Clang does not support this option so the build fails:
error: unknown warning option '-Wno-dangling-pointer' [-Werror,-Wunknown-warning-option]
Use cc-disable-warning so that the option is only added when it is
supported.
Fixes: bd1d129daa ("wifi: ath6k: silence false positive -Wno-dangling-pointer warning on GCC 12")
Reported-by: "kernelci.org bot" <bot@kernelci.org>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Tom Rix <trix@redhat.com>
Link: https://lore.kernel.org/r/20220524145655.869822-1-nathan@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
carl9170 has a big union (struct carl9170_cmd) with all the command
types in it. But it allocates buffers only large enough for a given
command. This upsets GCC 12:
drivers/net/wireless/ath/carl9170/cmd.c:125:30: warning: array subscript ‘struct carl9170_cmd[0]’ is partly outside array bounds of ‘unsigned char[8]’ [-Warray-bounds]
125 | tmp->hdr.cmd = cmd;
| ~~~~~~~~~~~~~^~~~~
Punt the warning to W=1 for now. Hopefully GCC will learn to
recognize which fields are in-bounds.
Acked-by: Christian Lamparter <chunkeey@gmail.com>
Acked-by: Kalle Valo <kvalo@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
For some reason GCC 12 decided to complain about the common
pattern of queuing an object onto a list on the stack in ath6k:
inlined from ‘ath6kl_htc_mbox_tx’ at drivers/net/wireless/ath/ath6kl/htc_mbox.c:1142:3:
include/linux/list.h:74:19: warning: storing the address of local variable ‘queue’ in ‘*&packet_15(D)->list.prev’ [-Wdangling-pointer=]
74 | new->prev = prev;
| ~~~~~~~~~~^~~~~~
Move the warning to W=1, hopefully it goes away with a compiler
update.
Acked-by: Kalle Valo <kvalo@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
GCC 12 says:
drivers/net/wireless/ath/ath9k/mac.c: In function ‘ath9k_hw_resettxqueue’:
drivers/net/wireless/ath/ath9k/mac.c:373:22: warning: array subscript 32 is above array bounds of ‘struct ath9k_tx_queue_info[10]’ [-Warray-bounds]
373 | qi = &ah->txq[q];
| ~~~~~~~^~~
I don't know where it got the 32 from, relegate the warning to W=1+.
Acked-by: Kalle Valo <kvalo@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch adds the new struct ieee80211_rate_status and replaces
'struct rate_info *rate' in ieee80211_tx_status with pointer and length
annotation.
The struct ieee80211_rate_status allows to:
(1) receive tx power status feedback for transmit power control (TPC)
per packet or packet retry
(2) dynamic mapping of wifi chip specific multi-rate retry (mrr)
chains with different lengths
(3) increase the limit of annotatable rate indices to support
IEEE802.11ac rate sets and beyond
ieee80211_tx_info, control and status buffer, and ieee80211_tx_rate
cannot be used to achieve these goals due to fixed size limitations.
Our new struct contains a struct rate_info to annotate the rate that was
used, retry count of the rate and tx power. It is intended for all
information related to RC and TPC that needs to be passed from driver to
mac80211 and its RC/TPC algorithms like Minstrel_HT. It corresponds to
one stage in an mrr. Multiple subsequent instances of this struct can be
included in struct ieee80211_tx_status via a pointer and a length variable.
Those instances can be allocated on-stack. The former reference to a single
instance of struct rate_info is replaced with our new annotation.
An extension is introduced to struct ieee80211_hw. There are two new
members called 'tx_power_levels' and 'max_txpwr_levels_idx' acting as a
tx power level table. When a wifi device is registered, the driver shall
supply all supported power levels in this list. This allows to support
several quirks like differing power steps in power level ranges or
alike. TPC can use this for algorithm and thus be designed more abstract
instead of handling all possible step widths individually.
Further mandatory changes in status.c, mt76 and ath11k drivers due to the
removal of 'struct rate_info *rate' are also included.
status.c already uses the information in ieee80211_tx_status->rate in
radiotap, this is now changed to use ieee80211_rate_status->rate_idx.
mt76 driver already uses struct rate_info to pass the tx rate to status
path. The new members of the ieee80211_tx_status are set to NULL and 0
because the previously passed rate is not relevant to rate control and
accurate information is passed via tx_info->status.rates.
For ath11k, the txrate can be passed via this struct because ath11k uses
firmware RC and thus the information does not interfere with software RC.
Compile-Tested: current wireless-next tree with all flags on
Tested-on: Xiaomi 4A Gigabit (MediaTek MT7603E, MT7612E) with OpenWrt
Linux 5.10.113
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://lore.kernel.org/r/20220509173958.1398201-2-jelonek.jonas@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The variables vht_mcs and he_mcs are being initialized in the
start of for-loops however they are re-assigned new values in
the loop and not used outside the loop. The initializations
are redundant and can be removed.
Cleans up clang scan warnings:
warning: Although the value stored to 'vht_mcs' is used in the
enclosing expression, the value is never actually read from
'vht_mcs' [deadcode.DeadStores]
warning: Although the value stored to 'he_mcs' is used in the
enclosing expression, the value is never actually read from
'he_mcs' [deadcode.DeadStores]
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220507184155.26939-1-colin.i.king@gmail.com
Ath11k allocates memory when firmware requests memory in QMI.
Coldboot calibration and firmware recovery uses firmware reload.
On firmware reload, firmware sends memory request again. If Ath11k
allocates memory on first firmware boot, reuse the available
memory. Also check if the segment type and size is same
on the next firmware boot. Reuse if segment type/size is
same as previous firmware boot else free the segment and
allocate the segment with size/type.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.6.0.1-00752-QCAHKSWPL_SILICONZ-1
Signed-off-by: Anilkumar Kolli <quic_akolli@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220506141448.10340-1-quic_akolli@quicinc.com
In case of Passpoint, the WLAN interface may be requested to
remain on a specific channel and then to send some management
frames on that channel. Now chanfreq of wmi_mgmt_send_cmd is set
as 0, as a result firmware may choose a default but wrong channel.
Fix it by assigning chanfreq field with the designated channel.
This change only applies to WCN6855 and QCA6390, other chips are
not affected.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220506013614.1580274-4-quic_bqiang@quicinc.com
Commit 66307ca040 ("ath11k: fix mgmt_tx_wmi cmd sent to FW for
deleted vdev") wants both of below two conditions are true before
sending management frames:
1: ar->allocated_vdev_map & (1LL << arvif->vdev_id)
2: arvif->is_started
Actually the second one is not necessary because with the first one
we can make sure the vdev is present.
Also use ar->conf_mutex to synchronize vdev delete and mgmt. TX.
This issue is found in case of Passpoint scenario where ath11k
needs to send action frames before vdev is started.
Fix it by removing the second condition.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Fixes: 66307ca040 ("ath11k: fix mgmt_tx_wmi cmd sent to FW for deleted vdev")
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220506013614.1580274-3-quic_bqiang@quicinc.com
Add remain on channel support, it is needed in several
scenarios such as Passpoint etc.
Currently this is supported by QCA6390, WCN6855, IPQ8074,
IPQ6018 and QCN9074.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220506013614.1580274-2-quic_bqiang@quicinc.com
With WoWLAN enabled and after sleeping for a rather long time,
we are seeing that with some APs, it is not able to wake up
the STA though the correct wake up pattern has been configured.
This is because the host doesn't send keepalive command to
firmware, thus firmware will not send any packet to the AP and
after a specific time the AP kicks out the STA.
Fix this issue by enabling keepalive before going to suspend
and disabling it after resume back.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220506012540.1579604-1-quic_bqiang@quicinc.com
When doing simulate_fw_crash operation periodically with a short interval
time such as 10 seconds, it is easy happened WMI command timed out for
WMI_SCAN_CHAN_LIST_CMDID in ath11k_reg_update_chan_list().
log:
[42287.610053] ath11k_pci 0000:01:00.0: wmi command 12291 timeout
[42287.610064] ath11k_pci 0000:01:00.0: failed to send WMI_SCAN_CHAN_LIST cmd
[42287.610073] ath11k_pci 0000:01:00.0: failed to perform regd update : -11
Note that this issue does not occur with a longer interval such as 20 seconds.
The reason the issue occurs with a shorter interval is the following steps:
1) Upon initial boot, or after device recovery, the initial hw scan plus
the 11d scan will run, and when 6 GHz support is present, these scans
can take up to 12 seconds to complete, so ath11k_reg_update_chan_list()
is still waiting the completion of ar->completed_11d_scan.
2) If a simulate_fw_crash operation is received during this time, those
scans do not complete, and ath11k_core_pre_reconfigure_recovery()
complete the ar->completed_11d_scan, then ath11k_reg_update_chan_list()
wakeup and start to send WMI_SCAN_CHAN_LIST_CMDID, but firmware is crashed
at this moment, so wmi timed out occur.
To address this issue, reset the 11d state during device recovery so that
WMI_SCAN_CHAN_LIST_CMDID does not timed out for short interval time such
as 10 seconds.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3
Fixes: 1f682dc9fb ("ath11k: reduce the wait time of 11d scan and hw scan while add interface")
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220505034636.29582-1-quic_wgong@quicinc.com
The offset of REO register where the RX fragment destination ring
is configured is different in WCN6750 as compared to WCN6855.
Due to this differnce in offsets, on WCN6750, fragment destination
ring will be configured incorrectly, leading to RX fragments not
getting delivered to the driver. Fix this by defining HW specific
offsets for the REO MISC CTL register.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220504083900.31513-1-quic_mpubbise@quicinc.com
Some ath10k IPQ40xx devices like the MikroTik hAP ac2 and ac3 require the
BDF-s to be extracted from the device storage instead of shipping packaged
API 2 BDF-s.
This is required as MikroTik has started shipping boards that require BDF-s
to be updated, as otherwise their WLAN performance really suffers.
This is however impossible as the devices that require this are release
under the same revision and its not possible to differentiate them from
devices using the older BDF-s.
In OpenWrt we are extracting the calibration data during runtime and we are
able to extract the BDF-s in the same manner, however we cannot package the
BDF-s to API 2 format on the fly and can only use API 1 to provide BDF-s on
the fly.
This is an issue as the ath10k driver explicitly looks only for the
board.bin file and not for something like board-bus-device.bin like it does
for pre-cal data.
Due to this we have no way of providing correct BDF-s on the fly, so lets
extend the ath10k driver to first look for BDF-s in the
board-bus-device.bin format, for example: board-ahb-a800000.wifi.bin
If that fails, look for the default board file name as defined previously.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211009221711.2315352-1-robimarko@gmail.com
checkpatch warns:
drivers/net/wireless/ath/ath10k/mac.c:2696: line length of 92 exceeds 90 columns
drivers/net/wireless/ath/ath10k/mac.c:6942: line length of 94 exceeds 90 columns
drivers/net/wireless/ath/ath10k/mac.c:6948: line length of 91 exceeds 90 columns
These were introduced by commit 046d2e7c50 ("mac80211: prepare sta handling
for MLO support").
Compile tested only.
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220503060415.24499-2-kvalo@kernel.org
checkpatch warns:
drivers/net/wireless/ath/ath11k/mac.c:7760: line length of 91 exceeds 90 columns
This was introduced by commit 046d2e7c50 ("mac80211: prepare sta handling for
MLO support").
Compile tested only.
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220503060415.24499-1-kvalo@kernel.org
Add the support to attach WCN6750 and map iommu domain
for targets which do not have the support of TrustZone.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00573-QCAMSLSWPLZ-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220328062032.28881-1-quic_mpubbise@quicinc.com
First set of patches for v5.19 and this is a big one. We have two new
drivers, a change in mac80211 STA API affecting most drivers and
ath11k getting support for WCN6750. And as usual lots of fixes and
cleanups all over.
Major changes:
new drivers
* wfx: silicon labs devices
* plfxlc: pureLiFi X, XL, XC devices
mac80211
* host based BSS color collision detection
* prepare sta handling for IEEE 802.11be Multi-Link Operation (MLO) support
rtw88
* support TP-Link T2E devices
rtw89
* support firmware crash simulation
* preparation for 8852ce hardware support
ath11k
* Wake-on-WLAN support for QCA6390 and WCN6855
* device recovery (firmware restart) support for QCA6390 and WCN6855
* support setting Specific Absorption Rate (SAR) for WCN6855
* read country code from SMBIOS for WCN6855/QCA6390
* support for WCN6750
wcn36xx
* support for transmit rate reporting to user space
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEiBjanGPFTz4PRfLobhckVSbrbZsFAmJxS2sRHGt2YWxvQGtl
cm5lbC5vcmcACgkQbhckVSbrbZuNgwf9H2oxMKLKrlFoX1qHtNBwZuHS6IERhOkM
NI9DjS4MCyiUSbA5r3sWlpqXQeKIbG/05gUZ6Y0ircGFwnAGjZ6isPwo8pKFgbh5
QljXQjUTHbkshrXW8K+VGJxw4F1oiPlOGUDVdXPy2FLx5ZvBlaUV2rWQUzsWX9I0
EnrM6ygHBVejVYDe+JSkb1gzb/07xuZN410IJPuZTPKJfYiE0oGU3zpTbExFitaz
ObjfFUWqHrVue525WFAJ9Dbk8kYEKyMThr7rkkWekYJjujJLJo0qhEiZVZu0eEsk
Vq4PdKmQAqlgbShQ/3Mv8BRsSH2wy62+zKjPWL+8t4Gmm9DbLu+++A==
=T7Ii
-----END PGP SIGNATURE-----
Merge tag 'wireless-next-2022-05-03' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Kalle Valo says:
====================
wireless-next patches for v5.19
First set of patches for v5.19 and this is a big one. We have two new
drivers, a change in mac80211 STA API affecting most drivers and
ath11k getting support for WCN6750. And as usual lots of fixes and
cleanups all over.
Major changes:
new drivers
- wfx: silicon labs devices
- plfxlc: pureLiFi X, XL, XC devices
mac80211
- host based BSS color collision detection
- prepare sta handling for IEEE 802.11be Multi-Link Operation (MLO) support
rtw88
- support TP-Link T2E devices
rtw89
- support firmware crash simulation
- preparation for 8852ce hardware support
ath11k
- Wake-on-WLAN support for QCA6390 and WCN6855
- device recovery (firmware restart) support for QCA6390 and WCN6855
- support setting Specific Absorption Rate (SAR) for WCN6855
- read country code from SMBIOS for WCN6855/QCA6390
- support for WCN6750
wcn36xx
- support for transmit rate reporting to user space
* tag 'wireless-next-2022-05-03' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (228 commits)
rtw89: 8852c: rfk: add DPK
rtw89: 8852c: rfk: add IQK
rtw89: 8852c: rfk: add RX DCK
rtw89: 8852c: rfk: add RCK
rtw89: 8852c: rfk: add TSSI
rtw89: 8852c: rfk: add LCK
rtw89: 8852c: rfk: add DACK
rtw89: 8852c: rfk: add RFK tables
plfxlc: fix le16_to_cpu warning for beacon_interval
rtw88: remove a copy of the NAPI_POLL_WEIGHT define
carl9170: tx: fix an incorrect use of list iterator
wil6210: use NAPI_POLL_WEIGHT for napi budget
ath10k: remove a copy of the NAPI_POLL_WEIGHT define
ath11k: Add support for WCN6750 device
ath11k: Datapath changes to support WCN6750
ath11k: HAL changes to support WCN6750
ath11k: Add QMI changes for WCN6750
ath11k: Fetch device information via QMI for WCN6750
ath11k: Add register access logic for WCN6750
ath11k: Add HW params for WCN6750
...
====================
Link: https://lore.kernel.org/r/20220503153622.C1671C385A4@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
ath.git patches for v5.19. Major changes:
ath11k
* support setting Specific Absorption Rate (SAR) for WCN6855
* read country code from SMBIOS for WCN6855/QCA6390
* support for WCN6750
If the previous list_for_each_entry_continue_rcu() don't exit early
(no goto hit inside the loop), the iterator 'cvif' after the loop
will be a bogus pointer to an invalid structure object containing
the HEAD (&ar->vif_list). As a result, the use of 'cvif' after that
will lead to a invalid memory access (i.e., 'cvif->id': the invalid
pointer dereference when return back to/after the callsite in the
carl9170_update_beacon()).
The original intention should have been to return the valid 'cvif'
when found in list, NULL otherwise. So just return NULL when no
entry found, to fix this bug.
Cc: stable@vger.kernel.org
Fixes: 1f1d9654e1 ("carl9170: refactor carl9170_update_beacon")
Signed-off-by: Xiaomeng Tong <xiam0nd.tong@gmail.com>
Acked-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220328122820.1004-1-xiam0nd.tong@gmail.com
The comment next to WIL6210_NAPI_BUDGET says "arbitrary".
If we're picking arbitrary values let's pick the recommended
default which is NAPI_POLL_WEIGHT.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220429174643.196994-4-kuba@kernel.org
Defining local versions of NAPI_POLL_WEIGHT with the same
values in the drivers just makes refactoring harder.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220429174643.196994-3-kuba@kernel.org
WCN6750 is non-DBS 2x2 11AX chipset. Unlike QCA6390 which is a
DBS (dual band simultaneous) solution (2 LMACs), WCN6750 has a
single LMAC supporting 2G, 5G and 6G bands but will operate only
on one band at any given point.
WCN6750 is a PCIe based solution, but it is attached to the WPSS
(Wireless Processor SubSystem) Q6 processor, hence it is enumerated
by the Q6 processor. It is registered to the APSS processor
(Application Processor SubSystem) as a platform device(AHB) and
remoteproc APIs are used to boot up or shutdown the device like
other AHB devices.
Also, Device information like BAR and it's size is not known to the
APSS processor as the chip is enumerated by WPSS Q6. These details
are fetched over QMI.
STA and AP modes are supported. Verified basic connectivity and ping
in both the modes.
An important point to note is that though WCN6750 is a PCIe device,
it cannot be attached to any other platform except on Qualcomm
Snapdragon SoCs due to the aforementioned reasons.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220429170502.20080-10-quic_mpubbise@quicinc.com
HAL RX descriptor for WCN6750 is same as QCN9074, this
means that the size of the HAL RX decriptor and the DP
APIs that WCN6750 requires to enable datapath should be
initialized with that of QCN9074's RX descriptor size
and the DP APIs respectively. There is one change wrt to
REO configuration though, REO configuration for WCN6750
follows WCN6855, therefore use reo_setup() of WCN6855
for WCN6750.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220429170502.20080-9-quic_mpubbise@quicinc.com
Add HAL changes required to support WCN6750. Offsets of some registers
for WCN6750 are different from other supported devices; move such
register offsets to platform specific ath11k_hw_regs.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220429170502.20080-8-quic_mpubbise@quicinc.com
In the case of WCN6750, FW doesn't request for DDR memory
via QMI, instead it uses a fixed 12MB reserved Memory region
in the DDR which is called as MSA region. As a result, QMI
message sequence is not same as other ath11k supported devices.
Also, M3 firmware will be bundled into the FW and will be
downloaded to the target as part of Q6 boot.
This is the QMI flow in the case of WCN6750,
1) QMI firmware indication REQ/RESP
2) QMI host capability REQ/RESP
3) QMI target capability REQ/RESP
4) QMI device info REQ/RESP
5) QMI BDF download
6) QMI FW ready
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220429170502.20080-7-quic_mpubbise@quicinc.com
Since WPPS Q6 does the PCIe enumeration of WCN6750, device
information like BAR and BAR size is not known to the APPS
processor (Application Processor SubSystem). In order to
fetch these details, a QMI message called device info request
will be sent to the target. Therefore, add logic to fetch
BAR details from the target.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220429170502.20080-6-quic_mpubbise@quicinc.com
WCN6750 uses static window mapping to access the HW registers.
Unlike QCN9074 which uses 3rd window for UMAC and 2nd window
for CE register access, WCN6750 uses 1st window for UMAC
and 2nd window for CE registers.
Also, refactor the code so that WCN6750 can use the existing
ath11k_pci_read32/write32() APIs for accessing the registers.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220429170502.20080-5-quic_mpubbise@quicinc.com
WCN6750 is a PCIe based solution that is attached to and enumerated
by the WPSS (Wireless Processor SubSystem) Q6 processor.
Though it is a PCIe device, since it is not attached to APSS processor
(Application Processor SubSystem), APSS will be unaware of such a decice
and hence it is registered to the APSS processor as a platform device(AHB).
Because of this hybrid nature, it is called as a hybrid bus device.
A new variable hybrid_bus_type is defined in hw_params to indicate the
hybrid nature of the device.
Add HW params for WCN6750.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220429170502.20080-4-quic_mpubbise@quicinc.com
In ath11k, bus_params were added with an intention to hold
parameters related to bus (AHB/PCI), but this is not true
as some bus parameters being different between chipsets of
the same bus.
With the addition of WCN6750 to ath11k, bus parameters are
going to be entirely different among AHB devices. Therefore,
it is wise to move bus_params to hw_params and get rid of
bus_params entirely.
Also, mhi_support parameter is not used anywhere in the driver,
remove it from bus_params.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220429170502.20080-3-quic_mpubbise@quicinc.com
In the phase of wlan load, it has hw scan and 11d scan which sent to
firmware by ath11k, then hw scan and 11d scan will use about 14 seconds,
and meanwhile ath11k_reg_update_chan_list() is running in workqueue of
ath11k_base, and wait for 11d scan/hw scan finished. When the hw scan
finished, mac80211 will start to connect and send management packet,
at this moment, ath11k_reg_update_chan_list() is still waiting for 11d
scan finished, so wmi_mgmt_tx_work of ath11k will not run and thus the
tx management packet also not send out and lead authentication timed
out.
log:
INFO kernel: [ 187.885322] wlan0: authenticate with 72:6c:57:43:9f:90
INFO kernel: [ 187.937266] wlan0: send auth to 72:6c:57:43:9f:90 (try 1/3)
INFO kernel: [ 188.626944] wlan0: send auth to 72:6c:57:43:9f:90 (try 2/3)
INFO kernel: [ 189.650999] wlan0: send auth to 72:6c:57:43:9f:90 (try 3/3)
INFO kernel: [ 190.651917] wlan0: authentication with 72:6c:57:43:9f:90 timed out
Change wmi_mgmt_tx_work to another queue workqueue_aux of ath11k_base,
then connection success.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220428023320.4007-1-quic_wgong@quicinc.com
When test connect/disconnect to an AP frequently with WCN6855, sometimes
it show below log.
[ 277.040121] wls1: deauthenticating from 8c:21:0a:b3:5a:64 by local choice (Reason: 3=DEAUTH_LEAVING)
[ 277.050906] ath11k_pci 0000:05:00.0: wmi stats vdev id 0 mac 00:03:7f:29:61:11
[ 277.050944] ath11k_pci 0000:05:00.0: wmi stats bssid 8c:21:0a:b3:5a:64 vif pK-error
[ 277.050954] ath11k_pci 0000:05:00.0: not found station for bssid 8c:21:0a:b3:5a:64
[ 277.050961] ath11k_pci 0000:05:00.0: failed to parse rssi chain -71
[ 277.050967] ath11k_pci 0000:05:00.0: failed to pull fw stats: -71
[ 277.050976] ath11k_pci 0000:05:00.0: wmi stats vdev id 0 mac 00:03:7f:29:61:11
[ 277.050983] ath11k_pci 0000:05:00.0: wmi stats bssid 8c:21:0a:b3:5a:64 vif pK-error
[ 277.050989] ath11k_pci 0000:05:00.0: not found station for bssid 8c:21:0a:b3:5a:64
[ 277.050995] ath11k_pci 0000:05:00.0: failed to parse rssi chain -71
[ 277.051000] ath11k_pci 0000:05:00.0: failed to pull fw stats: -71
[ 278.064050] ath11k_pci 0000:05:00.0: failed to request fw stats: -110
Reason is:
When running disconnect operation, sta_info removed from local->sta_hash
by __sta_info_destroy_part1() from __sta_info_flush(), after this,
ieee80211_find_sta_by_ifaddr() which called by
ath11k_wmi_tlv_fw_stats_data_parse() and ath11k_wmi_tlv_rssi_chain_parse()
cannot find this station, then failed log printed.
steps are like this:
1. when disconnect from AP, __sta_info_destroy() called __sta_info_destroy_part1()
and __sta_info_destroy_part2().
2. in __sta_info_destroy_part1(), it has "sta_info_hash_del(local, sta)"
and "list_del_rcu(&sta->list)", it will remove the ieee80211_sta from the
list of ieee80211_hw.
3. in __sta_info_destroy_part2(), it called drv_sta_state()->ath11k_mac_op_sta_state(),
then peer->sta is clear at this moment.
4. in __sta_info_destroy_part2(), it then called sta_set_sinfo()->drv_sta_statistics()
->ath11k_mac_op_sta_statistics(), then WMI_REQUEST_STATS_CMDID sent to firmware.
5. WMI_UPDATE_STATS_EVENTID reported from firmware, at this moment, the
ieee80211_sta can not be found again because it has remove from list in
step2 and also peer->sta is clear in step3.
6. in __sta_info_destroy_part2(), it then called cleanup_single_sta()->
sta_info_free()->kfree(sta), at this moment, the ieee80211_sta is freed
in memory, then the failed log will not happen because function
ath11k_mac_op_sta_state() will not be called.
Actually this print log is not a real error, it is only to skip parse the
info, so change to skip print by default debug setting.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220428022426.2927-1-quic_wgong@quicinc.com
Double free crash is observed when FW recovery(caused by wmi
timeout/crash) is followed by immediate suspend event. The FW recovery
is triggered by ath10k_core_restart() which calls driver clean up via
ath10k_halt(). When the suspend event occurs between the FW recovery,
the restart worker thread is put into frozen state until suspend completes.
The suspend event triggers ath10k_stop() which again triggers ath10k_halt()
The double invocation of ath10k_halt() causes ath10k_htt_rx_free() to be
called twice(Note: ath10k_htt_rx_alloc was not called by restart worker
thread because of its frozen state), causing the crash.
To fix this, during the suspend flow, skip call to ath10k_halt() in
ath10k_stop() when the current driver state is ATH10K_STATE_RESTARTING.
Also, for driver state ATH10K_STATE_RESTARTING, call
ath10k_wait_for_suspend() in ath10k_stop(). This is because call to
ath10k_wait_for_suspend() is skipped later in
[ath10k_halt() > ath10k_core_stop()] for the driver state
ATH10K_STATE_RESTARTING.
The frozen restart worker thread will be cancelled during resume when the
device comes out of suspend.
Below is the crash stack for reference:
[ 428.469167] ------------[ cut here ]------------
[ 428.469180] kernel BUG at mm/slub.c:4150!
[ 428.469193] invalid opcode: 0000 [#1] PREEMPT SMP NOPTI
[ 428.469219] Workqueue: events_unbound async_run_entry_fn
[ 428.469230] RIP: 0010:kfree+0x319/0x31b
[ 428.469241] RSP: 0018:ffffa1fac015fc30 EFLAGS: 00010246
[ 428.469247] RAX: ffffedb10419d108 RBX: ffff8c05262b0000
[ 428.469252] RDX: ffff8c04a8c07000 RSI: 0000000000000000
[ 428.469256] RBP: ffffa1fac015fc78 R08: 0000000000000000
[ 428.469276] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 428.469285] Call Trace:
[ 428.469295] ? dma_free_attrs+0x5f/0x7d
[ 428.469320] ath10k_core_stop+0x5b/0x6f
[ 428.469336] ath10k_halt+0x126/0x177
[ 428.469352] ath10k_stop+0x41/0x7e
[ 428.469387] drv_stop+0x88/0x10e
[ 428.469410] __ieee80211_suspend+0x297/0x411
[ 428.469441] rdev_suspend+0x6e/0xd0
[ 428.469462] wiphy_suspend+0xb1/0x105
[ 428.469483] ? name_show+0x2d/0x2d
[ 428.469490] dpm_run_callback+0x8c/0x126
[ 428.469511] ? name_show+0x2d/0x2d
[ 428.469517] __device_suspend+0x2e7/0x41b
[ 428.469523] async_suspend+0x1f/0x93
[ 428.469529] async_run_entry_fn+0x3d/0xd1
[ 428.469535] process_one_work+0x1b1/0x329
[ 428.469541] worker_thread+0x213/0x372
[ 428.469547] kthread+0x150/0x15f
[ 428.469552] ? pr_cont_work+0x58/0x58
[ 428.469558] ? kthread_blkcg+0x31/0x31
Tested-on: QCA6174 hw3.2 PCI WLAN.RM.4.4.1-00288-QCARMSWPZ-1
Co-developed-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Abhishek Kumar <kuabhs@chromium.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220426221859.v2.1.I650b809482e1af8d0156ed88b5dc2677a0711d46@changeid
This read the country code from SMBIOS and send the country code
to firmware, firmware will indicate the regulatory domain info of the
country code and then ath11k will use the info.
dmesg:
[ 1242.637173] ath11k_pci 0000:02:00.0: chip_id 0x2 chip_family 0xb board_id 0xff soc_id 0x400c0200
[ 1242.637176] ath11k_pci 0000:02:00.0: fw_version 0x110b09e5 fw_build_timestamp 2021-06-22 09:32 fw_build_id QC_IMAGE_VERSION_STRING=WLAN.HSP.1.1-02533-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
[ 1242.637253] ath11k_pci 0000:02:00.0: worldwide regdomain setting from SMBIOS
[ 1242.637259] ath11k_pci 0000:02:00.0: bdf variant name not found.
[ 1242.637261] ath11k_pci 0000:02:00.0: SMBIOS bdf variant name not set.
[ 1242.637263] ath11k_pci 0000:02:00.0: DT bdf variant name not set.
[ 1242.927543] ath11k_pci 0000:02:00.0: set current country pdev id 0 alpha2 00
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220421023501.32167-1-quic_wgong@quicinc.com
Currently, WBM idle ring HP is updated much before the shadow
configuration is sent to the FW. Any update to the shadow
registers before FW mode on request would not be reflected
on to the actual HW registers failing to bring up the device.
Send FW mode ON QMI request before WBM idle ring HP update
to fix this problem.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00573-QCAMSLSWPLZ-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220406094107.17878-12-quic_mpubbise@quicinc.com
WCN6750 is a single PDEV non-DBS chip which supports 2G, 5G and 6G bands.
It is a single LMAC device which can be either hooked to 2G/5G/6G bands.
Add WMI changes to support WCN6750.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00573-QCAMSLSWPLZ-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220406094107.17878-11-quic_mpubbise@quicinc.com
Though WCN6750 is a single PDEV device, it is not a
DBS solution. So, do not put HW in DBS mode for WCN6750.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00573-QCAMSLSWPLZ-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220406094107.17878-10-quic_mpubbise@quicinc.com
This patch fixes an invalid TX PA DC bias level on QCA9561, which
results in a very low output power and very low throughput as devices
are further away from the AP (compared to other 2.4GHz APs).
This patch was suggested by Felix Fietkau, who noted[1]:
"The value written to that register is wrong, because while the mask
definition AR_CH0_TOP2_XPABIASLVL uses a different value for 9561, the
shift definition AR_CH0_TOP2_XPABIASLVL_S is hardcoded to 12, which is
wrong for 9561."
In real life testing, without this patch the 2.4GHz throughput on
Yuncore XD3200 is around 10Mbps sitting next to the AP, and closer to
practical maximum with the patch applied.
[1] https://lore.kernel.org/all/91c58969-c60e-2f41-00ac-737786d435ae@nbd.name
Signed-off-by: Thibaut VARÈNE <hacks+kernel@slashdirt.org>
Acked-by: Felix Fietkau <nbd@nbd.name>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220417145145.1847-1-hacks+kernel@slashdirt.org
The "rxstatus->rs_keyix" eventually gets passed to test_bit() so we need to
ensure that it is within the bitmap.
drivers/net/wireless/ath/ath9k/common.c:46 ath9k_cmn_rx_accept()
error: passing untrusted data 'rx_stats->rs_keyix' to 'test_bit()'
Fixes: 4ed1a8d4a2 ("ath9k_htc: use ath9k_cmn_rx_accept")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220409061225.GA5447@kili
Using pm_runtime_resume_and_get() is more appropriate
for simplifing code.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220411013602.2517086-1-chi.minghao@zte.com.cn
drivers/net/wireless/ath/ath11k/mac.c:8175:13: error: ‘ath11k_mac_op_ipv6_changed’ defined but not used [-Werror=unused-function]
static void ath11k_mac_op_ipv6_changed(struct ieee80211_hw *hw,
^~~~~~~~~~~~~~~~~~~~~~~~~~
Wrap it with #ifdef block to fix this.
Fixes: c3c36bfe99 ("ath11k: support ARP and NS offload")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220411020843.10284-1-yuehaibing@huawei.com
Add the missing unlock before return from function ath11k_wow_op_resume()
in the error handling case.
Fixes: 90bf5c8d0f ("ath11k: purge rx pktlog when entering WoW")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220408030912.3087293-1-yangyingliang@huawei.com
