The design of INT indicator register (R_AX_PCIE_HIMR00_V1) is to reduce IO
during frequent interrupts, because it can stop chip sending interrupt to
host if we just set this indicator to 0, not all IMR(s). This indicator
register looks like a root interrupt controller of wifi chip.
However, we can't set all other IMR(s) to 0 during we are running on
interrupt service routine, or the indicator register can't reflect the
status of certain interrupt happened during this period, and then miss
some interrupts especially SER interrupt events.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220516005215.5878-7-pkshih@realtek.com
Before 6 GHz band was supported, i.e. only 2 GHz and 5 GHz, they were the
same from the numerical point of view. However, after 6 GHz band support,
we need to do this conversion logically.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220516005215.5878-6-pkshih@realtek.com
Update notes:
update the following to HALRF_027_00_052
TX power by rate table
TX power limit table
TX power limit RU table
TX shape table doesn't seem to be changed on HALRF_027_00_052
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220516005215.5878-5-pkshih@realtek.com
To make user space can set TX antenna via iw command. Then, we can diagnose
antenna is connected properly or not, and measure TX power in single path.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220516005215.5878-3-pkshih@realtek.com
When peer's NSS, rate or bandwidth is changed, we update RA(rate adaptive)
mask to ensure transmitting packets properly.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220516005215.5878-2-pkshih@realtek.com
BSSID CAM is a kind of CAM that is used to determine if we receive a packet
or not. Add an entry to assist in debugging.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220506120216.58567-6-pkshih@realtek.com
EDCCA signal can block transmitting in certain situation, so ignore this
signal and use others to decide transmitting time.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220506120216.58567-4-pkshih@realtek.com
Set proper setting according to RX quota, and then it doesn't break buffer
due to size of received packet exceeding buffer size.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220506120216.58567-3-pkshih@realtek.com
Modify NBI and PD boost settings according to different primary channels.
This setting can decrease the false alarm induced by DC.
Signed-off-by: Hsuan Hung <hsuan8331@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220506120216.58567-2-pkshih@realtek.com
This initial vesion is usable now. It can support STA, AP and monitor
modes, so we can add 8852ce to Kconfig and Makefile.
We are still working on some features, such as deep power save, and BT
coexistence. But, this version still can have a good WiFi-only performance
already, and will continue to fine tune power consumption.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220503120001.79272-9-pkshih@realtek.com
By experiments, it spends ~45/1090~2480us to enter/leave low power mode,
so the old polling interval 1000us can waste time. Use smaller polling
interval depends on experimental results to reduce the time to transition
state.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220503120001.79272-5-pkshih@realtek.com
The chip_info include BT coexistence tables, size and number of hardware
components, and supported functions.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220503120001.79272-4-pkshih@realtek.com
The commit 16b44ed0ff ("rtw89: add RF H2C to notify firmware") is to
add firmware command, and this commit is to prepare the channels. Then,
firmware can get proper channels.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220503120001.79272-2-pkshih@realtek.com
DPK is short for digital pre-distortion calibration. It can adjusts digital
waveform according to PA linear characteristics dynamically to enhance
TX EVM.
Do this calibration when we are going to run on AP channel. To prevent
power offset out of boundary, it monitors thermal and set proper boundary
to register.
8852c needs two backup buffers, so we enlarge the array. But, 8852a still
needs only one, so it only uses first element (index zero).
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220502235408.15052-9-pkshih@realtek.com
IQ signal calibration is a very important calibration to yield good RF
performance. We do this calibration only if we are going to run on AP
channel. During scanning phase, without this calibration RF performance
is still acceptable because it transmits with low data rate at this phase.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220502235408.15052-8-pkshih@realtek.com
RX DCK is receiver DC calibration. Do this calibration when bringing up
interface and going to run on AP channel.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220502235408.15052-7-pkshih@realtek.com
RCK is synchronize RC calibration. It needs to be triggered only once when
interface is going to up.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220502235408.15052-6-pkshih@realtek.com
TSSI is transmitter signal strength indication, which is a close-loop
hardware circuit to feedback actual transmitting power as a reference for
next transmission.
When we setup channel to connect an AP, it does full calibration. When
switching bands or channels, it needs to reset hardware status to prevent
use wrong feedback of previous transmission.
To do TX power compensation reflecting current temperature, it loads tables
of compensation values into registers according to channel and band group.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220502235408.15052-5-pkshih@realtek.com
LCK is short fro LC Tank calibration. Do this calibration once driver
loads RF parameters table. Since the characteristic can be changed by
temperature, we do this calibration again if difference of thermal value
is over a threshold.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220502235408.15052-4-pkshih@realtek.com
DACK (digital-to-analog converters calibration) is used to calibrate DAC
to output analog signals as expected.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220502235408.15052-3-pkshih@realtek.com
These tables are used by RFK (RF calibration) to set parameters. These
parameters can trigger certain calibration, or configure/reset settings
before and after RF calibrations.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220502235408.15052-2-pkshih@realtek.com
Eliminate the following coccicheck warning:
./drivers/net/wireless/realtek/rtw89/rtw8852c.c:2556:2-3: Unneeded
semicolon
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220427003142.107916-1-yang.lee@linux.alibaba.com
Hardware reports PPDU status containing encoded channel index to driver,
so we decode it and then fill freq and band.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220421120903.73715-14-pkshih@realtek.com
Read thermal value, and then we can use EWMA thermal value to do RF
calibrations if the value is changed over a threshold.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220421120903.73715-13-pkshih@realtek.com
Three chip_ops are implemented in this patch. The ::set_txpwr_ctrl and
::init_txpwr_unit are called when we up interface and then configure TX
power registers to initial values. The ::set_txpwr_ctrl is to configure
'txpwr_ref' to make basic output TX power of OFDM and CCK rate to be the
same. The ::init_txpwr_unit is to initialize TSSI (a method to do TX power
compensation depends on thermal value) control and bandedge.
The ::set_txpwr is called once switching channel. First, it sets TX power
for each rate section (e.g. CCK, OFDM), and then sets TX power offset
between 1SS and 2SS rate. Finally, it sets TX power limit to prevent
power over regulation.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220421120903.73715-12-pkshih@realtek.com
IQK results in hardware has two copies that are used by firmware to switch
these two to support MCC.
This H2C tell firmware the corresponding channel and band of each IQK
results, and currrent one.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220421120903.73715-10-pkshih@realtek.com
When disconnecting, it warns somethings after power is off, and we can't
do HCI IO. So, add this patch to avoid below messages:
rtw89_8852ce 0000:03:00.0: timed out to flush pci txch: 11
rtw89_8852ce 0000:03:00.0: failed to pre-release fwcmd
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220421120903.73715-9-pkshih@realtek.com
RPP is to report certain skb(s) can be freed, and TX BD indicates which
TX descriptors can be freed. Normally, TX BD is happened before RPP.
In low power mode, RPP can happen ahead, so change flow to handle this
case.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220421120903.73715-8-pkshih@realtek.com
In low power mode, we need to pause PCI to configure IMR and PCI ring
index registers accordingly, because the regular registers are power-off
in this mode.
In the transition moment named paused in code, we can't touch ring index,
so don't kick off DMA immediately. Instead, queue them into pending queue,
and kick off after the moment.
There are three low power modes, which are RF off/clock gate/power gate,
but PCI enter low power mode in later two modes only. So, add a mask
to achieve this.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220421120903.73715-7-pkshih@realtek.com
Normally, we re-enable interrupt by napi_poll, but for this special
situation, we must turn it on immediately because napi_poll isn't
scheduled.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220421120903.73715-6-pkshih@realtek.com
In lower power mode, there are very low amount of RX, and it must process
in a separated function instead of schedule_napi(), because the existing
napi_poll does many things to optimize performance, but not all registers
can access in low power mode. The simple way is to use threadfn to process
the simple thing.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220421120903.73715-5-pkshih@realtek.com
To reclaim TX BD, we need to read hardware reading index to determine if
any DMA is complete. Since this IO spends time, do this thing only if we
really need it when TX BD has no free buffer corresponding to target skb.
The experimental result shows that reading counter decreases from 26,000
to 130 per second.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220421120903.73715-4-pkshih@realtek.com
RPWM/CPWM are registers that can set and check low power mode. Since chips
use different address, add a field to access them in common flow.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220421120903.73715-3-pkshih@realtek.com
8852CE uses different but similar IMR/ISR registers, and its masks are also
different in various states, so add config_intr_mask ops to configure masks
according to under_recovery or low_power states.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220421120903.73715-2-pkshih@realtek.com
During setting channel, we need to backup/restore and disable/enable some
settings. The settings include SCH (scheduler channel), PPDU status report,
and RF components, DFS and ADC.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220414062027.62638-13-pkshih@realtek.com
BB does many settings during setting channel. First is to configure CCK
for 2G channels, and then basic channel and bandwidth settings with a
encoded channel index that will report to driver when we receive packets.
Configure spur elimination to avoid spur of CSI and NBI tones in certain
frequencies. Also, it initializes BT grant to arrange path sharing with
BT according to band. Finally, reset TSSI and BB hardware to ensure it
stays in initial state.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220414062027.62638-12-pkshih@realtek.com
Add parser for bb gain table and configure bb gain table for 8852c.
While ctrl_ch, obtain bb gain error settings and write them to phy.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220414062027.62638-7-pkshih@realtek.com
chip_ops::bb_sethw is to initialize BB settings out of BB parameters
tables. Once switching channel or initialing, we do chip_ops::bb_reset to
reset hardware counters and states to make things in expectation.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220414062027.62638-6-pkshih@realtek.com
