The design of INT indicator register (R_AX_PCIE_HIMR00_V1) is to reduce IO
during frequent interrupts, because it can stop chip sending interrupt to
host if we just set this indicator to 0, not all IMR(s). This indicator
register looks like a root interrupt controller of wifi chip.
However, we can't set all other IMR(s) to 0 during we are running on
interrupt service routine, or the indicator register can't reflect the
status of certain interrupt happened during this period, and then miss
some interrupts especially SER interrupt events.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220516005215.5878-7-pkshih@realtek.com
RPP is to report certain skb(s) can be freed, and TX BD indicates which
TX descriptors can be freed. Normally, TX BD is happened before RPP.
In low power mode, RPP can happen ahead, so change flow to handle this
case.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220421120903.73715-8-pkshih@realtek.com
In low power mode, we need to pause PCI to configure IMR and PCI ring
index registers accordingly, because the regular registers are power-off
in this mode.
In the transition moment named paused in code, we can't touch ring index,
so don't kick off DMA immediately. Instead, queue them into pending queue,
and kick off after the moment.
There are three low power modes, which are RF off/clock gate/power gate,
but PCI enter low power mode in later two modes only. So, add a mask
to achieve this.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220421120903.73715-7-pkshih@realtek.com
Normally, we re-enable interrupt by napi_poll, but for this special
situation, we must turn it on immediately because napi_poll isn't
scheduled.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220421120903.73715-6-pkshih@realtek.com
In lower power mode, there are very low amount of RX, and it must process
in a separated function instead of schedule_napi(), because the existing
napi_poll does many things to optimize performance, but not all registers
can access in low power mode. The simple way is to use threadfn to process
the simple thing.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220421120903.73715-5-pkshih@realtek.com
To reclaim TX BD, we need to read hardware reading index to determine if
any DMA is complete. Since this IO spends time, do this thing only if we
really need it when TX BD has no free buffer corresponding to target skb.
The experimental result shows that reading counter decreases from 26,000
to 130 per second.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220421120903.73715-4-pkshih@realtek.com
RPWM/CPWM are registers that can set and check low power mode. Since chips
use different address, add a field to access them in common flow.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220421120903.73715-3-pkshih@realtek.com
8852CE uses different but similar IMR/ISR registers, and its masks are also
different in various states, so add config_intr_mask ops to configure masks
according to under_recovery or low_power states.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220421120903.73715-2-pkshih@realtek.com
Address info registers are used to configure size of DMA address info to
point skb->data. With different size, it can support different number of
scatters.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220325060055.58482-6-pkshih@realtek.com
The pre_init is used to initialize partial PCI function during PCI probe.
It doesn't need to initialize all functions, so probe can be faster.
Signed-off-by: Chia-Yuan Li <leo.li@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220325060055.58482-4-pkshih@realtek.com
The PCI code of 8852AE and 8852CE are different, but the flow and register
names are similar. To reuse the code, add a struct to define register or
value accordingly. We also use chip id to control the slightly different
flow.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220325060055.58482-2-pkshih@realtek.com
The txdesc is descriptor related to skb->data. The v1 version contains
8 dwords txwd_body and 6 dwords txwd_info, and the format is also different
from original one.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220318023214.32411-10-pkshih@realtek.com
The txaddr_info is used to fill the DMA address of skb->data. The v1
version can support up to 10 entries, but the maximum size of each entry
is 2047, so it fill more than one entry for large packet, like 3000 bytes.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220318023214.32411-9-pkshih@realtek.com
8852A and 8852C use different H2C header and size, so add h2c_desc_size
to allocate different header size and fill content by fill_txdesc_fwcmd.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220318023214.32411-8-pkshih@realtek.com
While SER (system error recover) is processing, it's supposed to mean
something is under recovery. So, disable interrupts (excluding the one
of halt which could be used during SER) to avoid unexpected behavior.
And then, enable interrupts after SER is done.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220314071250.40292-5-pkshih@realtek.com
We have had a struct rtw89_pci_ch_dma_addr to describe register address,
so use it as regular. Since the addresses should be changed dynamically
according to operating mode, I don't change it to be constant.
These changes don't affect the logic, so I put them in this separated
patch.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220307060457.56789-5-pkshih@realtek.com
In the past we use dbi function of wifi mac to read/write
pci config space, but the function will be remove in new
chip. So use kernel api pci_read/write_config_byte instead.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220121075555.12457-2-pkshih@realtek.com
We are planning to support more chipsets, e.g. 8852C. Before that, we
consider architecutre to handle multiple kinds of chipsets. Obviosuly,
based on original design, rtw89_core module will have large size even
if there is only one chipset under running. It is because all chipset
related things are put in rtw89_core now. To reduce such overhead, we
extract modules of rtw89 and adjust dependencies between modules.
The following assumes that 8852AE, 8852AU, and 8852CE are all supported,
we describe the difference before and after extraction.
[Before extraction]
-------------
|------------------------------------ | rtw89_usb |
V -------------
--------------------------------------- -------------
| rtw89_core (including 8852A, 8852C) | <--- | rtw89_pci |
--------------------------------------- -------------
The data of 8852A and 8852C are built in rtw89_core.
And rtw89_pci is the entry of 8852AE and 8852CE.
And rtw89_usb is the entry of 8852AU.
[After extraction]
------------- ----------------
|----------- | rtw89_usb | <-------- | rtw89_8852au |
| ------------- ----------------
V --------------- |
-------------- | | <---------------
| rtw89_core | <--- | rtw89_8852a |
-------------- | | <---------------
^ ^ --------------- |
| | ------------- ----------------
| | | | <-------- | rtw89_8852ae |
| |----------- | rtw89_pci | ----------------
| | | <-----------------
| ------------- |
| --------------- ----------------
|--------------- | rtw89_8852c | <------ | rtw89_8852ce |
--------------- ----------------
The data of 8852A/8852C is extracted to rtw89_8852a/rtw89_8852c.
And rtw89_pci/rtw89_usb handles only common flow of pci/usb bus.
Finally, 8852AE, 8852AU, and 8852CE have individual entry modules,
i.e. rtw89_8852ae, rtw89_8852au, and rtw89_8852ce correspondingly.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211221025828.25092-1-pkshih@realtek.com
This driver named rtw89, which is the next generation of rtw88, supports
Realtek 8852AE 802.11ax 2x2 chip whose new features are OFDMA, DBCC,
Spatial reuse, TWT and BSS coloring; now some of them aren't implemented
though.
The chip architecture is entirely different from the chips supported by
rtw88 like RTL8822CE 802.11ac chip. First of all, register address ranges
are totally redefined, so it's impossible to reuse register definition. To
communicate with firmware, new H2C/C2H format is proposed. In order to have
better utilization, TX DMA flow is changed to two stages DMA. To provide
rich RX status information, additional RX PPDU packets are added.
Since there are so many differences mentioned above, we decide to propose
a new driver. It has many authors, they are listed in alphabetic order:
Chin-Yen Lee <timlee@realtek.com>
Ping-Ke Shih <pkshih@realtek.com>
Po Hao Huang <phhuang@realtek.com>
Tzu-En Huang <tehuang@realtek.com>
Vincent Fann <vincent_fann@realtek.com>
Yan-Hsuan Chuang <tony0620emma@gmail.com>
Zong-Zhe Yang <kevin_yang@realtek.com>
Tested-by: Aaron Ma <aaron.ma@canonical.com>
Tested-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211008035627.19463-1-pkshih@realtek.com
