix this issue but a side effect of the
issue.
[HOW]
Change ARGB16161616 pixel format to 26.
Reviewed-by: Martin Leung <Martin.Leung@amd.com>
Acked-by: Brian Chang <Brian.Chang@amd.com>
Signed-off-by: Ethan Wellenreiter <Ethan.Wellenreiter@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This version brings along following fixes:
- Move fpu file to dml folder
- Fix CAB allocation for multiple displays
- Add a variable to update FCLK
- Fix TMDS 4K@60Hz YCbCr420 corruption issue
- Fix MPC tree infinite loop in some case
- Fix HDMI VSIF V3 blank screen issue
- Add some documentation to the code
- Allow alternate prefetch modes in DML for DCN32
- Fix VPG instancing for dcn314 HPO
- Check correct bounds for stream encoder instances for DCN303
- Enable SubVP by default on DCN32 & DCN321
- Fix DTBCLK not correct for dcn314
- Fix Compile-time warning
- Fix the stereo mode hang issue
- Fix display light up issue
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
SUBVP_START_LINE must be aligned to 2 swaths, so add
16 lines of margin so the start line can be adjusted by
up to 16 lines for alignment purposes in FW.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
After TDR recovery, eDP and USB4 display does not light up. Because
dmub outbox notifications are not enabled after dmub reload and link
encoder assignments for the streams are not cleared before dc state
reset.
[How]
- Dmub outbox notification is enabled after tdr recovery by issuing
inbox command to dmub.
- Link encoders for the streams are unassigned before dc state reset.
Reviewed-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
After ODM clock off, optc underflow bit will be kept there always and clear not work.
We need to clear that before clock off.
[How]
Clear that if have when clock off.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Fudong Wang <Fudong.Wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
MALL not supported with stereo3D according
to DCN doc.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
Observed in stereomode that programming FLIP_LEFT_EYE
can cause hangs. Keep FLIP_ANY_FRAME in stereo mode so
the surface flip can take place before left or right eye
Reviewed-by: Martin Leung <Martin.Leung@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
Reverts commit "attempt to fix the logic in commit_planes_for_stream()"
since it caused a regression.
Reviewed-by: Martin Leung <Martin.Leung@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DTBCLK clocks reset after clocks are initialized
and bounding box values are also incorrect.
[How]
Use dcn31 init clock function programming sequence
and correct bounding box values for dcn314
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Duncan Ma <duncan.ma@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why&How]
Set the debug options to enable SubVP feature
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
eng_id for DCN303 cannot be more than 1, since we have only two
instances of stream encoders.
Check the correct boundary condition for engine ID for DCN303 prevent
the potential out of bounds access.
Fixes: cd6d421e3d ("drm/amd/display: Initial DC support for Beige Goby")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: stable@vger.kernel.org
Reviewed-by: Chris Park <Chris.Park@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
An issue during VPG indexing offset generation causing
to use the incorrect VPG. HW team placed VPG instances
5 at end of list, making it VPG 9 in register headers.
[How]
Correct VPG instance for HPO encoders.
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Duncan Ma <duncan.ma@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixed bracketing around condition statement.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: David Galiffi <David.Galiffi@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Driver is restricting voltage levels if system cannot switch
in vblank.
[How]
Change allow_for_pstate_or_stutter_in_vblank_final from
dm_prefetch_support_uclk_fclk_and_stutter to
dm_prefetch_support_uclk_fclk_and_stutter_if_possible.
Add support for a new registry property,
DalDMLDisallowAlternatePrefetchModes, for easier debugging.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: David Galiffi <David.Galiffi@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In some cases MPC tree bottom pipe ends up point to itself. This causes
iterating from top to bottom to hang the system in an infinite loop.
[How]
When looping to next MPC bottom pipe, check that the pointer is not same
as current to avoid infinite loop.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Josip Pavic <Josip.Pavic@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
