[WHY]
Assert statements causing several bugs on Linux DM
[HOW]
Removing assert statement for Linux DM
(ASSERT(result == VBIOSSMC_Result_OK)). Also adding
logging statements for setting dcfclk.
Bug: https://bugzilla.kernel.org/show_bug.cgi?id=216092
Fixes: c1b972a18d ("drm/amd/display: Insert pulling smu busy status before sending another request")
Reviewed-by: Gabe Teeger <Gabe.Teeger@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Saaem Rizvi <SyedSaaem.Rizvi@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Logging for SMU response value after the wait allows us to know
immediately what the response value was. Makes it easier to debug should
the value be anything other than OK.
[HOW]
Using the the already available DC SMU logging functions.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Saaem Rizvi <SyedSaaem.Rizvi@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit 8440f57532.
Causes a hang when hotplugging DP, shutting down system, or
enabling dual eDP.
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
ref_dtbclk value is assigned in clk_mgr_construct,
but the clks struct is cleared in init_clocks.
Make sure to restore the value or we will get
0 value for ref_dtbclk in DCN31.
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Jasdeep Dhillon <jdhillon@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When enabling an HPO stream for the first time after having previously
enabled a DIO stream there may be lingering DIO FIFO errors even though
the DIO is no longer enabled.
These can cause display clock change to hang if we don't apply the
OTG disable workaround since the ramping logic is tied to OTG on.
[How]
The workaround wasn't being applied in the sequence of:
1 DIO stream
0 streams
1 HPO stream
because current_state has no stream or planes in its context - and
it's only swapped after optimize has finished.
We should be using the incoming context instead to determine whether
this logic is needed or not.
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Jasdeep Dhillon <jdhillon@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
why and how:
Revert this change. It was causing a black screen with certain blocks
Reviewed-by: George Shen <George.Shen@amd.com>
Acked-by: Jasdeep Dhillon <jdhillon@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Leung, Martin <Martin.Leung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
It's not used outside of dcn31_clk_mgr.c.
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
In headless systems, if SetMode/Power down timer
is not called, hardware will not be powered down
causing HW/SW discrepancies. Powering down hardware
on SetPowerState to D3 will ensure SW/HW state is accurate.
[HOW]
1. If PowerDownThread timer is not trigger but OS call
SetPowerState to D3, power down hardware.
2. Update HDMI hang w/a to apply to all TMDS signals on
headless system
Reviewed-by: Martin Leung <Martin.Leung@amd.com>
Acked-by: Pavle Kotarac <Pavle.Kotarac@amd.com>
Signed-off-by: Paul Hsieh <paul.hsieh@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: George Shen <George.Shen@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Martin Leung <Martin.Leung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
In headless systems, if SetMode/Power down timer
is not called, hardware will not be powered down
causing HW/SW discrepancies. Powering down hardware
on SetPowerState to D3 will ensure SW/HW state is accurate.
[HOW]
If PowerDownThread timer is not trigger but OS call
SetPowerState to D3, power down hardware.
Reviewed-by: Eric Yang <Eric.Yang2@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Paul Hsieh <paul.hsieh@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why&How]
add debug option to bypass ssinfo from bios.
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The original latencies were causing underflow in some modes.
Resolution: 2880x1620@60p when HDR enable
[How]
1. Replace with the up-to-date watermark values based on new measurments
2. Correct the ddr_wm_table name to DDR5 on DCN31
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Signed-off-by: Paul Hsieh <paul.hsieh@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
A number of BIOS versions have a problem with the watermarks table not
being configured properly. This manifests as a very scary looking warning
during resume from s0i3. This should be harmless in most cases and is well
understood, so decrease the assertion to a clearer warning about the problem.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
To help triage issues and coordinate driver/bios release dependency
[How]
Only enable the new Z9 interface when debug option is set, otherwise
treat Z10 only support case as Zstate disallowed.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Need to disable Z9 on configurations that only support Z10
[How]
Support new PMFW interface to disable Z9
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Otherwise future commands may fail as well leading to downstream
problems that look like they stemmed from a timeout the first time
but really didn't.
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Otherwise SMU won't mark Display as idle when trying to perform s2idle.
[How]
Mark the bit in the dcn31 codepath, doesn't apply to older ASIC.
It needed to be split from phy refclk off to prevent entering s2idle
when PSR was engaged but driver was not ready.
Fixes: 118a331516 ("drm/amd/display: Add DCN3.1 clock manager support")
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Eric Yang <Eric.Yang2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This turns previously global functions into static, thus removing
compile-time warnings such as:
warning: no previous prototype for 'get_highest_allowed_voltage_level'
[-Wmissing-prototypes]
742 | unsigned int get_highest_allowed_voltage_level(uint32_t chip_family, uint32_t hw_internal_rev, uint32_t pci_revision_id)
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
warning: no previous prototype for 'rv1_vbios_smu_send_msg_with_param'
[-Wmissing-prototypes]
102 | int rv1_vbios_smu_send_msg_with_param(struct clk_mgr_internal *clk_mgr, unsigned int msg_id, unsigned int param)
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Changes since v1:
- As suggested by Rodrigo Siqueira:
1. Rewrite function signatures to make them more readable.
2. Get rid of unused functions in order to remove 'defined but not
used' warnings.
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Isabella Basso <isabbasso@riseup.net>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
On certain configs, SMU clock table voltages don't match which cause parser
to behave incorrectly by leaving dcfclk and socclk table entries unpopulated.
[HOW]
Currently the function that finds the corresponding clock for a given voltage
only checks for exact voltage level matches. In the case that no match gets
found, parser now falls back to searching for the max clock which meets the
requested voltage (i.e. its corresponding voltage is below requested).
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
The original latencies were causing underflow in some modes
[how]
Replace with the up-to-date watermark values based on new measurments
Reviewed-by: Ahmad Othman <ahmad.othman@amd.com>
Acked-by: Agustin Gutierrez Sanchez <agustin.gutierrez@amd.com>
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Disable root clock for dpp when not being used.
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Agustin Gutierrez Sanchez <agustin.gutierrez@amd.com>
Signed-off-by: Jake Wang <haonan.wang2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When system is in Z10 HPD interrupts cannot fire, we may miss display
configuration changes.
[How]
When Zstate is enabled, if DMUB indicate DCN has lost power, do a
complete detection periodically.
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Assuming DIG link encoders are statically mapped to links can cause
system instability due to null pointer accesses.
[How]
- Add checks for non-null link encoder pointers before trying to access
them.
- When a hardware platform uses dynamic DIG assignment (i.e. resource
function 'link_encs_assign' defined) and a link supports flexible
mapping to DIGs, use the link_enc_cfg API to access the DIG assigned to
a link or stream.
Reviewed-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Acked-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
PMFW message which previously thought to only control Z9 controls both
Z9 and Z10. Also HW design team requested that Z9 must only be supported
on eDP due to content protection interop.
[How]
Change zstate support condition to match updated policy
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Hardcoding the VCO frequency isn't correct since we don't own or control
the value.
In the case where the hardcode is also missing we can't lightup display.
[How]
Query from the CLK register instead. Update the DFS frequency to be able
to compute the VCO frequency.
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When requesting clocks from SMU which takes MHz inputs, DC will round
down KHz when converting to MHz, thus potentially requesting too low a
clock value.
[How]
Round up (ceil) when converting KHz to MHz for clock requests to SMU.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Adds support for clock requests for the various parts of the DCN3.1 IP
and the interfaces and definitions for sending messages to SMU/PMFW.
Includes new support for z9/10, detecting SMU timeout and p-state
support enablement.
Acked-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
