As noted in commit 28c2d1a7a0 ("net: bcmgenet: enable loopback
during UniMAC sw_reset") the UniMAC must be clocked while sw_reset
is asserted for its state machines to reset cleanly.
The transmit and receive clocks used by the UniMAC are derived from
the signals used on its PHY interface. The bcmgenet MAC can be
configured to work with different PHY interfaces including MII,
GMII, RGMII, and Reverse MII on internal and external interfaces.
Unfortunately for the UniMAC, when configured for MII the Tx clock
is always driven from the PHY which places it outside of the direct
control of the MAC.
The earlier commit enabled a local loopback mode within the UniMAC
so that the receive clock would be derived from the transmit clock
which addressed the observed issue with an external GPHY disabling
it's Rx clock. However, when a Tx clock is not available this
loopback is insufficient.
This commit implements a workaround that leverages the fact that
the MAC can reliably generate all of its necessary clocking by
enterring the external GPHY RGMII interface mode with the UniMAC in
local loopback during the sw_reset interval. Unfortunately, this
has the undesirable side efect of the RGMII GTXCLK signal being
driven during the same window.
In most configurations this is a benign side effect as the signal
is either not routed to a pin or is already expected to drive the
pin. The one exception is when an external MII PHY is expected to
drive the same pin with its TX_CLK output creating output driver
contention.
This commit exploits the IEEE 802.3 clause 22 standard defined
isolate mode to force an external MII PHY to present a high
impedance on its TX_CLK output during the window to prevent any
contention at the pin.
The MII interface is used internally with the 40nm internal EPHY
which agressively disables its clocks for power savings leading to
incomplete resets of the UniMAC and many instabilities observed
over the years. The workaround of this commit is expected to put
an end to those problems.
Fixes: 1c1008c793 ("net: bcmgenet: add main driver file")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before this change of_get_phy_mode() returned an enum,
phy_interface_t. On error, -ENODEV etc, is returned. If the result of
the function is stored in a variable of type phy_interface_t, and the
compiler has decided to represent this as an unsigned int, comparision
with -ENODEV etc, is a signed vs unsigned comparision.
Fix this problem by changing the API. Make the function return an
error, or 0 on success, and pass a pointer, of type phy_interface_t,
where the phy mode should be stored.
v2:
Return with *interface set to PHY_INTERFACE_MODE_NA on error.
Add error checks to all users of of_get_phy_mode()
Fixup a few reverse christmas tree errors
Fixup a few slightly malformed reverse christmas trees
v3:
Fix 0-day reported errors.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The EPHY integrated into the 40nm Set-Top Box devices can falsely
detect energy when connected to a disabled peer interface. When the
peer interface is enabled the EPHY will detect and report the link
as active, but on occasion may get into a state where it is not
able to exchange data with the connected GENET MAC. This issue has
not been observed when the link parameters are auto-negotiated;
however, it has been observed with a manually configured link.
It has been empirically determined that issuing a soft reset to the
EPHY when energy is detected prevents it from getting into this bad
state.
Fixes: 1c1008c793 ("net: bcmgenet: add main driver file")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It turns out that the "Workaround for putting the PHY in IDDQ mode"
used by the internal EPHYs on 40nm Set-Top Box chips when powering
down puts the interface to the GENET MAC in a state that can cause
subsequent MAC resets to be incomplete.
Rather than restore the forced soft reset when powering up internal
PHYs, this commit moves the invocation of phy_init_hw earlier in
the MAC initialization sequence to just before the MAC reset in the
open and resume functions. This allows the interface to be stable
and allows the MAC resets to be successful.
The bcmgenet_mii_probe() function is split in two to accommodate
this. The new function bcmgenet_mii_connect() handles the first
half of the functionality before the MAC initialization, and the
bcmgenet_mii_config() function is extended to provide the remaining
PHY configuration following the MAC initialization.
Fixes: 484bfa1507 ("Revert "net: bcmgenet: Software reset EPHY after power on"")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When commit 28b2e0d2cd ("net: phy: remove parameter new_link from
phy_mac_interrupt()") removed the new_link parameter it set the
phydev->link state from the MAC before invoking phy_mac_interrupt().
However, once commit 88d6272aca ("net: phy: avoid unneeded MDIO
reads in genphy_read_status") was added this initialization prevents
the proper determination of the connection parameters by the function
genphy_read_status().
This commit removes that initialization to restore the proper
functionality.
Fixes: 88d6272aca ("net: phy: avoid unneeded MDIO reads in genphy_read_status")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RGMII_MODE_EN bit value was 0 for GENET versions 1 through 3, and
became 6 for GENET v4 and above, account for that difference.
Fixes: aa09677cba ("net: bcmgenet: add MDIO routines")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure that we completely quiesce the network device, including its
DMA to avoid having it continue to receive packets while there is no
software alive to service those.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of having a hard failure and stopping the driver's probe
routine, generate a random Ethernet MAC address to keep going.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
phydev->dev_flags is entirely dependent on the PHY device driver which
is going to be used, setting the internal GENET PHY revision in those
bits only makes sense when drivers/net/phy/bcm7xxx.c is the PHY driver
being used.
Fixes: 487320c541 ("net: bcmgenet: communicate integrated PHY revision to PHY driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change enables the use of SW timestamping on the Raspberry Pi 4.
bcmgenet's transmit function bcmgenet_xmit() implements software
timestamping. However the SOF_TIMESTAMPING_TX_SOFTWARE capability was
missing and only SOF_TIMESTAMPING_RX_SOFTWARE was announced. By using
ethtool_ops bcmgenet_ethtool_ops() as get_ts_info(), the
SOF_TIMESTAMPING_TX_SOFTWARE capability is announced.
Similar to commit a8f5cb9e79 ("smsc95xx: use ethtool_op_get_ts_info()")
Signed-off-by: Ryan M. Collins <rmc032@bucknell.edu>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dev_kfree_skb() function performs also input parameter validation.
Thus the test around the shown calls is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While using net_dim, a dim_sample was used without ever initializing the
comps value. Added use of DIV_ROUND_DOWN_ULL() to prevent potential
overflow, it should not be a problem to save the final result in an int
because after the division by epms the value should not be larger than a
few thousand.
[ 1040.127124] UBSAN: Undefined behaviour in lib/dim/dim.c:78:23
[ 1040.130118] signed integer overflow:
[ 1040.131643] 134718714 * 100 cannot be represented in type 'int'
Fixes: 398c2b05bb ("linux/dim: Add completions count to dim_sample")
Signed-off-by: Yamin Friedman <yaminf@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we silently ignore filters if we cannot meet the filter
requirements. This will lead to the MAC dropping packets that are
expected to pass. A better solution would be to set the NIC to promisc
mode when the required filters cannot be met.
Also correct the number of MDF filters supported. It should be 17,
not 16.
Signed-off-by: Justin Chen <justinpopo6@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Tal Gilboa and Yamin Fridman
Implement net DIM over a generic DIM library, add RDMA DIM
dim.h lib exposes an implementation of the DIM algorithm for
dynamically-tuned interrupt moderation for networking interfaces.
We want a similar functionality for other protocols, which might need to
optimize interrupts differently. Main motivation here is DIM for NVMf
storage protocol.
Current DIM implementation prioritizes reducing interrupt overhead over
latency. Also, in order to reduce DIM's own overhead, the algorithm might
take some time to identify it needs to change profiles. While this is
acceptable for networking, it might not work well on other scenarios.
Here we propose a new structure to DIM. The idea is to allow a slightly
modified functionality without the risk of breaking Net DIM behavior for
netdev. We verified there are no degradations in current DIM behavior with
the modified solution.
Suggested solution:
- Common logic is implemented in lib/dim/dim.c
- Net DIM (existing) logic is implemented in lib/dim/net_dim.c, which uses
the common logic in dim.c
- Any new DIM logic will be implemented in "lib/dim/new_dim.c".
This new implementation will expose modified versions of profiles,
dim_step() and dim_decision().
- DIM API is declared in include/linux/dim.h for all implementations.
Pros for this solution are:
- Zero impact on existing net_dim implementation and usage
- Relatively more code reuse (compared to two separate solutions)
- Increased extensibility
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGhZs6bAKwk/OTgTpSD+KveBX+j4FAl0SiDAACgkQSD+KveBX
+j4mlQgAoabbtxwIapMg62tKhnlr/3hEEyuEjiQRhzMUb5y5zOIJNRL82Nerv4K3
oD7v76emw/Xb1ErPe4yJJRdkpbpabEAFKbqkM0R7xFPNK33ZbphlU1d9YGgUKp1W
Uieydn5kfubzi6p7R1TC7c2qW1Wr6rE1wnNJyC/sy8zFEP/OEH0NmgPDyOs7ckWI
xaoJ1lhNWMoGN+Qk+fxazd1VtsKdcbc9JvLD2e8ON5qWdnuNiLhawcJVoWzfsCAa
V/Tdff+Rj9bVFsi468u20og4EdV3ceAOTzMnhCYpAtYZHVbVk6MFgh87uQYkTrfY
sW8BDmWKkRdHtzHd3a3yQiVDnz/iuw==
=bAZn
-----END PGP SIGNATURE-----
Merge tag 'blk-dim-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mamameed says:
====================
Generic DIM
From: Tal Gilboa and Yamin Fridman
Implement net DIM over a generic DIM library, add RDMA DIM
dim.h lib exposes an implementation of the DIM algorithm for
dynamically-tuned interrupt moderation for networking interfaces.
We want a similar functionality for other protocols, which might need to
optimize interrupts differently. Main motivation here is DIM for NVMf
storage protocol.
Current DIM implementation prioritizes reducing interrupt overhead over
latency. Also, in order to reduce DIM's own overhead, the algorithm might
take some time to identify it needs to change profiles. While this is
acceptable for networking, it might not work well on other scenarios.
Here we propose a new structure to DIM. The idea is to allow a slightly
modified functionality without the risk of breaking Net DIM behavior for
netdev. We verified there are no degradations in current DIM behavior with
the modified solution.
Suggested solution:
- Common logic is implemented in lib/dim/dim.c
- Net DIM (existing) logic is implemented in lib/dim/net_dim.c, which uses
the common logic in dim.c
- Any new DIM logic will be implemented in "lib/dim/new_dim.c".
This new implementation will expose modified versions of profiles,
dim_step() and dim_decision().
- DIM API is declared in include/linux/dim.h for all implementations.
Pros for this solution are:
- Zero impact on existing net_dim implementation and usage
- Relatively more code reuse (compared to two separate solutions)
- Increased extensibility
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Moved all logic from dim.h and net_dim.h to dim.c and net_dim.c.
This is both more structurally appealing and would allow to only
expose externally used functions.
Signed-off-by: Tal Gilboa <talgi@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Removed 'net' prefix from functions and structs used by external drivers.
Signed-off-by: Tal Gilboa <talgi@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
In order to avoid confusion between the function and the similarly
named struct.
In preparation for removing the 'net' prefix from dim members.
Signed-off-by: Tal Gilboa <talgi@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There was NVMEM support added to of_get_mac_address, so it could now
return ERR_PTR encoded error values, so we need to adjust all current
users of of_get_mac_address to this new fact.
While at it, remove superfluous is_valid_ether_addr as the MAC address
returned from of_get_mac_address is always valid and checked by
is_valid_ether_addr anyway.
Fixes: d01f449c00 ("of_net: add NVMEM support to of_get_mac_address")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two reasons for this.
First, the xmit_more flag conceptually doesn't fit into the skb, as
xmit_more is not a property related to the skb.
Its only a hint to the driver that the stack is about to transmit another
packet immediately.
Second, it was only done this way to not have to pass another argument
to ndo_start_xmit().
We can place xmit_more in the softnet data, next to the device recursion.
The recursion counter is already written to on each transmit. The "more"
indicator is placed right next to it.
Drivers can use the netdev_xmit_more() helper instead of skb->xmit_more
to check the "more packets coming" hint.
skb->xmit_more is retained (but always 0) to not cause build breakage.
This change takes care of the simple s/skb->xmit_more/netdev_xmit_more()/
conversions. Remaining drivers are converted in the next patches.
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
All users of the fixed_phy_add() pass -1 as GPIO number
to the fixed phy driver, and all users of fixed_phy_register()
pass -1 as GPIO number as well, except for the device
tree MDIO bus.
Any new users should create a proper device and pass the
GPIO as a descriptor associated with the device so delete
the GPIO argument from the calls and drop the code looking
requesting a GPIO in fixed_phy_add().
In fixed phy_register(), investigate the "fixed-link"
node and pick the GPIO descriptor from "link-gpios" if
this property exists. Move the corresponding code out
of of_mdio.c as the fixed phy code anyways requires
OF to be in use.
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit c5a54bbcec ("net: bcmgenet: abort suspend on error")
mistakenly introduced register accesses that should not occur
in bcmgenet_wol_power_up_cfg().
Fixes: c5a54bbcec ("net: bcmgenet: abort suspend on error")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If an error occurs during suspension of the driver the driver should
restore the hardware configuration and return an error to force the
system to resume.
Fixes: 0db55093b5 ("net: bcmgenet: return correct value 'ret' from bcmgenet_power_down")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit switches the order of bcmgenet_suspend and bcmgenet_resume
in the file to prevent the need for a forward declaration in the next
commit and to make the review of that commit easier.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are a few MAC/PHYs combinations which now support > 1Gbps. These
may need to make use of link modes with bits > 31. Thus their
supported PHY features or advertised features cannot be implemented
using the current bitmap in a u32. Convert to using a linkmode bitmap,
which can support all the currently devices link modes, and is future
proof as more modes are added.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/broadcom/genet/bcmgenet.c: In function 'bcmgenet_power_down':
drivers/net/ethernet/broadcom/genet/bcmgenet.c:1136:6: warning:
variable 'ret' set but not used [-Wunused-but-set-variable]
bcmgenet_power_down should return 'ret' instead of 0.
Fixes: ca8cf34190 ("net: bcmgenet: propagate errors from bcmgenet_power_down")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A timing hazard exists when the network interface is stopped that
allows a watchdog timeout to be processed by a separate core in
parallel. This creates the potential for the timeout handler to
wake the queues while the driver is shutting down, or access
registers after their clocks have been removed.
The more common case is that the watchdog timeout will produce a
warning message which doesn't lead to a crash. The chances of this
are greatly increased by the fact that bcmgenet_netif_stop stops
the transmit queues which can easily precipitate a watchdog time-
out because of stale trans_start data in the queues.
This commit corrects the behavior by ensuring that the watchdog
timeout is disabled before enterring bcmgenet_netif_stop. There
are currently only two users of the bcmgenet_netif_stop function:
close and suspend.
The close case already handles the issue by exiting the RUNNING
state before invoking the driver close service.
The suspend case now performs the netif_device_detach to exit the
PRESENT state before the call to bcmgenet_netif_stop rather than
after it.
These behaviors prevent any future scheduling of the driver timeout
service during the window. The netif_tx_stop_all_queues function
in bcmgenet_netif_stop is replaced with netif_tx_disable to ensure
synchronization with any transmit or timeout threads that may
already be executing on other cores.
For symmetry, the netif_device_attach call upon resume is moved to
after the call to bcmgenet_netif_start. Since it wakes the transmit
queues it is not necessary to invoke netif_tx_start_all_queues from
bcmgenet_netif_start so it is moved into the driver open service.
Fixes: 1c1008c793 ("net: bcmgenet: add main driver file")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Sync dtc with upstream version v1.4.7-14-gc86da84d30e4
- Work to get rid of direct accesses to struct device_node name and
type pointers in preparation for removing them. New helpers for
parsing DT cpu nodes and conversions to use the helpers. printk
conversions to %pOFn for printing DT node names. Most went thru
subystem trees, so this is the remainder.
- Fixes to DT child node lookups to actually be restricted to child
nodes instead of treewide.
- Refactoring of dtb targets out of arch code. This makes the support
more uniform and enables building all dtbs on c6x, microblaze, and
powerpc.
- Various DT binding updates for Renesas r8a7744 SoC
- Vendor prefixes for Facebook, OLPC
- Restructuring of some ARM binding docs moving some peripheral bindings
out of board/SoC binding files
- New "secure-chosen" binding for secure world settings on ARM
- Dual licensing of 2 DT IRQ binding headers
-----BEGIN PGP SIGNATURE-----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=335v
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull Devicetree updates from Rob Herring:
"A bit bigger than normal as I've been busy this cycle.
There's a few things with dependencies and a few things subsystem
maintainers didn't pick up, so I'm taking them thru my tree.
The fixes from Johan didn't get into linux-next, but they've been
waiting for some time now and they are what's left of what subsystem
maintainers didn't pick up.
Summary:
- Sync dtc with upstream version v1.4.7-14-gc86da84d30e4
- Work to get rid of direct accesses to struct device_node name and
type pointers in preparation for removing them. New helpers for
parsing DT cpu nodes and conversions to use the helpers. printk
conversions to %pOFn for printing DT node names. Most went thru
subystem trees, so this is the remainder.
- Fixes to DT child node lookups to actually be restricted to child
nodes instead of treewide.
- Refactoring of dtb targets out of arch code. This makes the support
more uniform and enables building all dtbs on c6x, microblaze, and
powerpc.
- Various DT binding updates for Renesas r8a7744 SoC
- Vendor prefixes for Facebook, OLPC
- Restructuring of some ARM binding docs moving some peripheral
bindings out of board/SoC binding files
- New "secure-chosen" binding for secure world settings on ARM
- Dual licensing of 2 DT IRQ binding headers"
* tag 'devicetree-for-4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (78 commits)
ARM: dt: relicense two DT binding IRQ headers
power: supply: twl4030-charger: fix OF sibling-node lookup
NFC: nfcmrvl_uart: fix OF child-node lookup
net: stmmac: dwmac-sun8i: fix OF child-node lookup
net: bcmgenet: fix OF child-node lookup
drm/msm: fix OF child-node lookup
drm/mediatek: fix OF sibling-node lookup
of: Add missing exports of node name compare functions
dt-bindings: Add OLPC vendor prefix
dt-bindings: misc: bk4: Add device tree binding for Liebherr's BK4 SPI bus
dt-bindings: thermal: samsung: Add SPDX license identifier
dt-bindings: clock: samsung: Add SPDX license identifiers
dt-bindings: timer: ostm: Add R7S9210 support
dt-bindings: phy: rcar-gen2: Add r8a7744 support
dt-bindings: can: rcar_can: Add r8a7744 support
dt-bindings: timer: renesas, cmt: Document r8a7744 CMT support
dt-bindings: watchdog: renesas-wdt: Document r8a7744 support
dt-bindings: thermal: rcar: Add device tree support for r8a7744
Documentation: dt: Add binding for /secure-chosen/stdout-path
dt-bindings: arm: zte: Move sysctrl bindings to their own doc
...
Use the new of_get_compatible_child() helper to lookup the mdio child
node instead of using of_find_compatible_node(), which searches the
entire tree from a given start node and thus can return an unrelated
(i.e. non-child) node.
This also addresses a potential use-after-free (e.g. after probe
deferral) as the tree-wide helper drops a reference to its first
argument (i.e. the node of the device being probed).
Fixes: aa09677cba ("net: bcmgenet: add MDIO routines")
Cc: stable <stable@vger.kernel.org> # 3.15
Cc: David S. Miller <davem@davemloft.net>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
net/sched/cls_api.c has overlapping changes to a call to
nlmsg_parse(), one (from 'net') added rtm_tca_policy instead of NULL
to the 5th argument, and another (from 'net-next') added cb->extack
instead of NULL to the 6th argument.
net/ipv4/ipmr_base.c is a case of a bug fix in 'net' being done to
code which moved (to mr_table_dump)) in 'net-next'. Thanks to David
Ahern for the heads up.
Signed-off-by: David S. Miller <davem@davemloft.net>
On GENETv5, there is a hardware issue which prevents the GENET hardware
from generating a link UP interrupt when the link is operating at
10Mbits/sec. Since we do not have any way to configure the link
detection logic, fallback to polling in that case.
Fixes: 421380856d ("net: bcmgenet: add support for the GENETv5 hardware")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The phy supported speed is being used to determine if the MAC should
be configured to 100 or 1G. The masking logic is broken. Instead, look
at 1G supported speeds to enable 1G MAC support.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many Ethernet MAC drivers want to limit the PHY to only advertise a
maximum speed of 100Mbs or 1Gbps. Rather than using a mask, make use
of the helper function phy_set_max_speed().
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using the fixed PHY with GENET (e.g. MOCA) the PHY link
status can be determined from the internal link status captured
by the MAC. This allows the PHY state machine to use the correct
link state with the fixed PHY even if MAC link event interrupts
are missed when the net device is opened.
Fixes: 8d88c6ebb3 ("net: bcmgenet: enable MoCA link state change detection")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Preparation for introducing adaptive TX to net DIM.
Signed-off-by: Tal Gilboa <talgi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb->protocol is a __be16 which we would be calling htons() against,
while this is not wrong per-se as it correctly results in swapping the
value on LE hosts, this still upsets sparse. Adopt a similar pattern to
what other drivers do and just assign ip_ver to skb->protocol, and then
use htons() against the different constants such that the compiler can
resolve the values at build time.
Fixes: 1c1008c793 ("net: bcmgenet: add main driver file")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There were a number of issues with setting the RX coalescing parameters:
- we would not be preserving values that would have been configured
across close/open calls, instead we would always reset to no timeout
and 1 interrupt per packet, this would also prevent DIM from setting its
default usec/pkts values
- when adaptive RX would be turned on, we woud not be fetching the
default parameters, we would stay with no timeout/1 packet per interrupt
until the estimator kicks in and changes that
- finally disabling adaptive RX coalescing while providing parameters
would not be honored, and we would stay with whatever DIM had previously
determined instead of the user requested parameters
Fixes: 9f4ca05827 ("net: bcmgenet: Add support for adaptive RX coalescing")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Tal Gilboa <talgi@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following sparse warning:
drivers/net/ethernet/broadcom/genet/bcmgenet.c:1351:16: warning:
Using plain integer as NULL pointer
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unlike the moder modern SYSTEMPORT hardware, we do not have a
configurable TDMA timeout, which limits us to implement adaptive RX
interrupt coalescing only. We have each of our RX rings implement a
bcmgenet_net_dim structure which holds an interrupt counter, number of
packets, bytes, and a container for a net_dim instance.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I see two issues with parameter new_link:
1. It's not needed. See also phy_interrupt(), works w/o this parameter.
phy_mac_interrupt sets the state to PHY_CHANGELINK and triggers the
state machine which then calls phy_read_status. And phy_read_status
updates the link state.
2. phy_mac_interrupt is used in interrupt context and getting the link
state may sleep (at least when having to access the PHY registers
via MDIO bus).
So let's remove it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use BUG_ON instead of if condition followed by BUG.
Something to notice in this particular case is that unlikely()
is already being called inside BUG_ON macro.
This issue was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the software reset of the PHY has been removed it is no
longer necessary to retain a private pointer to the phydev for
use when the PHY is detached (which isn't generally safe anyway).
The driver now uses the phydev member attached to the net_device.
For ethtool commands that have a PHY component, an explicit check
is made to prevent accessing an invalid phydev pointer when one
is not attached (e.g. interface is down).
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With commit f7d72996e222 ("net: bcmgenet: enable loopback during
UniMAC sw_reset") it is no longer necessary to force the software
reset of the internal EPHY before resetting the UniMAC to ensure a
clean reset.
Therefore this commit reverts commit 5dbebbb44a ("net: bcmgenet:
Software reset EPHY after power on").
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the ring locks are not used in a hard IRQ context it is often
not necessary to disable global IRQs while waiting on a lock.
Using less restrictive lock and unlock calls improves the real-time
responsiveness of the system.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
