[Why]
Newer DCN should use optc3
[How]
Declare optc3 vmin/vmax function in header.
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Most of the time, a single display uses the ODM combine. When using
multi-display, we use ODM combine only if it is necessary. These cases
are not flexible enough for us, and we can improve them to take
advantage of our hardware. We want to have more control over the ODM
policy.
[How]
This commit add a new debug flag named
enable_single_display_2to1_odm_policy to control the ODM policy and
another flag named enable_dp_dig_pixel_rate_div_policy to fine control
the ODM combine. This is possible by adding a new "pipe.dest" parameter
that can be set to ODM 2:1 combined if we use a single display. For
dynamic ODM combine, when using DP-DIG, DCN applies K2=2 settings for
ODM combine. Note that this feature affects the following registers:
- timing.pix_clk_100khz -> DP_VID_M, DP_VID_N
- requested_pix_clk_100hz -> DP_DTOn_PHASE
- OTGn_PIXEL_RATE_DIVK2
- DP_PIXEL_PER_CYCLE_PROCESSING_MODE
- DIG_FIFO_OUTPUT_PIXEL_MODE
- DP_VID_N_MUL
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Samson Tam <Samson.Tam@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add function to set pixels per cycle in DIG stream encoder
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Eric Bernstein <eric.bernstein@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]:
Lut pipeline will be hooked up differently in some asics
need to add new interfaces and missing registers.
[HOW]:
Add missing registers and hook up programming from DPP for pre-blend
lut.
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Martin Leung <Martin.Leung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This commit enables the SubVP feature. To achieve that, we need to:
- Don't force p-state disallow on SubVP (can't block dummy p-state)
- Send calculated watermark to DMCUB for SubVP
- Adjust CAB mode message to PMFW
- Add a proper locking sequence for SubVP
- Various fixes to SubVP static analysis and determining SubVP config
- Currently SubVP not supported with pipe split so merge all pipes
before setting up SubVp
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Alan Liu <HaoPing.Liu@amd.com>
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
New dividers in DCCG need to be programmed depending
on encoder/stream type since pixels per clock in
OTG/DIO is different
DIO also needs additional programming depending on
pixels per clock
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Add core DC support for DCN 3.2.x.
v2: squash in fixup (Alex)
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
