Currently ath11k does not send the country code to firmware after device
recovery, as a result the regdomain info is reported from firmware by
default. Regdomain info is important, so ath11k also need to restore
it to the value which was used before recovery.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220324011856.11014-1-quic_wgong@quicinc.com
When more clients (128) are connected, the UL data traffic
KPI measurement is low compared to single client. This issue
is due to more CPU cycles spent on the peer lookup operation
with more clients. So reduce the peer lookup operation by
modifying the linear based lookup operation into the rhash
based lookup operation. This improve the peak throughput
measurement. Since this is a software algorithm change, it is
applicable for all the platforms.
TCP UL 128 Clients test case Observation (64bit system):
Previous: ~550 Mbps
Now : ~860 Mbps
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01067-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1644036628-5334-1-git-send-email-quic_periyasa@quicinc.com
This is to read variant from SMBIOS such as read from DT, the variant
string will be used to one part of string which used to search board
data from board-2.bin.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220315104721.26649-3-quic_wgong@quicinc.com
In Qualcomm ARM platforms there is WL_EN pin and other power regulators
which can be controlled at platform side to completely reset the chip.
For most of x86 and other platforms, the chip is connected via PCIe M.2
interface, and there is no way to control WL_EN pin. Instead the host
driver needs to reset the chip via PCIE_SOC_GLOBAL_RESET hardware
register, just like ath11k does currently.
But when using PCIE_SOC_GLOBAL_RESET there are some hardware registers
which are not cleared/restored. To handle those cases we can enable
PLATFORM_CAP_PCIE_GLOBAL_RESET QMI host capability to tell the firmware
to do some platform specific operations after firmware download.
This does not fix any known issues, but is recommended by the firmware
team, so enable the capability on QCA6390 and WCN6855 PCI devices. It is
currently unclear if this should be enabled also on QCN9074, so leave it
disabled for now. On AHB devices this is not needed as they don't use
PCIE_SOC_GLOBAL_RESET.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Baochen Qiang <bqiang@codeaurora.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211011055602.77342-1-bqiang@codeaurora.org
Add hw-restart to directly restart wlan. Like UTF mode start it will
restart hardware and download firmware again.
Usage:
1. Run command:
echo hw-restart > /sys/kernel/debug/ath11k/qca6390\ hw2.0/simulate_fw_crash
echo hw-restart > /sys/kernel/debug/ath11k/wcn6855\ hw2.0/simulate_fw_crash
2. wlan will be restart and do recovery process and success.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03003-QCAHSPSWPL_V1_V2_SILICONZ_LITE-2
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220228064606.8981-4-quic_wgong@quicinc.com
ieee80211_reconfig() of mac80211 is the main function for recovery of
each ieee80211_hw and ath11k, and ath11k_core_reconfigure_on_crash()
is the main function for recovery of ath11k_base, it has more than
one ieee80211_hw and ath11k for each ath11k_base, so it need to add
synchronization between them, otherwise it has many issue.
For example, when ath11k_core_reconfigure_on_crash() is not complete,
mac80211 send a hw scan request to ath11k, it leads firmware crash,
because firmware has not been initialized at that moment, firmware
is only finished downloaded and loaded, it can not receive scan
command.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03003-QCAHSPSWPL_V1_V2_SILICONZ_LITE-2
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220228064606.8981-3-quic_wgong@quicinc.com
Currently ath11k has device recovery logic, it is introduced by this
patch "ath11k: Add support for subsystem recovery" which is upstream
by https://git.kernel.org/pub/scm/linux/kernel/git/kvalo/ath.git/commit/?h=ath11k-bringup&id=3a7b4838b6f6f234239f263ef3dc02e612a083ad.
The patch is for AHB devices such as IPQ8074, it has remote proc module
which is used to download the firmware and boots the processor which
firmware is running on. If firmware crashed, remote proc module will
detect it and download and boot firmware again. Below command will
trigger a firmware crash, and then user can test feature of device
recovery.
Test command:
echo assert > /sys/kernel/debug/ath11k/qca6390\ hw2.0/simulate_fw_crash
echo assert > /sys/kernel/debug/ath11k/wcn6855\ hw2.0/simulate_fw_crash
Unfortunately, QCA6390 is PCIe bus, it does not have the remote proc
module, it use mhi module to communicate between firmware and ath11k.
So ath11k does not support device recovery for QCA6390 currently.
This patch is to add the extra logic which is different for QCA6390.
When firmware crashed, MHI_CB_EE_RDDM event will be indicate by
firmware and then ath11k_mhi_op_status_cb which is the callback of
mhi_controller will receive the MHI_CB_EE_RDDM event, then ath11k
will start to do recovery process, ath11k_core_reset() calls
ath11k_hif_power_down()/ath11k_hif_power_up(), then the mhi/ath11k
will start to download and boot firmware. There are some logic to
avoid deadloop recovery and two simultaneous recovery operations.
And because it has muti-radios for the soc, so it add some logic
in ath11k_mac_op_reconfig_complete() to make sure all radios has
reconfig complete and then complete the device recovery.
Also it add workqueue_aux, because ab->workqueue is used when receive
ATH11K_QMI_EVENT_FW_READY in recovery process(queue_work(ab->workqueue,
&ab->restart_work)), and ath11k_core_reset will wait for max
ATH11K_RESET_TIMEOUT_HZ for the previous restart_work finished, if
ath11k_core_reset also queued in ab->workqueue, then it will delay
restart_work of previous recovery and lead previous recovery fail.
ath11k recovery success for QCA6390/WCN6855 after apply this patch.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03003-QCAHSPSWPL_V1_V2_SILICONZ_LITE-2
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220228064606.8981-2-quic_wgong@quicinc.com
Currently it does not have regdb files for QCA6390, so disable its regdb
support feature now.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-05266-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220319023543.14288-3-quic_wgong@quicinc.com
Currently ATH11K_BD_IE_BOARD_EXT is not used, so remove it.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220319023543.14288-2-quic_wgong@quicinc.com
ath11k_peer_find_by_addr states via lockdep that ab->base_lock must be
held when calling that function in order to protect the list. All
callers except ath11k_mac_op_unassign_vif_chanctx have that lock
acquired when calling ath11k_peer_find_by_addr. That lock is also not
transitively held by a path towards ath11k_mac_op_unassign_vif_chanctx.
The solution is to acquire the lock when calling
ath11k_peer_find_by_addr inside ath11k_mac_op_unassign_vif_chanctx.
I am currently working on a static analyser to detect missing locks and
this was a reported case. I manually verified the report by looking at
the code, but I do not have real hardware so this is compile tested
only.
Fixes: 701e48a43e ("ath11k: add packet log support for QCA6390")
Signed-off-by: Niels Dossche <dossche.niels@gmail.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220314215253.92658-1-dossche.niels@gmail.com
Currently fw build id is printed during init as follows.
fw_version 0x250684a5 fw_build_timestamp 2021-07-13 10:57
fw_build_id QC_IMAGE_VERSION_STRING=WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
The string "QC_IMAGE_VERSION_STRING=" is removed from the log
to improve readability.
With this patch the fw build id is printed during init as follows.
fw_version 0x250684a5 fw_build_timestamp 2021-07-13 10:57
fw_build_id WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Signed-off-by: Hari Chandrakanthan <quic_haric@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1646825065-7736-1-git-send-email-quic_haric@quicinc.com
Introduce new helper function for peer delete to reuse this logic
in all peer cleanup procedures. Found this in code review.
Also this change is applicable for all the platform.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01067-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1646024079-26391-1-git-send-email-quic_periyasa@quicinc.com
Host sets GTK related info to firmware before WoW is enabled, and
gets rekey replay_count and then disables GTK rekey when WoW quits.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <quic_cjhuang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1644308006-22784-7-git-send-email-quic_cjhuang@quicinc.com
Support ARP and NS offload in WoW state.
Tested this way: put machine A with QCA6390 to WoW state,
ping/ping6 machine A from another machine B, check sniffer to see
any ARP response and Neighbour advertisement from machine A.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <quic_cjhuang@quicinc.com>
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1644308006-22784-6-git-send-email-quic_cjhuang@quicinc.com
This change is to purge rx pktlog when entering WoW and reap
the mon_status buffer to keep it empty. When leaving WoW, host
restarts the reap timer. In WoW state, it's not allowed to feed
into mon_status rings per firmware team's recommendation.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <quic_cjhuang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1644308006-22784-5-git-send-email-quic_cjhuang@quicinc.com
Host needs to set hardware data filter before entering WoW to
let firmware drop needless broadcast/mulitcast frames to avoid
frequent wakeup. Host clears hardware data filter when leaving WoW.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <quic_cjhuang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1644308006-22784-4-git-send-email-quic_cjhuang@quicinc.com
Implement net-detect feature by setting flag
WIPHY_WOWLAN_NET_DETECT if firmware supports this
feature. Driver sets the related PNO configuration
to firmware before entering WoW and firmware then
scans periodically and wakes up host if a specific
SSID is found.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <quic_cjhuang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1644308006-22784-3-git-send-email-quic_cjhuang@quicinc.com
Implement basic WoW functionalities such as magic-packet, disconnect
and pattern. The logic is very similar to ath10k.
When WoW is configured, ath11k_core_suspend and ath11k_core_resume
are skipped as WoW configuration and hif suspend/resume are done in
ath11k_wow_op_suspend() and ath11k_wow_op_resume().
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <quic_cjhuang@quicinc.com>
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1644308006-22784-2-git-send-email-quic_cjhuang@quicinc.com
All work currently pending will be done first by calling destroy_workqueue,
so there is no need to flush it explicitly.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Lv Ruyi (CGEL ZTE) <lv.ruyi@zte.com.cn>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220301013246.2052570-1-lv.ruyi@zte.com.cn
ath.git patches for v5.18. Major changes:
ath11k
* debugfs interface to configure firmware debug log level
* debugfs interface to test Target Wake Time (TWT)
* provide 802.11ax High Efficiency (HE) data via radiotap
ath9k
* use hw_random API instead of directly dumping into random.c
wcn36xx
* fix wcn3660 to work on 5 GHz band
Target copies spectral report and CFR report through dbring to
host for further processing. This mechanism involves ring and
buffer management in the Host, FW, and uCode, where improper
tail pointer update issues are seen.
This dbring debug support help to debug such issues by tracking
head and tail pointer movement along with the timestamp at which
each buffer is received and replenished.
Provide a debugfs interface to enalbe/disable dbring debug
support and dump the dbring debug entries.
Also introduced a new hardware param to add dbring debugfs support
for few hardwares which are using dbings.
Usage:
echo <dbr_id> <val> > /sys/kernel/debug/ath11k/ipq8074_2/
mac0/enable_dbr_debug
dbr_id: 0 for spectral and 1 for CFR
val: 0 - disable, 1 - enable.
Tested-on: IPQ8074 WLAN.HK.2.4.0.1-01467-QCAHKSWPL_SILICONZ-1
Signed-off-by: Venkateswara Naralasetty <quic_vnaralas@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1645366059-11798-1-git-send-email-quic_vnaralas@quicinc.com
Translate HE status to radiotap format. This uses HE radiotap
definitions from include/net/ieee80211_radiotap.h.
Co-developed-by: Miles Hu <milehu@codeaurora.org>
Signed-off-by: Miles Hu <milehu@codeaurora.org>
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220217012112.31211-4-pradeepc@codeaurora.org
Add new bitmasks and macro definitions required for parsing HE
status tlvs. Decode HE status tlvs, which will used in dumping
ppdu stats as well as updating radiotap headers.
Co-developed-by: Miles Hu <milehu@codeaurora.org>
Signed-off-by: Miles Hu <milehu@codeaurora.org>
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220217012112.31211-3-pradeepc@codeaurora.org
This allows us to pass HE rates down into the stack.
Co-developed-by: Miles Hu <milehu@codeaurora.org>
Signed-off-by: Miles Hu <milehu@codeaurora.org>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220217012112.31211-2-pradeepc@codeaurora.org
In some scenarios like firmware crashes during init time
and hardware gets restarted after qmi firmware ready event.
During restart, ath11k_core_qmi_firmware_ready() returns timeout.
But, this failure is not handled and ATH11K_FLAG_REGISTERED is set.
When hardware restart completed, firmware sends firmware ready event
again. Since ATH11K_FLAG_REGISTERED is already set, ath11k handles
this as core restart. Inits are not done because of previous timeout.
But ath11k_core_restart does deinit's which causes NULL pointer crash.
Fix this by handling failure from ath11k_core_qmi_firmware_ready().
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.7.0.1-00881-QCAHKSWPL_SILICONZ-1
Signed-off-by: Seevalamuthu Mariappan <quic_seevalam@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1645079195-13564-1-git-send-email-quic_seevalam@quicinc.com
REO2SW ring descriptor is currently allocated in cacheable memory.
While reaping reo ring entries on second trial after updating head
pointer, first entry is not invalidated before accessing it.
This results in host reaping and using cached descriptor which is
already overwritten in memory by DMA device (HW).
Since the contents of descriptor(buffer id, peer info and other information
bits) are outdated host throws errors like below while parsing corresponding
MSDU's and drops them.
[347712.048904] ath11k_pci 0004:01:00.0: msdu_done bit in attention is not set
[349173.355503] ath11k_pci 0004:01:00.0: frame rx with invalid buf_id 962
Move the try_again: label above ath11k_hal_srng_access_begin()
so that first entry will be invalidated and prefetched.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Fixes: 6452f0a3d5 ("ath11k: allocate dst ring descriptors from cacheable memory")
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1645000354-32558-1-git-send-email-quic_ramess@quicinc.com
The rddm_size is needed by firmware while mhi enter RDDM state, add it
to support recovery when ath11k receive MHI_CB_EE_RDDM message.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03003-QCAHSPSWPL_V1_V2_SILICONZ_LITE-2
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220209060012.32478-4-quic_wgong@quicinc.com
This is to fix m3 buffer reuse issue as m3_mem->size isn't set to
ZERO in free function, which leads invalid m3 downloading to
firmware and firmware crashed.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03003-QCAHSPSWPL_V1_V2_SILICONZ_LITE-2
Signed-off-by: Carl Huang <quic_cjhuang@quicinc.com>
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220209060012.32478-3-quic_wgong@quicinc.com
ath11k_qmi_free_target_mem_chunk() and ath11k_qmi_m3_free() is static
in qmi.c, they are needed for recovery, export them in a new function.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03003-QCAHSPSWPL_V1_V2_SILICONZ_LITE-2
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220209060012.32478-2-quic_wgong@quicinc.com
We add the fields for parsing extended ADDBA request/respond,
and new max 1K aggregation for limit ADDBA request/respond.
Adjust drivers to use the proper macro, IEEE80211_MAX_AMPDU_BUF ->
IEEE80211_MAX_AMPDU_BUF_HE.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Link: https://lore.kernel.org/r/20220214173004.b8b447ce95b7.I0ee2554c94e89abc7a752b0f7cc7fd79c273efea@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
More than 20000 PPDU id jumping causing status ring and destination
ring processing not sync. The status ring is processed and the
destination ring is not processed. Since destination is not reaped for
so long, backpressure occurs at the destination ring.
To address this issue update the PPDU id with the latest PPDU, this
will allow the destination ring to be reaped and will prevent the
rings from getting out of sync.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1.r1-00026-QCAHKSWPL_SILICONZ-2
Signed-off-by: Karthikeyan Kathirvel <quic_kathirve@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220210064706.6171-1-quic_kathirve@quicinc.com
Radar detection fails in the secondary 80 MHz when the
the AP's primary 80 MHz is in non-DFS region in 160 MHz.
This is due to WMI channel flag WMI_CHAN_INFO_DFS_FREQ2 is not set
properly in case of the primary 80 MHz is in non-DFS region.
HALPHY detects the radar pulses in the secondary 80 MHz only when
WMI_CHAN_INFO_DFS_FREQ2 is set.
Fix this issue by setting WMI channel flag WMI_CHAN_INFO_DFS_FREQ2
based on the radar_enabled flag from the channel context.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Signed-off-by: Venkateswara Naralasetty <quic_vnaralas@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1644416019-820-2-git-send-email-quic_vnaralas@quicinc.com
Fix WARN_ON() from ath11k_mac_update_vif_chan() if vdev is not up.
Since change_chanctx can be called even before vdev_up from
ieee80211_start_ap->ieee80211_vif_use_channel->
ieee80211_recalc_radar_chanctx.
Do vdev stop followed by a vdev start in case of vdev is down.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Signed-off-by: Venkateswara Naralasetty <quic_vnaralas@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1644416019-820-1-git-send-email-quic_vnaralas@quicinc.com
The rate_idx which passed to ath11k_debugfs_sta_add_tx_stats() by
ath11k_dp_tx_update_txcompl() is not initialized, add initialization
for it.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03003-QCAHSPSWPL_V1_V2_SILICONZ_LITE-2
Fixes: 1b8bb94c06 ("ath11k: report tx bitrate for iw wlan station dump")
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220209060816.423-1-quic_wgong@quicinc.com
The size of the status_driver_data field was not adjusted when
the is_valid_ack_signal field was added.
Since the size of struct ieee80211_tx_info is limited, replace
the is_valid_ack_signal field with a flags field, and adjust the
struct size accordingly.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20220202104617.0ff363d4fa56.I45792c0187034a6d0e1c99a7db741996ef7caba3@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
These calls are used for debugging and will be required for WFA
certification tests.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-01179-QCAHKSWPL_SILICONZ-1
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Aloka Dixit <alokad@codeaurora.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220131031043.1295-1-alokad@codeaurora.org
Add debugfs interface "fw_dbglog_config" to configure firmware log level.
Configuration is done via WMI command WMI_DBGLOG_CFG_CMDID.
Command to configure,
echo "<dbglog_param> <values>" >
/sys/kernel/debug/ath11k/<hw>/macX/fw_dbglog_config
where dbglog_param can be,
1) WMI_DEBUG_LOG_PARAM_LOG_LEVEL - configure log level for a given module
here, <values> = <0xaaaa00bb>, 'aaaa' - module id and 'bb' - loglevel
2) WMI_DEBUG_LOG_PARAM_VDEV_ENABLE - enable debug log for a given vdev
here, <values> = vdev_id
3) WMI_DEBUG_LOG_PARAM_VDEV_DISABLE - disable debug log for a given vdev
except ERROR logs
here, <values> = vdev_id
4) WMI_DEBUG_LOG_PARAM_VDEV_ENABLE_BITMAP - set vdev enable bitmap
here, <values> = vdev_enable_bitmap
5) WMI_DEBUG_LOG_PARAM_MOD_ENABLE_BITMAP - set a given log level to all the
modules specified in the module bitmap. Command to configure for this log param,
$ echo "5 <values> <module_id_index> <is_end>" >
/sys/kernel/debug/ath11k/<hw>/macX/fw_dbglog_config
here,
<values> = <0xaaaaaaaa000000bb>, 'aaaaaaaa' - module bitmap and
'bb' - loglevel
<module_id_index> = index of module bitmap. Max module id is 512.
So, module_id_index is 0-15.
<is_end> = to indicate if more configuration to follow.
6) WMI_DEBUG_LOG_PARAM_WOW_MOD_ENABLE_BITMAP - Wow mode specific logging enable.
Command to configure for this log param,
$ echo "6 <values> <module_id_index> <is_end>" >
/sys/kernel/debug/ath11k/<hw>/macX/fw_dbglog_config
here,
<values> = <0xaaaaaaaa000000bb>, 'aaaaaaaa' - module bitmap and
'bb' - loglevel
<module_id_index> = index of module bitmap. Max module id is 512.
So, module_id_index is 0-15.
<is_end> = to indicate if more configuration to follow.
Sample command usage,
To enable module WLAN_MODULE_WMI and log level ATH11K_FW_DBGLOG_VERBOSE,
echo "1 0x10001" > /sys/kernel/debug/ath11k/<hw>/macX/fw_dbglog_config
To enable module bit map from 32 to 63 and log level ATH11K_FW_DBGLOG_VERBOSE,
echo "5 0xffffffff00000001 1 1" > /sys/kernel/debug/ath11k/<hw>/macX/fw_dbglog_config
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1-01734-QCAHKSWPL_SILICONZ-1
Signed-off-by: Seevalamuthu Mariappan <quic_seevalam@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1642405103-32302-1-git-send-email-quic_seevalam@quicinc.com
