sh_eth_{suspend|resume}() initialize their local variable 'ret' to 0 but
this value is never really used, thus we can kill those intializers...
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/f09d7c64-4a2b-6973-09a4-10d759ed0df4@omp.ru
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
sh_eth_close() always returns 0, hence the check in sh_eth_wol_restore()
is pointless (however we cannot change the prototype of sh_eth_close() as
it implements the driver's ndo_stop() method).
Found by Linux Verification Center (linuxtesting.org) with the SVACE static
analysis tool.
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
After following the call tree of phy_set_max_speed(), it became clear
that this function never returns anything but 0, so we can change its
result type to *void* and drop the result checks from the three drivers
that actually bothered to do it...
Found by Linux Verification Center (linuxtesting.org) with the SVACE static
analysis tool.
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add two new parameters kernel_ringparam and extack for
.get_ringparam and .set_ringparam to extend more ring params
through netlink.
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 406f42fa0d ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Break the address up into an array on the stack, then call
eth_hw_addr_set().
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert all Ethernet drivers from memcpy(... ETH_ADDR)
to eth_hw_addr_set():
@@
expression dev, np;
@@
- memcpy(dev->dev_addr, np, ETH_ALEN)
+ eth_hw_addr_set(dev, np)
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cur_tx counter must be incremented after TACT bit of
txdesc->status was set. However, a CPU is possible to reorder
instructions and/or memory accesses between cur_tx and
txdesc->status. And then, if TX interrupt happened at such a
timing, the sh_eth_tx_free() may free the descriptor wrongly.
So, add wmb() before cur_tx++.
Otherwise NETDEV WATCHDOG timeout is possible to happen.
Fixes: 86a74ff21a ("net: sh_eth: add support for Renesas SuperH Ethernet")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most users of ndo_do_ioctl are ethernet drivers that implement
the MII commands SIOCGMIIPHY/SIOCGMIIREG/SIOCSMIIREG, or hardware
timestamping with SIOCSHWTSTAMP/SIOCGHWTSTAMP.
Separate these from the few drivers that use ndo_do_ioctl to
implement SIOCBOND, SIOCBR and SIOCWANDEV commands.
This is a purely cosmetic change intended to help readers find
their way through the implementation.
Cc: Doug Ledford <dledford@redhat.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Vladimir Oltean <olteanv@gmail.com>
Cc: Leon Romanovsky <leon@kernel.org>
Cc: linux-rdma@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial conflicts in net/can/isotp.c and
tools/testing/selftests/net/mptcp/mptcp_connect.sh
scaled_ppm_to_ppb() was moved from drivers/ptp/ptp_clock.c
to include/linux/ptp_clock_kernel.h in -next so re-apply
the fix there.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In preparation for FORTIFY_SOURCE performing compile-time and run-time
field bounds checking for memcpy(), memmove(), and memset(), avoid
intentionally reading across neighboring array fields.
The memcpy() is copying the entire structure, not just the first array.
Adjust the source argument so the compiler can do appropriate bounds
checking.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use devm_platform_get_and_ioremap_resource() to simplify
code.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_get_mac_address() returns a "const void*" pointer to a MAC address.
Lately, support to fetch the MAC address by an NVMEM provider was added.
But this will only work with platform devices. It will not work with
PCI devices (e.g. of an integrated root complex) and esp. not with DSA
ports.
There is an of_* variant of the nvmem binding which works without
devices. The returned data of a nvmem_cell_read() has to be freed after
use. On the other hand the return of_get_mac_address() points to some
static data without a lifetime. The trick for now, was to allocate a
device resource managed buffer which is then returned. This will only
work if we have an actual device.
Change it, so that the caller of of_get_mac_address() has to supply a
buffer where the MAC address is written to. Unfortunately, this will
touch all drivers which use the of_get_mac_address().
Usually the code looks like:
const char *addr;
addr = of_get_mac_address(np);
if (!IS_ERR(addr))
ether_addr_copy(ndev->dev_addr, addr);
This can then be simply rewritten as:
of_get_mac_address(np, ndev->dev_addr);
Sometimes is_valid_ether_addr() is used to test the MAC address.
of_get_mac_address() already makes sure, it just returns a valid MAC
address. Thus we can just test its return code. But we have to be
careful if there are still other sources for the MAC address before the
of_get_mac_address(). In this case we have to keep the
is_valid_ether_addr() call.
The following coccinelle patch was used to convert common cases to the
new style. Afterwards, I've manually gone over the drivers and fixed the
return code variable: either used a new one or if one was already
available use that. Mansour Moufid, thanks for that coccinelle patch!
<spml>
@a@
identifier x;
expression y, z;
@@
- x = of_get_mac_address(y);
+ x = of_get_mac_address(y, z);
<...
- ether_addr_copy(z, x);
...>
@@
identifier a.x;
@@
- if (<+... x ...+>) {}
@@
identifier a.x;
@@
if (<+... x ...+>) {
...
}
- else {}
@@
identifier a.x;
expression e;
@@
- if (<+... x ...+>@e)
- {}
- else
+ if (!(e))
{...}
@@
expression x, y, z;
@@
- x = of_get_mac_address(y, z);
+ of_get_mac_address(y, z);
... when != x
</spml>
All drivers, except drivers/net/ethernet/aeroflex/greth.c, were
compile-time tested.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
In all the SoC manuals (except R-Car gen2) the PHY status register's name
is abbreviated to PSR with the only valid bit 0 named LMON. Follow the
suit and rename the corresponding *enum* tag/entry.
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
In all the SoC manuals the TRSCER register bits match the corresponding
EESR registers's bits, but only on the R-Car gen2 SoC those are named
RINT<n> and TINT<n>. Follow the suit and rename the *enum* tag/entries
from DESC_I_* to TRSCER_*.
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the RZ/A2M Group User's Manual: Hardware, Rev. 2.00,
the TRSCER register has bit 9 reserved, hence we can't use the driver's
default TRSCER mask. Add the explicit initializer for sh_eth_cpu_data::
trscer_err_mask for R7S9210.
Fixes: 6e0bb04d0e ("sh_eth: Add R7S9210 support")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the RZ/A1H Group, RZ/A1M Group User's Manual: Hardware,
Rev. 4.00, the TRSCER register has bit 9 reserved, hence we can't use
the driver's default TRSCER mask. Add the explicit initializer for
sh_eth_cpu_data::trscer_err_mask for R7S72100.
Fixes: db893473d3 ("sh_eth: Add support for r7s72100")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the SH7710, SH7712, SH7713 Group User's Manual: Hardware,
Rev. 3.00, the TRSCER register actually has only bit 7 valid (and named
differently), with all the other bits reserved. Apparently, this was not
the case with some early revisions of the manual as we have the other
bits declared (and set) in the original driver. Follow the suit and add
the explicit sh_eth_cpu_data::trscer_err_mask initializer for SH771x...
Fixes: 86a74ff21a ("net: sh_eth: add support for Renesas SuperH Ethernet")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
sh_eth_close() does a synchronous power down of the device before
marking it closed. Revert the order, to make sure the device is never
marked opened while suspended.
While at it, use pm_runtime_put() instead of pm_runtime_put_sync(), as
there is no reason to do a synchronous power down.
Fixes: 7fa2955ff7 ("sh_eth: Fix sleeping function called from invalid context")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20210118150812.796791-1-geert+renesas@glider.be
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Wolfram reports that his R-Car H2-based Lager board can no longer be
rebooted in v5.11-rc1, as it crashes with an imprecise external abort.
The issue can be reproduced on other boards (e.g. Koelsch with R-Car
M2-W) too, if CONFIG_IP_PNP is disabled, and the Ethernet interface is
down at reboot time:
Unhandled fault: imprecise external abort (0x1406) at 0x00000000
pgd = (ptrval)
[00000000] *pgd=422b6835, *pte=00000000, *ppte=00000000
Internal error: : 1406 [#1] ARM
Modules linked in:
CPU: 0 PID: 1105 Comm: init Tainted: G W 5.10.0-rc1-00402-ge2f016cf7751 #1048
Hardware name: Generic R-Car Gen2 (Flattened Device Tree)
PC is at sh_mdio_ctrl+0x44/0x60
LR is at sh_mmd_ctrl+0x20/0x24
...
Backtrace:
[<c0451f30>] (sh_mdio_ctrl) from [<c0451fd4>] (sh_mmd_ctrl+0x20/0x24)
r7:0000001f r6:00000020 r5:00000002 r4:c22a1dc4
[<c0451fb4>] (sh_mmd_ctrl) from [<c044fc18>] (mdiobb_cmd+0x38/0xa8)
[<c044fbe0>] (mdiobb_cmd) from [<c044feb8>] (mdiobb_read+0x58/0xdc)
r9:c229f844 r8:c0c329dc r7:c221e000 r6:00000001 r5:c22a1dc4 r4:00000001
[<c044fe60>] (mdiobb_read) from [<c044c854>] (__mdiobus_read+0x74/0xe0)
r7:0000001f r6:00000001 r5:c221e000 r4:c221e000
[<c044c7e0>] (__mdiobus_read) from [<c044c9d8>] (mdiobus_read+0x40/0x54)
r7:0000001f r6:00000001 r5:c221e000 r4:c221e458
[<c044c998>] (mdiobus_read) from [<c044d678>] (phy_read+0x1c/0x20)
r7:ffffe000 r6:c221e470 r5:00000200 r4:c229f800
[<c044d65c>] (phy_read) from [<c044d94c>] (kszphy_config_intr+0x44/0x80)
[<c044d908>] (kszphy_config_intr) from [<c044694c>] (phy_disable_interrupts+0x44/0x50)
r5:c229f800 r4:c229f800
[<c0446908>] (phy_disable_interrupts) from [<c0449370>] (phy_shutdown+0x18/0x1c)
r5:c229f800 r4:c229f804
[<c0449358>] (phy_shutdown) from [<c040066c>] (device_shutdown+0x168/0x1f8)
[<c0400504>] (device_shutdown) from [<c013de44>] (kernel_restart_prepare+0x3c/0x48)
r9:c22d2000 r8:c0100264 r7:c0b0d034 r6:00000000 r5:4321fedc r4:00000000
[<c013de08>] (kernel_restart_prepare) from [<c013dee0>] (kernel_restart+0x1c/0x60)
[<c013dec4>] (kernel_restart) from [<c013e1d8>] (__do_sys_reboot+0x168/0x208)
r5:4321fedc r4:01234567
[<c013e070>] (__do_sys_reboot) from [<c013e2e8>] (sys_reboot+0x18/0x1c)
r7:00000058 r6:00000000 r5:00000000 r4:00000000
[<c013e2d0>] (sys_reboot) from [<c0100060>] (ret_fast_syscall+0x0/0x54)
As of commit e2f016cf77 ("net: phy: add a shutdown procedure"),
system reboot calls phy_disable_interrupts() during shutdown. As this
happens unconditionally, the PHY registers may be accessed while the
device is suspended, causing undefined behavior, which may crash the
system.
Fix this by wrapping the PHY bitbang accessors in the sh_eth driver by
wrappers that take care of Runtime PM, to resume the device when needed.
Reported-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
While fixing the W=1 builds, this warning came up because the
developers used a very tricky way to get structures initialized
to a non-zero value, but this causes GCC to warn about an
override. In this case the override was intentional, so just
disable the warning for this code with a kernel macro that results
in disabling the warning for compiles on GCC versions after 8.
It is not appropriate to change the struct to initialize all the
values as it will just add a lot more code for no value. The code
is completely correct as is, we just want to acknowledge that
this code could generate a warning and we're ok with that.
NOTE: the __diag_ignore macro currently only accepts a second
argument of 8 (version 80000), it's either use this one or
open code the pragma.
Fixed Warnings example (all the same):
drivers/net/ethernet/renesas/sh_eth.c:51:12: warning: initialized field overwritten [-Woverride-init]
drivers/net/ethernet/renesas/sh_eth.c:52:12: warning: initialized field overwritten [-Woverride-init]
drivers/net/ethernet/renesas/sh_eth.c:53:13: warning: initialized field overwritten [-Woverride-init]
+ 256 more...
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only usage of bb_ops is to assign its address to the ops field in
the mdiobb_ctrl struct, which is a const pointer. Make it const to allow
the compiler to put it in read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The method ndo_start_xmit() returns a value of type netdev_tx_t. Fix
the ndo function to use the correct type.
Signed-off-by: Yunjian Wang <wangyunjian@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The register maps for the Gigabit controllers and the Ether one used on
RZ/A1 (AKA R7S72100) are identical except for GECMR which is only present
on the true GEther controllers. We no longer use the register map arrays
to determine if a given register exists, and have added the GECMR flag to
the 'struct sh_eth_cpu_data' in the previous patch, so we're ready to drop
the R7S72100 specific register map -- this saves 216 bytes of object code
(ARM gcc 4.8.5).
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Tested-by: Chris Brandt <chris.brandt@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not all Ether controllers having the Gigabit register layout have GECMR --
RZ/A1 (AKA R7S72100) actually has the same layout but no Gigabit speed
support and hence no GECMR. In the past, the new register map table was
added for this SoC, now I think we should have used the existing Gigabit
table with the differences (such as GECMR) covered by the mere flags in
the 'struct sh_eth_cpu_data'. Add such flag for GECMR -- and then we can
get rid of the R7S72100 specific layout in the next patch...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Tested-by: Chris Brandt <chris.brandt@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When adding the sh_eth_cpu_data::no_xdfar flag I forgot to add the flag
check to __sh_eth_get_regs(), causing the non-existing RDFAR/TDFAR to be
considered for dumping on the R-Car gen1/2 SoCs (the register offset check
has the final say here)...
Fixes: 4c1d45850d ("sh_eth: add sh_eth_cpu_data::cexcr flag")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Tested-by: Chris Brandt <chris.brandt@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When adding the sh_eth_cpu_data::cexcr flag I forgot to add the flag
check to __sh_eth_get_regs(), causing the non-existing RX packet counter
registers to be considered for dumping on the R7S72100 SoC (the register
offset sanity check has the final say here)...
Fixes: 4c1d45850d ("sh_eth: add sh_eth_cpu_data::cexcr flag")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Tested-by: Chris Brandt <chris.brandt@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When adding the sh_eth_cpu_data::no_tx_cntrs flag I forgot to add the
flag check to __sh_eth_get_regs(), causing the non-existing TX counter
registers to be considered for dumping on the R7S72100 SoC (the register
offset sanity check has the final say here)...
Fixes: ce9134dff6 ("sh_eth: add sh_eth_cpu_data::no_tx_cntrs flag")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Tested-by: Chris Brandt <chris.brandt@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert suitable drivers to use new helper phy_do_ioctl_running.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Timur Tabi <timur@kernel.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When adding the sh_eth_cpu_data::dual_port flag I forgot to add the flag
checks to __sh_eth_get_regs(), causing the non-existing TSU registers to
be dumped by 'ethtool' on the single port Ether controllers having TSU...
Fixes: a94cf2a614 ("sh_eth: fix TSU init on SH7734/R8A7740")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before this change of_get_phy_mode() returned an enum,
phy_interface_t. On error, -ENODEV etc, is returned. If the result of
the function is stored in a variable of type phy_interface_t, and the
compiler has decided to represent this as an unsigned int, comparision
with -ENODEV etc, is a signed vs unsigned comparision.
Fix this problem by changing the API. Make the function return an
error, or 0 on success, and pass a pointer, of type phy_interface_t,
where the phy mode should be stored.
v2:
Return with *interface set to PHY_INTERFACE_MODE_NA on error.
Add error checks to all users of of_get_phy_mode()
Fixup a few reverse christmas tree errors
Fixup a few slightly malformed reverse christmas trees
v3:
Fix 0-day reported errors.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sh_eth_close() resets the MAC and then calls phy_stop()
so that mdio read access result is incorrect without any error
according to kernel trace like below:
ifconfig-216 [003] .n.. 109.133124: mdio_access: ee700000.ethernet-ffffffff read phy:0x01 reg:0x00 val:0xffff
According to the hardware manual, the RMII mode should be set to 1
before operation the Ethernet MAC. However, the previous code was not
set to 1 after the driver issued the soft_reset in sh_eth_dev_exit()
so that the mdio read access result seemed incorrect. To fix the issue,
this patch adds a condition and set the RMII mode register in
sh_eth_dev_exit() for R-Car Gen2 and RZ/A1 SoCs.
Note that when I have tried to move the sh_eth_dev_exit() calling
after phy_stop() on sh_eth_close(), but it gets worse (kernel panic
happened and it seems that a register is accessed while the clock is
off).
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes following (similar) warning reported by kbuild test robot:
In function ‘memcpy’,
inlined from ‘smsc75xx_init_mac_address’ at drivers/net/usb/smsc75xx.c:778:3,
inlined from ‘smsc75xx_bind’ at drivers/net/usb/smsc75xx.c:1501:2:
./include/linux/string.h:355:9: warning: argument 2 null where non-null expected [-Wnonnull]
return __builtin_memcpy(p, q, size);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/usb/smsc75xx.c: In function ‘smsc75xx_bind’:
./include/linux/string.h:355:9: note: in a call to built-in function ‘__builtin_memcpy’
I've replaced the offending memcpy with ether_addr_copy, because I'm
100% sure, that of_get_mac_address can't return NULL as it returns valid
pointer or ERR_PTR encoded value, nothing else.
I'm hesitant to just change IS_ERR into IS_ERR_OR_NULL check, as this
would make the warning disappear also, but it would be confusing to
check for impossible return value just to make a compiler happy.
I'm now changing all occurencies of memcpy to ether_addr_copy after the
of_get_mac_address call, as it's very likely, that we're going to get
similar reports from kbuild test robot in the future.
Fixes: a51645f70f ("net: ethernet: support of_get_mac_address new ERR_PTR error")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
"Highlights:
1) Support AES128-CCM ciphers in kTLS, from Vakul Garg.
2) Add fib_sync_mem to control the amount of dirty memory we allow to
queue up between synchronize RCU calls, from David Ahern.
3) Make flow classifier more lockless, from Vlad Buslov.
4) Add PHY downshift support to aquantia driver, from Heiner
Kallweit.
5) Add SKB cache for TCP rx and tx, from Eric Dumazet. This reduces
contention on SLAB spinlocks in heavy RPC workloads.
6) Partial GSO offload support in XFRM, from Boris Pismenny.
7) Add fast link down support to ethtool, from Heiner Kallweit.
8) Use siphash for IP ID generator, from Eric Dumazet.
9) Pull nexthops even further out from ipv4/ipv6 routes and FIB
entries, from David Ahern.
10) Move skb->xmit_more into a per-cpu variable, from Florian
Westphal.
11) Improve eBPF verifier speed and increase maximum program size,
from Alexei Starovoitov.
12) Eliminate per-bucket spinlocks in rhashtable, and instead use bit
spinlocks. From Neil Brown.
13) Allow tunneling with GUE encap in ipvs, from Jacky Hu.
14) Improve link partner cap detection in generic PHY code, from
Heiner Kallweit.
15) Add layer 2 encap support to bpf_skb_adjust_room(), from Alan
Maguire.
16) Remove SKB list implementation assumptions in SCTP, your's truly.
17) Various cleanups, optimizations, and simplifications in r8169
driver. From Heiner Kallweit.
18) Add memory accounting on TX and RX path of SCTP, from Xin Long.
19) Switch PHY drivers over to use dynamic featue detection, from
Heiner Kallweit.
20) Support flow steering without masking in dpaa2-eth, from Ioana
Ciocoi.
21) Implement ndo_get_devlink_port in netdevsim driver, from Jiri
Pirko.
22) Increase the strict parsing of current and future netlink
attributes, also export such policies to userspace. From Johannes
Berg.
23) Allow DSA tag drivers to be modular, from Andrew Lunn.
24) Remove legacy DSA probing support, also from Andrew Lunn.
25) Allow ll_temac driver to be used on non-x86 platforms, from Esben
Haabendal.
26) Add a generic tracepoint for TX queue timeouts to ease debugging,
from Cong Wang.
27) More indirect call optimizations, from Paolo Abeni"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1763 commits)
cxgb4: Fix error path in cxgb4_init_module
net: phy: improve pause mode reporting in phy_print_status
dt-bindings: net: Fix a typo in the phy-mode list for ethernet bindings
net: macb: Change interrupt and napi enable order in open
net: ll_temac: Improve error message on error IRQ
net/sched: remove block pointer from common offload structure
net: ethernet: support of_get_mac_address new ERR_PTR error
net: usb: smsc: fix warning reported by kbuild test robot
staging: octeon-ethernet: Fix of_get_mac_address ERR_PTR check
net: dsa: support of_get_mac_address new ERR_PTR error
net: dsa: sja1105: Fix status initialization in sja1105_get_ethtool_stats
vrf: sit mtu should not be updated when vrf netdev is the link
net: dsa: Fix error cleanup path in dsa_init_module
l2tp: Fix possible NULL pointer dereference
taprio: add null check on sched_nest to avoid potential null pointer dereference
net: mvpp2: cls: fix less than zero check on a u32 variable
net_sched: sch_fq: handle non connected flows
net_sched: sch_fq: do not assume EDT packets are ordered
net: hns3: use devm_kcalloc when allocating desc_cb
net: hns3: some cleanup for struct hns3_enet_ring
...
There was NVMEM support added to of_get_mac_address, so it could now
return ERR_PTR encoded error values, so we need to adjust all current
users of of_get_mac_address to this new fact.
While at it, remove superfluous is_valid_ether_addr as the MAC address
returned from of_get_mac_address is always valid and checked by
is_valid_ether_addr anyway.
Fixes: d01f449c00 ("of_net: add NVMEM support to of_get_mac_address")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
mmiowb() is now implied by spin_unlock() on architectures that require
it, so there is no reason to call it from driver code. This patch was
generated using coccinelle:
@mmiowb@
@@
- mmiowb();
and invoked as:
$ for d in drivers include/linux/qed sound; do \
spatch --include-headers --sp-file mmiowb.cocci --dir $d --in-place; done
NOTE: mmiowb() has only ever guaranteed ordering in conjunction with
spin_unlock(). However, pairing each mmiowb() removal in this patch with
the corresponding call to spin_unlock() is not at all trivial, so there
is a small chance that this change may regress any drivers incorrectly
relying on mmiowb() to order MMIO writes between CPUs using lock-free
synchronisation. If you've ended up bisecting to this commit, you can
reintroduce the mmiowb() calls using wmb() instead, which should restore
the old behaviour on all architectures other than some esoteric ia64
systems.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
of_get_phy_mode may fail and return a negative error code;
the fix checks the return value of of_get_phy_mode and
returns NULL of it fails.
Fixes: b356e978e9 ("sh_eth: add device tree support")
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SH7763 SoC manual describes the Ether MAC's RX checksum offload
the same way as it's implemented in the EtherAVB MACs...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SH7734 SoC manual describes the Ether MAC's RX checksum offload
the same way as it's implemented in the EtherAVB MACs...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The R-Car V3H (R8A77980) SoC manual describes the Ether MAC's RX checksum
offload the same way as it's implemented in the EtherAVB MAC...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The R-Mobile A1 (R8A7740) SoC manual describes the Ether MAC's RX checksum
offload the same way as it's implemented in the EtherAVB MAC...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RZ/A1H (R7S721000) SoC manual describes the Ether MAC's RX checksum
offload the same way as it's implemented in the EtherAVB MACs...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the RX checksum offload. This is enabled by default and
may be disabled and re-enabled using 'ethtool':
# ethtool -K eth0 rx off
# ethtool -K eth0 rx on
Some Ether MACs provide a simple checksumming scheme which appears to be
completely compatible with CHECKSUM_COMPLETE: sum of all packet data after
the L2 header is appended to packet data; this may be trivially read by
the driver and used to update the skb accordingly. The same checksumming
scheme is implemented in the EtherAVB MACs and now supported by the 'ravb'
driver.
In terms of performance, throughput is close to gigabit line rate with the
RX checksum offload both enabled and disabled. The 'perf' output, however,
appears to indicate that significantly less time is spent in do_csum() --
this is as expected.
Test results with RX checksum offload enabled:
~/netperf-2.2pl4# perf record -a ./netperf -t TCP_MAERTS -H 192.168.2.4
TCP MAERTS TEST to 192.168.2.4
Recv Send Send
Socket Socket Message Elapsed
Size Size Size Time Throughput
bytes bytes bytes secs. 10^6bits/sec
131072 16384 16384 10.01 933.93
[ perf record: Woken up 8 times to write data ]
[ perf record: Captured and wrote 1.955 MB perf.data (41940 samples) ]
~/netperf-2.2pl4# perf report
Samples: 41K of event 'cycles:ppp', Event count (approx.): 9915302763
Overhead Command Shared Object Symbol
9.44% netperf [kernel.kallsyms] [k] __arch_copy_to_user
7.75% swapper [kernel.kallsyms] [k] _raw_spin_unlock_irq
6.31% swapper [kernel.kallsyms] [k] default_idle_call
5.89% swapper [kernel.kallsyms] [k] arch_cpu_idle
4.37% swapper [kernel.kallsyms] [k] tick_nohz_idle_exit
4.02% netperf [kernel.kallsyms] [k] _raw_spin_unlock_irq
2.52% netperf [kernel.kallsyms] [k] preempt_count_sub
1.81% netperf [kernel.kallsyms] [k] tcp_recvmsg
1.80% netperf [kernel.kallsyms] [k] _raw_spin_unlock_irqres
1.78% netperf [kernel.kallsyms] [k] preempt_count_add
1.36% netperf [kernel.kallsyms] [k] __tcp_transmit_skb
1.20% netperf [kernel.kallsyms] [k] __local_bh_enable_ip
1.10% netperf [kernel.kallsyms] [k] sh_eth_start_xmit
Test results with RX checksum offload disabled:
~/netperf-2.2pl4# perf record -a ./netperf -t TCP_MAERTS -H 192.168.2.4
TCP MAERTS TEST to 192.168.2.4
Recv Send Send
Socket Socket Message Elapsed
Size Size Size Time Throughput
bytes bytes bytes secs. 10^6bits/sec
131072 16384 16384 10.01 932.04
[ perf record: Woken up 14 times to write data ]
[ perf record: Captured and wrote 3.642 MB perf.data (78817 samples) ]
~/netperf-2.2pl4# perf report
Samples: 78K of event 'cycles:ppp', Event count (approx.): 18091442796
Overhead Command Shared Object Symbol
7.00% swapper [kernel.kallsyms] [k] do_csum
3.94% swapper [kernel.kallsyms] [k] sh_eth_poll
3.83% ksoftirqd/0 [kernel.kallsyms] [k] do_csum
3.23% swapper [kernel.kallsyms] [k] _raw_spin_unlock_irq
2.87% netperf [kernel.kallsyms] [k] __arch_copy_to_user
2.86% swapper [kernel.kallsyms] [k] arch_cpu_idle
2.13% swapper [kernel.kallsyms] [k] default_idle_call
2.12% ksoftirqd/0 [kernel.kallsyms] [k] sh_eth_poll
2.02% swapper [kernel.kallsyms] [k] _raw_spin_unlock_irqrestore
1.84% swapper [kernel.kallsyms] [k] __softirqentry_text_start
1.64% swapper [kernel.kallsyms] [k] tick_nohz_idle_exit
1.53% netperf [kernel.kallsyms] [k] _raw_spin_unlock_irq
1.32% netperf [kernel.kallsyms] [k] preempt_count_sub
1.27% swapper [kernel.kallsyms] [k] __pi___inval_dcache_area
1.22% swapper [kernel.kallsyms] [k] check_preemption_disabled
1.01% ksoftirqd/0 [kernel.kallsyms] [k] _raw_spin_unlock_irqrestore
The above results collected on the R-Car V3H Starter Kit board.
Based on the commit 4d86d38186 ("ravb: RX checksum offload")...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 62e04b7e0e ("sh_eth: rename 'sh_eth_cpu_data::hw_crc'") renamed
the field to 'hw_checksum' for the Ether DMAC "intelligent checksum",
however some Ether MACs implement a simpler checksumming scheme, so that
name now seems misleading. Rename that field to 'csmr' as the "intelligent
checksum" is always controlled by the CSMR register.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the R7S9210 which is part of the RZ/A2 series.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
sh_eth_tsu_read_entry() is still asymmetric with sh_eth_tsu_write_entry()
WRT their prototypes -- make them symmetric by passing to the former a TSU
register offset instead of its address and also adding the (now necessary)
'ndev' parameter...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can add the TSU register base address to a TSU register offset right
in sh_eth_tsu_write_entry(), no need to do it in its callers...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
