-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmLLR2MeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG+hMH/jKGMOAbicR/CRq8
WLKmpb1eTJP2dbeiEs5amBk9DZQhqjx6tIQRCpZoGxBL+XWq7DX2fRLkAT56yS5/
NwferpR6IR9GlhjbfczF0JuQkP6eRUXnLrIKS5MViLI5QrCI80kkj4/mdqUXSiBV
cMfXl5T1j+pb3zHUVXjnmvY+77q6rZTPoGxa/l8d6MaIhAg+jhu2E1HaSaSCX/YK
TViq7ciI9cXoFV9yqhLkkBdGjBV8VQsKmeWEcA738bdSy1WAJSV1SVTJqLFvwdPI
PM1asxkPoQ7jRrwsY4G8pZ3zPskJMS4Qwdn64HK+no2AKhJt2p6MePD1XblcrGHK
QNStMY0=
=LfuD
-----END PGP SIGNATURE-----
Backmerge tag 'v5.19-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux into drm-next
Backmerge in rc6 so I can merge msm next easier.
Linux 5.19-rc6
Signed-off-by: Dave Airlie <airlied@redhat.com>
drm_crtc.h has no need for linux/media-bus-format.h, so don't
include it. Avoids useless rebuilds of the entire universe when
touching linux/media-bus-format.h.
Quite a few placs do currently depend on linux/media-bus-format.h
without actually including it directly. All of those need to be
fixed up.
v2: Deal with ingenic as well
v3: Fix up mxsfb and remaining parts of imx
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220630195114.17407-4-ville.syrjala@linux.intel.com
drm_crtc.h has no need for linux/fb.h, so don't include it.
Avoids useless rebuilds of the entire universe when
touching linux/fb.h.
Quite a few placs do currently depend on linux/fb.h or other
headers pulled in by it without actually including any of it
directly. All of those need to be fixed up.
v2: Split the vmwgfx change out
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220630195114.17407-3-ville.syrjala@linux.intel.com
sparse reports
drivers/gpu/drm/vc4/vc4_drv.c:270:27: warning: symbol 'vc4_dma_range_matches' was not declared. Should it be static?
vc4_dma_range_matches is only used in vc4_drv.c, so it's storage class specifier
should be static.
Fixes: da8e393e23 ("drm/vc4: drv: Adopt the dma configuration from the HVS or V3D component")
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220629200101.498138-1-trix@redhat.com
With the change to 2 pixels/clock, the pixel doubling in the PV
results in doubling each pair of pixels, ie ABABCDCD instead of
AABBCCDD.
Move the pixel doubling to the HDMI block, however this means
that DBLCLK modes now fall foul of requiring even values for
all the horizontal timing parameters.
As both 480i and 576i fail this, attempt to fix up DBLCLK modes
that have odd timings values.
Fixes: 8323989140 ("drm/vc4: hdmi: Support the BCM2711 HDMI controllers")
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20220613144800.326124-34-maxime@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
For interlaced modes the timings were not being correctly
programmed into the HDMI block, so correct them.
Fixes: 8323989140 ("drm/vc4: hdmi: Support the BCM2711 HDMI controllers")
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20220613144800.326124-33-maxime@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Whenever the maximum BPC is changed, vc4_hdmi_encoder_compute_config()
might pick up a different BPC or format depending on the display
capabilities.
That change will have a number of side effects, including the clock
rates and whether the scrambling is enabled.
However, only drm_crtc_state.connectors_changed will be set to true,
since that properly only affects the connector.
This means that while drm_atomic_crtc_needs_modeset() will return true,
and thus drm_atomic_helper_commit_modeset_enables() will call our
encoder atomic_enable() hook, mode_changed will be false.
So crtc_set_mode() will not call our encoder .atomic_mode_set() hook. We
use this hook in vc4 to set the vc4_hdmi_connector_state.output_bpc (and
output_format), and will then reuse the value in .atomic_enable() to select
whether or not scrambling should be enabled.
However, since our clock rate is pre-computed during .atomic_check(), we
end up with the clocks properly configured, but the scrambling disabled,
leading to a blank screen.
Let's set mode_changed to true in our HDMI driver to force the update of
output_bpc, and thus prevent the issue entirely.
Fixes: ba8c0faebb ("drm/vc4: hdmi: Enable 10/12 bpc output")
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Link: https://lore.kernel.org/r/20220613144800.326124-32-maxime@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Increase the number of post-sync blanking lines on odd fields instead of
decreasing it on even fields. This makes the total number of lines
properly match the modelines.
Additionally fix the value of PV_VCONTROL_ODD_DELAY, which did not take
pixels_per_clock into account, causing some displays to invert the
fields when driven by bcm2711.
Fixes: 682e62c454 ("drm/vc4: Fix support for interlaced modes on HDMI.")
Signed-off-by: Mateusz Kwiatkowski <kfyatek+publicgit@gmail.com>
Link: https://lore.kernel.org/r/20220613144800.326124-31-maxime@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The MISC_CONTROL register allows configuration of pixel repetition
for pixel doubling in the HDMI block instead of PixelValve.
It was already defined for vc5, so add it for vc4.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20220613144800.326124-29-maxime@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The block can detect what the incoming image timings are for
debug purposes. Add them to the list of registers understood
by the driver to allow easy dumping of the values.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20220613144800.326124-28-maxime@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
This bit ensures data island packets are never generated when disallowed
by HDCP. As no Pi boards support HDCP this is providing an unnecessary
restriction
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Link: https://lore.kernel.org/r/20220613144800.326124-27-maxime@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
This path actually occurs when audio is started during a hdmi mode set.
As the data will be written by vc4_hdmi_set_infoframes when packet RAM
is enabled again, don't treat as an error
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Link: https://lore.kernel.org/r/20220613144800.326124-26-maxime@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The current HDMI driver, in vc4_hdmi_audio_can_stream() checks whether
the display output is enabled.
This has been there in one form or the other since the introduction of
the audio support in the VC4 HDMI driver in commit bb7d785688
("drm/vc4: Add HDMI audio support"), but no justification for this check
is in the commit message, or in the discussions around the patches.
One can only assume this was done to prevent a user from playing audio
on the ALSA soundcard when the monitor doesn't support it.
However, this is causing some issues. Indeed, Kodi, for example, was
hitting some errors if it was streaming audio during a modeset. With the
theory above, it does make sense, but the display and audio threads are
typically completely different processes with no opportunity to
synchronise which makes it hard to workaround.
Removing that check also doesn't seem to cause any trouble, so let's
just remove it.
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Link: https://lore.kernel.org/r/20220613144800.326124-25-maxime@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The BCM2835-37 found in the RaspberryPi 0 to 3 have a power domain
attached to the HDMI block, handled in Linux through runtime_pm.
That power domain is shared with the VEC block, so even if we put our
runtime_pm reference in the HDMI driver it would keep being on. If the
VEC is disabled though, the power domain would be disabled and we would
lose any initialization done in our bind implementation.
That initialization involves calling the reset function and initializing
the CEC registers.
Let's move the initialization to our runtime_resume implementation so
that we initialize everything properly if we ever need to.
Fixes: c86b412143 ("drm/vc4: hdmi: Move the HSM clock enable to runtime_pm")
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20220613144800.326124-24-maxime@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
If the controller isn't clocked or its domain powered up, the register
accesses will either stall the CPU or return garbage, respectively.
Thus, we had a warning in our register access function to complain when
that kind of risky accesses were performed.
In order to check the runtime_pm power state, we were using
pm_runtime_active(), but it turns out that it will become active only
once the runtime_resume hook has been executed.
This prevents us from doing any WARN-free register access in our
runtime_resume() implementation, while this is valid.
Let's switch to pm_runtime_status_suspended() instead.
Fixes: 14e193b956 ("drm/vc4: hdmi: Warn if we access the controller while disabled")
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20220613144800.326124-23-maxime@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The HDMI block can repeat pixels for double clocked modes,
and the firmware is now configuring the block to do this as
the PV is doing it incorrectly when at 2pixels/clock.
If the kernel doesn't reset it then we end up with strange
modes.
Reset MISC_CONTROL.
Fixes: 8323989140 ("drm/vc4: hdmi: Support the BCM2711 HDMI controllers")
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20220613144800.326124-22-maxime@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
We are getting occasional VC4_HD_MAI_CTL_ERRORF in
HDMI_MAI_CTL which seem to correspond with audio dropouts.
Reduce the threshold where we deassert DREQ to avoid the fifo
overfilling
Fixes: bb7d785688 ("drm/vc4: Add HDMI audio support")
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Link: https://lore.kernel.org/r/20220613144800.326124-21-maxime@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Using a hdmi analyser the bytes in packet ram
registers beyond the length were visible in the
infoframes and it flagged the checksum as invalid.
Zeroing unused words of packet RAM avoids this
Fixes: 21317b3fba ("drm/vc4: Set up the AVI and SPD infoframes.")
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Link: https://lore.kernel.org/r/20220613144800.326124-20-maxime@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The vc5 HDMI registers hadn't been added into the debugfs
register sets, therefore weren't dumped on request.
Add them in.
Fixes: 8323989140 ("drm/vc4: hdmi: Support the BCM2711 HDMI controllers")
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20220613144800.326124-19-maxime@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The dmas property is used to hold the dmaengine channel used for audio
output.
Older device trees were missing that property, so if it's not there we
disable the audio output entirely.
However, some overlays have set an empty value to that property, mostly
to workaround the fact that overlays cannot remove a property. Let's add
a test for that case and if it's empty, let's disable it as well.
Cc: <stable@vger.kernel.org>
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Link: https://lore.kernel.org/r/20220613144800.326124-18-maxime@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
vc4_dsi_encoder_disable is partially an open coded version of
drm_bridge_chain_disable, but it missed a termination condition
in the loop for ->disable which meant that no post_disable
calls were made.
Add in the termination clause.
Fixes: 033bfe7538 ("drm/vc4: dsi: Fix bridge chain handling")
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20220613144800.326124-17-maxime@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
DSI0 seemingly had very little or no testing as a load of
the register mappings were incorrect/missing, so host
transfers always timed out due to enabling/checking incorrect
bits in the interrupt enable and status registers.
Fixes: 4078f57571 ("drm/vc4: Add DSI driver")
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20220613144800.326124-16-maxime@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
vc4_dsi was registering both dsi0 and dsi1 as VC4_ENCODER_TYPE_DSI1
which seemed to work OK for a single DSI display, but fails
if there are two DSI displays connected.
Update to register the correct type.
Fixes: 4078f57571 ("drm/vc4: Add DSI driver")
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20220613144800.326124-15-maxime@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
For slightly unknown reasons, dsi0 takes a different pixel format
to dsi1, and that has to be set in the pixel valve.
Amend the setup accordingly.
Fixes: a86773d120 ("drm/vc4: Add support for feeding DSI encoders from the pixel valve.")
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20220613144800.326124-14-maxime@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The divider calculations tried to find the divider just faster than the
clock requested. However if it required a divider of 7 then the for loop
aborted without handling the "error" case, and could end up with a clock
lower than requested.
The integer divider from parent PLL to DSI clock is also capable of
going up to /255, not just /7 that the driver was trying. This allows
for slower link frequencies on the DSI bus where the resolution permits.
Correct the loop so that we always have a clock greater than requested,
and covering the whole range of dividers.
Fixes: 86c1b9eff3 ("drm/vc4: Adjust modes in DSI to work around the integer PLL divider.")
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20220613144800.326124-13-maxime@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
On Pi0-3 the driver allocates a buffer and requests a DMA channel
because the ARM can't write to DSI1's registers directly.
However, we never release that buffer or channel. Let's add a
device-managed action to release each.
Fixes: 4078f57571 ("drm/vc4: Add DSI driver")
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20220613144800.326124-12-maxime@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
In a couple of error/incomplete configuration cases, the
DPI_FORMAT bits wouldn't get set.
Enforce our RGB888 default in all these cases.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20220613144800.326124-11-maxime@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
DRM provides flags for inverting pixel clock and output enable
signals, but these were not mapped to the relevant registers.
Add those mappings.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20220613144800.326124-10-maxime@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The hardware can combine H&V syncs onto the output enable line
as composite syncs, so add the relevant configuration to do that.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20220613144800.326124-9-maxime@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Move from only supporting the default of pre-multiplied
alpha to supporting user specified blend mode using the
standardised property.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20220613144800.326124-7-maxime@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The current plane margin calculation code clips the right and bottom
edges of the range based using the left and top margins.
This is obviously wrong, so let's fix it.
Fixes: 666e73587f ("drm/vc4: Take margin setup into account when updating planes")
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20220613144800.326124-6-maxime@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
There is little harm in ignoring fractional coordinates
(they just get truncated).
Without this:
modetest -M vc4 -F tiles,gradient -s 32:1920x1080-60 -P89@74:1920x1080*.1.1@XR24
is rejected. We have the same issue in Kodi when trying to
use zoom options on video.
Note: even if all coordinates are fully integer. e.g.
src:[0,0,1920,1080] dest:[-10,-10,1940,1100]
it will still get rejected as drm_atomic_helper_check_plane_state
uses drm_rect_clip_scaled which transforms this to fractional src coords
Fixes: 21af94cf1a ("drm/vc4: Add support for scaling of display planes.")
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Link: https://lore.kernel.org/r/20220613144800.326124-5-maxime@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The core clock computation takes into account both the load due to the
input (ie, planes) and its output (ie, encoders).
However, while the input load needs to consider all the planes, and thus
sum all of their associated loads, the output happens mostly in
parallel.
Therefore, we need to consider only the maximum of all the output loads,
and not the sum like we were doing. This resulted in a clock rate way
too high which could be discarded for being too high by the clock
framework.
Since recent changes, the clock framework will even downright reject it,
leading to a core clock being too low for its current needs.
Fixes: 16e101051f ("drm/vc4: Increase the core clock based on HVS load")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20220613144800.326124-4-maxime@cerno.tech
We currently ignore the clk_set_min_rate return code assuming it would
succeed. However, it can fail if we ask for a rate higher than the
current maximum for example.
Since we can't fail in atomic_commit, at least warn on failure.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20220613144800.326124-3-maxime@cerno.tech
vc4_drv isn't necessarily under the /soc node in DT as it is a
virtual device, but it is the one that does the allocations.
The DMA addresses are consumed by primarily the HVS or V3D, and
those require VideoCore cache alias address mapping, and so will be
under /soc.
During probe find the a suitable device node for HVS or V3D,
and adopt the DMA configuration of that node.
Cc: <stable@vger.kernel.org>
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20220613144800.326124-2-maxime@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Commit 30f8c74ca9 ("drm/vc4: Warn if some v3d code is run on BCM2711")
introduced a check in vc4_perfmon_get() that dereferences a pointer before
we checked whether that pointer is valid or not.
Let's rework that function a bit to do things in the proper order.
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: 30f8c74ca9 ("drm/vc4: Warn if some v3d code is run on BCM2711")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: José Expósito <jose.exposito89@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220622080243.22119-1-maxime@cerno.tech
The vc4_check_tex_size() function is supposed to return false on error
but this error path accidentally returns -ENODEV (which means true).
Fixes: 30f8c74ca9 ("drm/vc4: Warn if some v3d code is run on BCM2711")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/YrMKK89/viQiaiAg@kili
there is an unexpected word "the" in the comments that need to be dropped
file: drivers/gpu/drm/vc4/vc4_regs.h
line: 267
/* Set when the the downstream tries to read from the display FIFO
changed to
/* Set when the downstream tries to read from the display FIFO
Signed-off-by: Jiang Jian <jiangjian@cdjrlc.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220621130550.126915-1-jiangjian@cdjrlc.com
drm_crtc.h has no need for drm_blend.h, so don't include it.
Avoids useless rebuilds of the entire universe when
touching drm_blend.h.
Quite a few placs do currently depend on drm_blend.h without
actually including it directly. All of those need to be fixed
up.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220613200317.11305-4-ville.syrjala@linux.intel.com
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Jani Nikula <jani.nikula@intel.com>
drm_crtc.h has no need for drm_frambuffer.h, so don't include it.
Avoids useless rebuilds of the entire universe when
touching drm_framebuffer.h.
Quite a few placs do currently depend on drm_framebuffer.h without
actually including it directly. All of those need to be fixed
up.
v2: Fix up msm some more
v2: Deal with ingenic and shmobile as well
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220614095449.29311-1-ville.syrjala@linux.intel.com
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Jani Nikula <jani.nikula@intel.com>
The BCM2711 has a separate driver for the v3d, and thus we can't call
into any of the driver entrypoints that rely on the v3d being there.
Let's add a bunch of checks and complain loudly if that ever happen.
Reviewed-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20220610115149.964394-15-maxime@cerno.tech
When doing an asynchronous page flip (PAGE_FLIP ioctl with the
DRM_MODE_PAGE_FLIP_ASYNC flag set), the current code waits for the
possible GPU buffer being rendered through a call to
vc4_queue_seqno_cb().
On the BCM2835-37, the GPU driver is part of the vc4 driver and that
function is defined in vc4_gem.c to wait for the buffer to be rendered,
and once it's done, call a callback.
However, on the BCM2711 used on the RaspberryPi4, the GPU driver is
separate (v3d) and that function won't do anything. This was working
because we were going into a path, due to uninitialized variables, that
was always scheduling the callback.
However, we were never actually waiting for the buffer to be rendered
which was resulting in frames being displayed out of order.
The generic API to signal those kind of completion in the kernel are the
DMA fences, and fortunately the v3d drivers supports them and signal
when its job is done. That API also provides an equivalent function that
allows to have a callback being executed when the fence is signalled as
done.
Let's change our driver a bit to rely on the previous function for the
older SoCs, and on DMA fences for the BCM2711.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Melissa Wen <mwen@igalia.com>
Link: https://lore.kernel.org/r/20220610115149.964394-14-maxime@cerno.tech
The BCM2711 doesn't have a v3d GPU so we don't want to call into its BO
management code. Let's create an asynchronous page-flip handler for the
BCM2711 that just calls into the common code.
Reviewed-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20220610115149.964394-13-maxime@cerno.tech
The function vc4_async_page_flip() handles asynchronous page-flips in
the vc4 driver.
However, it mixes some generic code with code that should only be run on
older generations that have the GPU handled by the vc4 driver.
Let's split the generic part out of vc4_async_page_flip() and into a
common function that we be reusable by an handler made for the BCM2711.
Reviewed-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20220610115149.964394-12-maxime@cerno.tech
We'll soon introduce another completion callback source that won't need
to use the BO reference counting, so let's move it around to create a
function we will be able to share between both callbacks.
Reviewed-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20220610115149.964394-11-maxime@cerno.tech
We'll need to extend the vc4_async_flip_state structure to rely on
another callback implementation, so let's move the current one into a
union.
Reviewed-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20220610115149.964394-10-maxime@cerno.tech
On the BCM2711, we currently call the vc4_bo_cache_init() and
vc4_gem_init() functions. These functions initialize the BO and GEM
backends.
However, this code was initially created to accomodate the requirements
of the GPU on the older SoCs, while the BCM2711 has a separate driver
for it. So let's just skip these calls when we're on a newer hardware.
Reviewed-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20220610115149.964394-9-maxime@cerno.tech
