If for some reason the msm_dp_config::descs array starts from non-zero
index or contains the hole, setting the msm_dp_config::num_descs might
be not that obvious and error-prone. Use ARRAY_SIZE to set this field
rather than encoding the value manually.
Reported-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/491399/
Link: https://lore.kernel.org/r/20220627165413.657142-1-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
We don't need to stash the encoder here. Instead we can simply pass it
around as an argument.
Cc: Kuogee Hsieh <quic_khsieh@quicinc.com>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/491187/
Link: https://lore.kernel.org/r/20220625002811.3225344-1-swboyd@chromium.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Make dp_connector_mode_valid() return precise MODE_CLOCK_HIGH rather
than generic MODE_BAD in case the mode clock is higher than
DP_MAX_PIXEL_CLK_KHZ (675 MHz).
Reviewed-by: Kuogee Hsieh<quic_khsieh@quicinc.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/489554/
Link: https://lore.kernel.org/r/20220615115920.6768-1-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Display resolution change is implemented through drm modeset. Older
modeset (resolution) has to be disabled first before newer modeset
(resolution) can be enabled. Display disable will turn off both
pixel clock and main link clock so that main link have to be
re-trained during display enable to have new video stream flow
again. At current implementation, display enable function manually
kicks up irq_hpd_handle which will read panel link status and start
link training if link status is not in sync state.
However, there is rare case that a particular panel links status keep
staying in sync for some period of time after main link had been shut
down previously at display disabled. In this case, main link retraining
will not be executed by irq_hdp_handle(). Hence video stream of newer
display resolution will fail to be transmitted to panel due to main
link is not in sync between host and panel.
This patch will bypass irq_hpd_handle() in favor of directly call
dp_ctrl_on_stream() to always perform link training in regardless of
main link status. So that no unexpected exception resolution change
failure cases will happen. Also this implementation are more efficient
than manual kicking off irq_hpd_handle function.
Changes in v2:
-- set force_link_train flag on DP only (is_edp == false)
Changes in v3:
-- revise commit text
-- add Fixes tag
Changes in v4:
-- revise commit text
Changes in v5:
-- fix spelling at commit text
Changes in v6:
-- split dp_ctrl_on_stream() for phy test case
-- revise commit text for modeset
Changes in v7:
-- drop 0 assignment at local variable (ret = 0)
Changes in v8:
-- add patch to remove pixel_rate from dp_ctrl
Changes in v9:
-- forward declare dp_ctrl_on_stream_phy_test_report()
Fixes: 62671d2ef2 ("drm/msm/dp: fixes wrong connection state caused by failure of link train")
Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Patchwork: https://patchwork.freedesktop.org/patch/489895/
Link: https://lore.kernel.org/r/1655411200-7255-1-git-send-email-quic_khsieh@quicinc.com
Signed-off-by: Rob Clark <robdclark@chromium.org>
During msm initialize phase, dp_display_unbind() will be called to undo
initializations had been done by dp_display_bind() previously if there is
error happen at msm_drm_bind. In this case, core_initialized flag had to
be check to make sure clocks is on before update DP controller register
to disable HPD interrupts. Otherwise system will crash due to below NOC
fatal error.
QTISECLIB [01f01a7ad]CNOC2 ERROR: ERRLOG0_LOW = 0x00061007
QTISECLIB [01f01a7ad]GEM_NOC ERROR: ERRLOG0_LOW = 0x00001007
QTISECLIB [01f0371a0]CNOC2 ERROR: ERRLOG0_HIGH = 0x00000003
QTISECLIB [01f055297]GEM_NOC ERROR: ERRLOG0_HIGH = 0x00000003
QTISECLIB [01f072beb]CNOC2 ERROR: ERRLOG1_LOW = 0x00000024
QTISECLIB [01f0914b8]GEM_NOC ERROR: ERRLOG1_LOW = 0x00000042
QTISECLIB [01f0ae639]CNOC2 ERROR: ERRLOG1_HIGH = 0x00004002
QTISECLIB [01f0cc73f]GEM_NOC ERROR: ERRLOG1_HIGH = 0x00004002
QTISECLIB [01f0ea092]CNOC2 ERROR: ERRLOG2_LOW = 0x0009020c
QTISECLIB [01f10895f]GEM_NOC ERROR: ERRLOG2_LOW = 0x0ae9020c
QTISECLIB [01f125ae1]CNOC2 ERROR: ERRLOG2_HIGH = 0x00000000
QTISECLIB [01f143be7]GEM_NOC ERROR: ERRLOG2_HIGH = 0x00000000
QTISECLIB [01f16153a]CNOC2 ERROR: ERRLOG3_LOW = 0x00000000
QTISECLIB [01f17fe07]GEM_NOC ERROR: ERRLOG3_LOW = 0x00000000
QTISECLIB [01f19cf89]CNOC2 ERROR: ERRLOG3_HIGH = 0x00000000
QTISECLIB [01f1bb08e]GEM_NOC ERROR: ERRLOG3_HIGH = 0x00000000
QTISECLIB [01f1d8a31]CNOC2 ERROR: SBM1 FAULTINSTATUS0_LOW = 0x00000002
QTISECLIB [01f1f72a4]GEM_NOC ERROR: SBM0 FAULTINSTATUS0_LOW = 0x00000001
QTISECLIB [01f21a217]CNOC3 ERROR: ERRLOG0_LOW = 0x00000006
QTISECLIB [01f23dfd3]NOC error fatal
changes in v2:
-- drop the first patch (drm/msm: enable msm irq after all initializations are done successfully at msm_drm_init()) since the problem had been fixed by other patch
Fixes: 570d3e5d28 ("drm/msm/dp: stop event kernel thread when DP unbind")
Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Patchwork: https://patchwork.freedesktop.org/patch/488387/
Link: https://lore.kernel.org/r/1654538139-7450-1-git-send-email-quic_khsieh@quicinc.com
Signed-off-by: Rob Clark <robdclark@chromium.org>
- Fourcc modifier for tiled but not compressed layouts
- Support for userspace allocated IOVA (GPU virtual address)
- Devfreq clamp_to_idle fix
- DPU: DSC (Display Stream Compression) support
- DPU: inline rotation support on SC7280
- DPU: update DP timings to follow vendor recommendations
- DP, DPU: add support for wide bus (on newer chipsets)
- DP: eDP support
- Merge DPU1 and MDP5 MDSS driver, make dpu/mdp device the master
component
- MDSS: optionally reset the IP block at the bootup to drop
bootloader state
- Properly register and unregister internal bridges in the DRM framework
- Complete DPU IRQ cleanup
- DP: conversion to use drm_bridge and drm_bridge_connector
- eDP: drop old eDP parts again
- DPU: writeback support
- Misc small fixes
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rob Clark <robdclark@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/CAF6AEGvJCr_1D8d0dgmyQC5HD4gmXeZw=bFV_CNCfceZbpMxRw@mail.gmail.com
Event thread supposed to exit from its while loop after kthread_stop().
However there may has possibility that event thread is pending in the
middle of wait_event due to condition checking never become true.
To make sure event thread exit its loop after kthread_stop(), this
patch OR kthread_should_stop() into wait_event's condition checking
so that event thread will exit its loop after kernal_stop().
Changes in v2:
-- correct spelling error at commit title
Changes in v3:
-- remove unnecessary parenthesis
-- while(1) to replace while (!kthread_should_stop())
Reported-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Fixes: 570d3e5d28 ("drm/msm/dp: stop event kernel thread when DP unbind")
Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Patchwork: https://patchwork.freedesktop.org/patch/484576/
Link: https://lore.kernel.org/r/1651595136-24312-1-git-send-email-quic_khsieh@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
The eDP controller does not have a reliable way keep panel
powered on to read the sink capabilities. So, the controller
driver cannot validate if a mode can be supported by the
source. We will rely on the panel driver to populate only
the supported modes for now.
Signed-off-by: Sankeerth Billakanti <quic_sbillaka@quicinc.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Patchwork: https://patchwork.freedesktop.org/patch/483313/
Link: https://lore.kernel.org/r/1650887072-16652-5-git-send-email-quic_sbillaka@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
The source device should ensure the sink is ready before proceeding to
read the sink capability or perform any aux transactions. The sink
will indicate its readiness by asserting the HPD line. The controller
driver needs to wait for the hpd line to be asserted by the sink before
it performs any aux transactions.
The eDP sink is assumed to be always connected. It needs power from the
source and its HPD line will be asserted only after the panel is powered
on. The panel power will be enabled from the panel-edp driver and only
after that, the hpd line will be asserted.
Whereas for DP, the sink can be hotplugged and unplugged anytime. The hpd
line gets asserted to indicate the sink is connected and ready. Hence
there is no need to wait for the hpd line to be asserted for a DP sink.
Signed-off-by: Sankeerth Billakanti <quic_sbillaka@quicinc.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Patchwork: https://patchwork.freedesktop.org/patch/483312/
Link: https://lore.kernel.org/r/1650887072-16652-4-git-send-email-quic_sbillaka@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
The panel-edp enables the eDP panel power during probe, get_modes
and pre-enable. The eDP connect and disconnect interrupts for the eDP/DP
controller are directly dependent on panel power. As eDP display can be
assumed as always connected, the controller driver can skip the eDP
connect and disconnect interrupts. Any disruption in the link status
will be indicated via the IRQ_HPD interrupts.
So, the eDP controller driver can just enable the IRQ_HPD and replug
interrupts. The DP controller driver still needs to enable all the
interrupts.
Signed-off-by: Sankeerth Billakanti <quic_sbillaka@quicinc.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Patchwork: https://patchwork.freedesktop.org/patch/483310/
Link: https://lore.kernel.org/r/1650887072-16652-3-git-send-email-quic_sbillaka@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
This patch adds support for generic eDP sink through aux_bus. The eDP/DP
controller driver should support aux transactions originating from the
panel-edp driver and hence should be initialized and ready.
The panel bridge supporting the panel should be ready before the bridge
connector is initialized. The generic panel probe needs the controller
resources to be enabled to support the aux transactions originating from
the panel probe.
Signed-off-by: Sankeerth Billakanti <quic_sbillaka@quicinc.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Patchwork: https://patchwork.freedesktop.org/patch/483307/
Link: https://lore.kernel.org/r/1650887072-16652-2-git-send-email-quic_sbillaka@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Two stages are required to setup up main link to be ready to transmit
video stream.
Stage 1: dp_hpd_plug_handle() perform link training to set up main link
stage 2: user space framework (msm_dp_display_enable()) to enable pixel
clock and transfer main link to video ready state.
At current implementation, when dongle unplugged dp_hdp_unplug_handle()
has to wait until stage 2 completed before it can send link down uevent
to user space framework to disable pixel clock followed by tearing down
main link. This introduce unnecessary latency if dongle unplugged happen
after stage 1 and before stage 2. It also has possibility leave main link
stay at ready state after dongle unplugged if framework does not response
to link down uevent notification. This will prevent next dongle plug in
from working. This scenario could possibly happen when dongle unplug while
system in the middle of suspending.
This patch allow unplug handle to tear down main link and notify
framework link down immediately if dongle unplugged happen after
stage 1 and before stage 2. With this approach, dp driver is much
more resilient to any different scenarios. Also redundant both
dp_connect_pending_timeout() and dp_disconnect_pending_timeout()
are removed to reduce logic complexity.
Changes in V2:
-- return -EINVAL at msm_dp_display_enable() if not in correct state
-- replace ST_CONNECT_PENDING with ST_MAINLINK_READY
Fixes: 8ede2ecc3e ("drm/msm/dp: Add DP compliance tests on Snapdragon Chipsets")
Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Patchwork: https://patchwork.freedesktop.org/patch/483391/
Link: https://lore.kernel.org/r/1650927382-22461-1-git-send-email-quic_khsieh@quicinc.com
[DB: fixed return values due to conversion to function merge]
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Current DP driver implementation, event thread is kept running
after DP display is unbind. This patch fix this problem by disabling
DP irq and stop event thread to exit gracefully at dp_display_unbind().
Changes in v2:
-- start event thread at dp_display_bind()
Changes in v3:
-- disable all HDP interrupts at unbind
-- replace dp_hpd_event_setup() with dp_hpd_event_thread_start()
-- replace dp_hpd_event_stop() with dp_hpd_event_thread_stop()
-- move init_waitqueue_head(&dp->event_q) to probe()
-- move spin_lock_init(&dp->event_lock) to probe()
Changes in v4:
-- relocate both dp_display_bind() and dp_display_unbind() to bottom of file
Changes in v5:
-- cancel relocation of both dp_display_bind() and dp_display_unbind()
Changes in v6:
-- move empty event q to dp_event_thread_start()
Changes in v7:
-- call ktheread_stop() directly instead of dp_hpd_event_thread_stop() function
Changes in v8:
-- return error immediately if audio registration failed.
Changes in v9:
-- return error immediately if event thread create failed.
Changes in v10:
-- delete extra DRM_ERROR("failed to create DP event thread\n");
Fixes: 8ede2ecc3e ("drm/msm/dp: Add DP compliance tests on Snapdragon Chipsets")
Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Reported-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Patchwork: https://patchwork.freedesktop.org/patch/482399/
Link: https://lore.kernel.org/r/1650318988-17580-1-git-send-email-quic_khsieh@quicinc.com
[DB: fixed Fixes tag]
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Since the last commit, the max_pclk_khz became constant, it's set to
DP_MAX_PIXEL_CLK_KHZ and never changed afterwards. Remove it completely
and use DP_MAX_PIXEL_CLK_KHZ directly.
Reviewed-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/480139/
Link: https://lore.kernel.org/r/20220330223008.649274-4-dmitry.baryshkov@linaro.org
[DB: applied a fix to follow connector->bridge conversion]
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Since dp_panel_get_modes() handling for dp_mode was removed,
dp_display_get_modes also doesn't change the passed dp_mode, drop the
unused dp_mode variable being allocated unused and then freed.
Reviewed-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/480137/
Link: https://lore.kernel.org/r/20220330223008.649274-3-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Since the commit ab20592759 ("drm/msm/dp: remove mode hard-coding in
case of DP CTS") the function dp_panel_get_modes() doesn't use (or fill)
the dp_mode argument. Drop it completely.
Reviewed-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/480138/
Link: https://lore.kernel.org/r/20220330223008.649274-2-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Since DRM_DEBUG_DP is deprecated in favor of drm_dbg_dp(NULL, ...),
this patch replace all DRM_DEBUG_DP with drm_dbg_dp().
Changes in v4:
-- replace (strucr drm_dev *)NULL with drm_dev
Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/474870/
Link: https://lore.kernel.org/r/1645122930-23863-4-git-send-email-quic_khsieh@quicinc.com
[DB: fixed compilation of dp_bridge_detect() caused by previous patch]
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
There is little point in having both connector and root bridge
implementation in the same driver. Move connector's functionality to the
bridge to let next bridge in chain to override it.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Sankeerth Billakanti <quic_sbillaka@quicinc.com>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/473854/
Link: https://lore.kernel.org/r/20220211224006.1797846-5-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Current DP driver implementation has adding safe mode done at
dp_hpd_plug_handle() which is expected to be executed under event
thread context.
However there is possible circular locking happen (see blow stack trace)
after edp driver call dp_hpd_plug_handle() from dp_bridge_enable() which
is executed under drm_thread context.
After review all possibilities methods and as discussed on
https://patchwork.freedesktop.org/patch/483155/, supporting EDID
compliance tests in the driver is quite hacky. As seen with other
vendor drivers, supporting these will be much easier with IGT. Hence
removing all the related fail safe code for it so that no possibility
of circular lock will happen.
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
======================================================
WARNING: possible circular locking dependency detected
5.15.35-lockdep #6 Tainted: G W
------------------------------------------------------
frecon/429 is trying to acquire lock:
ffffff808dc3c4e8 (&dev->mode_config.mutex){+.+.}-{3:3}, at:
dp_panel_add_fail_safe_mode+0x4c/0xa0
but task is already holding lock:
ffffff808dc441e0 (&kms->commit_lock[i]){+.+.}-{3:3}, at: lock_crtcs+0xb4/0x124
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #3 (&kms->commit_lock[i]){+.+.}-{3:3}:
__mutex_lock_common+0x174/0x1a64
mutex_lock_nested+0x98/0xac
lock_crtcs+0xb4/0x124
msm_atomic_commit_tail+0x330/0x748
commit_tail+0x19c/0x278
drm_atomic_helper_commit+0x1dc/0x1f0
drm_atomic_commit+0xc0/0xd8
drm_atomic_helper_set_config+0xb4/0x134
drm_mode_setcrtc+0x688/0x1248
drm_ioctl_kernel+0x1e4/0x338
drm_ioctl+0x3a4/0x684
__arm64_sys_ioctl+0x118/0x154
invoke_syscall+0x78/0x224
el0_svc_common+0x178/0x200
do_el0_svc+0x94/0x13c
el0_svc+0x5c/0xec
el0t_64_sync_handler+0x78/0x108
el0t_64_sync+0x1a4/0x1a8
-> #2 (crtc_ww_class_mutex){+.+.}-{3:3}:
__mutex_lock_common+0x174/0x1a64
ww_mutex_lock+0xb8/0x278
modeset_lock+0x304/0x4ac
drm_modeset_lock+0x4c/0x7c
drmm_mode_config_init+0x4a8/0xc50
msm_drm_init+0x274/0xac0
msm_drm_bind+0x20/0x2c
try_to_bring_up_master+0x3dc/0x470
__component_add+0x18c/0x3c0
component_add+0x1c/0x28
dp_display_probe+0x954/0xa98
platform_probe+0x124/0x15c
really_probe+0x1b0/0x5f8
__driver_probe_device+0x174/0x20c
driver_probe_device+0x70/0x134
__device_attach_driver+0x130/0x1d0
bus_for_each_drv+0xfc/0x14c
__device_attach+0x1bc/0x2bc
device_initial_probe+0x1c/0x28
bus_probe_device+0x94/0x178
deferred_probe_work_func+0x1a4/0x1f0
process_one_work+0x5d4/0x9dc
worker_thread+0x898/0xccc
kthread+0x2d4/0x3d4
ret_from_fork+0x10/0x20
-> #1 (crtc_ww_class_acquire){+.+.}-{0:0}:
ww_acquire_init+0x1c4/0x2c8
drm_modeset_acquire_init+0x44/0xc8
drm_helper_probe_single_connector_modes+0xb0/0x12dc
drm_mode_getconnector+0x5dc/0xfe8
drm_ioctl_kernel+0x1e4/0x338
drm_ioctl+0x3a4/0x684
__arm64_sys_ioctl+0x118/0x154
invoke_syscall+0x78/0x224
el0_svc_common+0x178/0x200
do_el0_svc+0x94/0x13c
el0_svc+0x5c/0xec
el0t_64_sync_handler+0x78/0x108
el0t_64_sync+0x1a4/0x1a8
-> #0 (&dev->mode_config.mutex){+.+.}-{3:3}:
__lock_acquire+0x2650/0x672c
lock_acquire+0x1b4/0x4ac
__mutex_lock_common+0x174/0x1a64
mutex_lock_nested+0x98/0xac
dp_panel_add_fail_safe_mode+0x4c/0xa0
dp_hpd_plug_handle+0x1f0/0x280
dp_bridge_enable+0x94/0x2b8
drm_atomic_bridge_chain_enable+0x11c/0x168
drm_atomic_helper_commit_modeset_enables+0x500/0x740
msm_atomic_commit_tail+0x3e4/0x748
commit_tail+0x19c/0x278
drm_atomic_helper_commit+0x1dc/0x1f0
drm_atomic_commit+0xc0/0xd8
drm_atomic_helper_set_config+0xb4/0x134
drm_mode_setcrtc+0x688/0x1248
drm_ioctl_kernel+0x1e4/0x338
drm_ioctl+0x3a4/0x684
__arm64_sys_ioctl+0x118/0x154
invoke_syscall+0x78/0x224
el0_svc_common+0x178/0x200
do_el0_svc+0x94/0x13c
el0_svc+0x5c/0xec
el0t_64_sync_handler+0x78/0x108
el0t_64_sync+0x1a4/0x1a8
Changes in v2:
-- re text commit title
-- remove all fail safe mode
Changes in v3:
-- remove dp_panel_add_fail_safe_mode() from dp_panel.h
-- add Fixes
Changes in v5:
-- to=dianders@chromium.org
Changes in v6:
-- fix Fixes commit ID
Fixes: 8b2c181e3d ("drm/msm/dp: add fail safe mode outside of event_mutex context")
Reported-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Link: https://lore.kernel.org/r/1651007534-31842-1-git-send-email-quic_khsieh@quicinc.com
Signed-off-by: Rob Clark <robdclark@chromium.org>
Widebus feature will transmit two pixel data per pixel clock to interface.
This feature now is required to be enabled to easy migrant to higher
resolution applications in future. However since some legacy chipsets
does not support this feature, this feature is enabled by setting
wide_bus_en flag to true within msm_dp_desc struct.
changes in v2:
-- remove compression related code from timing
-- remove op_info from struct msm_drm_private
-- remove unnecessary wide_bus_en variables
-- pass wide_bus_en into timing configuration by struct msm_dp
Changes in v3:
-- split patch into 3 patches
-- enable widebus feature base on chip hardware revision
Changes in v5:
-- DP_INTF_CONFIG_DATABUS_WIDEN
Changes in v6:
-- static inline bool msm_dp_wide_bus_enable() in msm_drv.h
Changes in v7:
-- add Tested-by
Changes in v9:
-- add wide_bus_en to msm_dp_desc
Changes in v10:
-- add wide_bus_en boolean to dp_catalog struc to avoid passing it as parameter
Changes in v11:
-- add const to dp_catalog_hw_revision()
-- add const to msm_dp_wide_bus_available()
Changes in v12:
-- dp_catalog_hw_revision(const struct dp_catalog *dp_catalog)
-- msm_dp_wide_bus_available(const struct msm_dp *dp_display)
Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Reported-by: kernel test robot <lkp@intel.com>
Tested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/476283/
Link: https://lore.kernel.org/r/1645824192-29670-5-git-send-email-quic_khsieh@quicinc.com
[DB: fixed the compilation]
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Currently DP driver will allocate panel bridge for eDP panels. This
supports only the following topology:
- eDP encoder ⇒ eDP panel (wrapped using panel-bridge)
Simplify this code to just check if there is any next bridge in the
chain (be it a panel bridge or regular bridge). Rename panel_bridge
field to next_bridge accordingly.
This allows one to use e.g. one of the following display topologies:
- eDP encoder ⇒ ptn3460 ⇒ fixed LVDS panel
- eDP encoder ⇒ ptn3460 ⇒ LVDS connector with EDID lines for panel autodetect
- eDP encoder ⇒ ptn3460 ⇒ THC63LVD1024 ⇒ DPI panel.
- eDP encoder ⇒ LT8912 ⇒ DSI panel
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20220211224006.1797846-3-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
DP driver is a generic driver which supports both eDP and DP.
For debugging purpose it is required to have capabilities to
differentiate message are generated from eDP or DP. This patch
add connector type into debug messages for this purpose.
Changes in v3:
-- replace original patch into 3 patches
Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/1643828199-8564-2-git-send-email-quic_khsieh@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
DP CTS test case 4.2.2.6 has valid edid with bad checksum on purpose
and expect DP source return correct checksum. During drm edid read,
correct edid checksum is calculated and stored at
connector::real_edid_checksum.
The problem is struct dp_panel::connector never be assigned, instead the
connector is stored in struct msm_dp::connector. When we run compliance
testing test case 4.2.2.6 dp_panel_handle_sink_request() won't have a valid
edid set in struct dp_panel::edid so we'll try to use the connectors
real_edid_checksum and hit a NULL pointer dereference error because the
connector pointer is never assigned.
Changes in V2:
-- populate panel connector at msm_dp_modeset_init() instead of at dp_panel_read_sink_caps()
Changes in V3:
-- remove unhelpful kernel crash trace commit text
-- remove renaming dp_display parameter to dp
Changes in V4:
-- add more details to commit text
Changes in v10:
-- group into one series
Changes in v11:
-- drop drm/msm/dp: dp_link_parse_sink_count() return immediately if aux read
Fixes: 7948fe12d4 ("drm/msm/dp: return correct edid checksum after corrupted edid checksum read")
Signee-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/1642531648-8448-3-git-send-email-quic_khsieh@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Current DP drivers have regulators, clocks, irq and phy are grouped
together within a function and executed not in a symmetric manner.
This increase difficulty of code maintenance and limited code scalability.
This patch divides the driver life cycle of operation into four states,
resume (including booting up), dongle plugin, dongle unplugged and suspend.
Regulators, core clocks and irq are grouped together and enabled at resume
(or booting up) so that the DP controller is armed and ready to receive HPD
plugin interrupts. HPD plugin interrupt is generated when a dongle plugs
into DUT (device under test). Once HPD plugin interrupt is received, DP
controller will initialize phy so that dpcd read/write will function and
following link training can be proceeded successfully. DP phy will be
disabled after main link is teared down at end of unplugged HPD interrupt
handle triggered by dongle unplugged out of DUT. Finally regulators, code
clocks and irq are disabled at corresponding suspension.
Changes in V2:
-- removed unnecessary dp_ctrl NULL check
-- removed unnecessary phy init_count and power_count DRM_DEBUG_DP logs
-- remove flip parameter out of dp_ctrl_irq_enable()
-- add fixes tag
Changes in V3:
-- call dp_display_host_phy_init() instead of dp_ctrl_phy_init() at
dp_display_host_init() for eDP
Changes in V4:
-- rewording commit text to match this commit changes
Changes in V5:
-- rebase on top of msm-next branch
Changes in V6:
-- delete flip variable
Changes in V7:
-- dp_ctrl_irq_enable/disabe() merged into dp_ctrl_reset_irq_ctrl()
Changes in V8:
-- add more detail comment regrading dp phy at dp_display_host_init()
Changes in V9:
-- remove set phy_initialized to false when -ECONNRESET detected
Changes in v10:
-- group into one series
Changes in v11:
-- drop drm/msm/dp: dp_link_parse_sink_count() return immediately
if aux read
Changes in v12:
-- move dp_display_host_phy_exit() after dp_display_host_deinit()
Changes in v13:
-- do not execute phy_init until plugged_in interrupt for edp, same as DP.
Changes in v14:
-- remove redundant dp->core_initialized = false form dp_pm_suspend.
Changes in v15:
-- remove core_initialized flag check at both host_init and host_deinit
Changes in v16:
-- remove dp_display_host_phy_exit core_initialized=false at dp_pm_suspend
Changes in v17:
-- remove core_initialized checking before execute attention_cb()
Changes in v18:
-- remove core_initialized checking at dp_pm_suspend
Fixes: 8ede2ecc3e ("drm/msm/dp: Add DP compliance tests on Snapdragon Chipsets")
Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/1642531648-8448-2-git-send-email-quic_khsieh@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
The Qualcomm SM8350 platform comes with a single DisplayPort controller,
add support for this in the DisplayPort driver.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20211228045934.1524865-1-bjorn.andersson@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
The sc8180x has 2 DP and 1 eDP controllers, add support for these to the
DP driver.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20211217002643.2305526-1-bjorn.andersson@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Remove unneeded variable used to store return value.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Changcheng Deng <deng.changcheng@zte.com.cn>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20211215085554.444351-1-deng.changcheng@zte.com.cn
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Add checking aux read/write status at both dp_link_parse_sink_count()
and dp_link_parse_sink_status_filed() to avoid long timeout delay if
dp aux read/write failed at timeout due to cable unplugged.
Changes in V4:
-- split this patch as stand alone patch
Changes in v5:
-- rebase on msm-next branch
Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Tested-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/1638985262-2072-1-git-send-email-quic_khsieh@quicinc.com
Signed-off-by: Rob Clark <robdclark@chromium.org>
Currently the msm_dp_*** functions implement the same sequence which would
happen when drm_bridge is used. hence get rid of this intermediate layer
and align with the drm_bridge usage to avoid customized implementation.
Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Changes in v2:
-- revise commit text
-- rename dp_bridge to msm_dp_bridge
-- delete empty functions
Changes in v3:
-- replace kzalloc() with devm_kzalloc()
-- replace __dp_display_enable() with dp_display_enable()
-- replace __dp_display_disable() with dp_display_disable()
Changes in v4:
-- msm_dp_bridge_init() called from msm_dp_modeset_init() same as dsi
Changes in v5:
-- delete attach, mode_fixup and pre_enable from dp_bridge_ops
Changes in v6:
-- rebase on msm-next-plus-fixes branch
Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Link: https://lore.kernel.org/r/1638918933-2544-1-git-send-email-quic_khsieh@quicinc.com
Signed-off-by: Rob Clark <robdclark@chromium.org>
In preparation for registering the mdss interrupt controller earlier,
move the allocation of msm_drm_private from component bind time to
msm_drv probe; this also allows us to use the devm variant of kzalloc.
Since it is not right to allocate the drm_device at probe time (as
it should exist only when all components are bound, and taken down
when components get cleaned up), the only way to make this happen is
to pass a pointer to msm_drm_private as driver data (like done in
many other DRM drivers), instead of one to drm_device like it's
currently done in this driver.
This is also simplifying some bind/unbind functions around drm/msm,
as some of them are using drm_device just to grab a pointer to the
msm_drm_private structure, which we now retrieve in one call.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20211201105210.24970-2-angelogioacchino.delregno@collabora.com
Signed-off-by: Rob Clark <robdclark@chromium.org>
Since '8ede2ecc3e5e ("drm/msm/dp: Add DP compliance tests on Snapdragon
Chipsets")' the hpd_high member of struct dp_usbpd has been write-only.
Let's clean up the code a little bit by removing the writes as well.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20211106172246.2597431-1-bjorn.andersson@linaro.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
The eDP controller on SC7280 is similar to the eDP/DP controllers
supported by the current driver implementation.
SC7280 supports one EDP and one DP controller which can operate
concurrently.
This change adds the support for eDP and DP controller on sc7280.
Signed-off-by: Sankeerth Billakanti <quic_sbillaka@quicinc.com>
changes in v3:
- Split into patches according to function (Dmitry Baryshkov)
- Use DP_CONTROLLER_1 for eDP controller intf (Dmitry Baryshkov)
- Use DP_CONTROLLER_0 for sc7280-dp (Dmitry Baryshkov)
- Add macro in drm_helper.h for checking ssc capability (Stephen Boyd)
- Use existing macro to check assr capability (Stephen Boyd)
- Add comment for HPD_INIT_SETUP delay (Stephen Boyd)
changes in v2:
- Don't initialize variables to 0 (Stephen Boyd)
- Use const for read-only dpcd (Stephen Boyd)
- Remove zero pixel clock check (Stephen Boyd)
- Sort compatible strings alphabetically (Stephen Boyd)
- Use pwm_bl.c for backlight instead of gpio (Stephen Boyd)
- Change return type for functions returning always 0 (Matthias Kaehlcke)
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/1635839325-401-3-git-send-email-quic_sbillaka@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Based on the removal of the g_dp_display and the movement of the
priv->dp lookup into the DP code it's now possible to have multiple
DP instances.
In line with the other controllers in the MSM driver, introduce a
per-compatible list of base addresses which is used to resolve the
"instance id" for the given DP controller. This instance id is used as
index in the priv->dp[] array.
Then extend the initialization code to initialize struct drm_encoder for
each of the registered priv->dp[] and update the logic for associating
each struct msm_dp with the struct dpu_encoder_virt.
A new enum is introduced to document the connection between the
instances referenced in the dpu_intf_cfg array and the controllers in
the DP driver and sc7180 is updated.
Lastly, bump the number of struct msm_dp instances carries by priv->dp
to 3, the currently known maximum number of controllers found in a
Qualcomm SoC.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20211016221843.2167329-6-bjorn.andersson@linaro.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
eDP panels might need some power sequencing and backlight management,
so make it possible to associate a drm_panel with an eDP instance and
prepare and enable the panel accordingly.
Now that we know which hardware instance is DP and which is eDP,
parser->parse() is passed the connector_type and the parser is limited
to only search for a panel in the eDP case.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20211016221843.2167329-5-bjorn.andersson@linaro.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
As the following patches introduced support for multiple DP blocks in a
platform and some of those block might be eDP it becomes useful to be
able to specify the connector type per block.
Although there's only a single block at this point, the array of descs
and the search in dp_display_get_desc() are introduced here to simplify
the next patch, that does introduce support for multiple DP blocks.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20211016221843.2167329-4-bjorn.andersson@linaro.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
As the Qualcomm DisplayPort driver only supports a single instance of
the driver the commonly used struct dp_display is kept in a global
variable. As we introduce additional instances this obviously doesn't
work.
Replace this with a combination of existing references to adjacent
objects and drvdata.
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211016221843.2167329-2-bjorn.andersson@linaro.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
The debugfs code is provided an array of a single drm_connector. Then to
access the connector, the list of all connectors of the DRM device is
traversed and all non-DisplayPort connectors are skipped, to find the
one and only DisplayPort connector.
But as we move to support multiple DisplayPort controllers this will now
find multiple connectors and has no way to distinguish them.
Pass the single connector to dp_debug_get() and use this in the debugfs
functions instead, both to simplify the code and the support the
multiple instances.
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211015232213.1839472-1-bjorn.andersson@linaro.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
Currently there is audio not working problem after system resume from suspend
if hdmi monitor stay plugged in at DUT. However this problem does not happen
at normal operation but at a particular test case. The root cause is DP driver
signal audio with connected state at resume which trigger audio trying to setup
audio data path through DP main link but failed due to display port is not setup
and enabled by upper layer framework yet. This patch only have DP driver signal
audio only when DP is in disconnected state so that audio option shows correct
state after system resume. DP driver will not signal audio with connected state
until display enabled executed by upper layer framework where display port is
setup completed and main link is running.
Changes in V2:
-- add details commit text
Fixes: afc9b8b6ba ("drm/msm/dp: signal audio plugged change at dp_pm_resume")
Signed-off-by: Kuogee Hsieh <khsieh@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/1632932224-25102-1-git-send-email-khsieh@codeaurora.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
