In low power mode, we need to pause PCI to configure IMR and PCI ring
index registers accordingly, because the regular registers are power-off
in this mode.
In the transition moment named paused in code, we can't touch ring index,
so don't kick off DMA immediately. Instead, queue them into pending queue,
and kick off after the moment.
There are three low power modes, which are RF off/clock gate/power gate,
but PCI enter low power mode in later two modes only. So, add a mask
to achieve this.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220421120903.73715-7-pkshih@realtek.com
TSSI is used to manage TX power with thermal value as a factor. This patch
is to configure bandedge to TX proper waveform.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220414062027.62638-5-pkshih@realtek.com
These parameters are used to initialize BB and RF hardware when we are
going to bring up interface and start to transmit and receive.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220414062027.62638-2-pkshih@realtek.com
In order to support new chip that has capability of 160M, we need new
format to fill new information, so add a new V1 ID for newer use. Since
most fields are the same, fill fields according to the function ID of chip.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220413010804.8941-2-pkshih@realtek.com
Similarly, create functions to set specific C-MAC masks for firmware
recovery.
Signed-off-by: Chia-Yuan Li <leo.li@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220408001353.17188-4-pkshih@realtek.com
These interrupts are used by firmware to recover hardware. Create
functions to set specific D-MAC masks to replace plain register settings.
Signed-off-by: Chia-Yuan Li <leo.li@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220408001353.17188-3-pkshih@realtek.com
The smatch reports:
rtw8852a.c:1857 rtw8852a_btc_set_wl_txpwr_ctrl() error: uninitialized symbol '_cur'.
rtw8852a.c:1858 rtw8852a_btc_set_wl_txpwr_ctrl() error: uninitialized symbol '_cur'.
This is because rtw89_mac_txpwr_read32() can possibly return before setting
argument _cur, and the caller will use the uninitialized value. To fix this
problem, check the return value of rtw89_mac_txpwr_read32().
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220318035202.42437-1-pkshih@realtek.com
The newer chip will generate security header itself, so don't set
IEEE80211_KEY_FLAG_GENERATE_IV in this kind of chip. But, it needs to fill
key_index, PN and 802.11 header length to TX descriptor, and then hardware
uses these to generate security header.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220318023214.32411-11-pkshih@realtek.com
The txdesc is descriptor related to skb->data. The v1 version contains
8 dwords txwd_body and 6 dwords txwd_info, and the format is also different
from original one.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220318023214.32411-10-pkshih@realtek.com
8852A and 8852C use different H2C header and size, so add h2c_desc_size
to allocate different header size and fill content by fill_txdesc_fwcmd.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220318023214.32411-8-pkshih@realtek.com
An export symbol costs about 40 bytes (in x86 with gcc), so use a structure
containing these small arrays to reduce code size.
text data bss dec hex filename
34932 1410 0 36342 8df6 mac.o (before)
34276 1258 0 35534 8ace mac.o (after)
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220315015522.11366-1-pkshih@realtek.com
When FW encounters exception or assertion, SER L2 reset process will start.
It will dump some error information and re-download FW eventually. Since
such errors are usually critical, we would like to keep more information
about error to increase possibility of analysis and debugging FW. We first
add FW payload engine (fw reserved playoad engine, fw_rsvd_ple) memory
dump. FW will record things like CPU registers, backtrace entry, etc. in it
for debugging.
Moreover, device core dump framework is used and wrapped to collect kinds
of dumps during SER L2 reset process.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220314071250.40292-6-pkshih@realtek.com
These function is used to stop transmitting when we are going to switch
channels or do some RF calibration. Before these operations, we need to
stop channel transmission and backup setting into parameter tx_en. After
operations are done, resume transmitting by backup parameter tx_en.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220317055543.40514-13-pkshih@realtek.com
The BT-coexistence uses these function to control antenna and TDMA, so
implement the variant type to support all chips.
Signed-off-by: Chia-Yuan Li <leo.li@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220317055543.40514-10-pkshih@realtek.com
Configure this TX power to indicate TX power offset that uses to transmit
TB (trigger base) uplink frames.
Also, shrink the unit of TX power offset changes to suitable type s8.
Signed-off-by: Yuan-Han Zhang <yuanhan1020@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220317055543.40514-4-pkshih@realtek.com
The dcfo_comp is digital CFO (central frequency offset) compensation.
Since the flow can be shared with all chips, add chip parameters to support
variant register address and format.
Signed-off-by: Yuan-Han Zhang <yuanhan1020@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220317055543.40514-2-pkshih@realtek.com
DAV is an another efuse region that new chip, like 8852C, has this region.
Extend the code to read it, and convert the physical map to logical map
followed by original logical map.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220307060457.56789-12-pkshih@realtek.com
This is a register-based H2C/C2H interface to exchange data with firmware.
Since the register addresses of 8852A and 8852C are different, add fields
to chip_info to support this.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220307060457.56789-9-pkshih@realtek.com
The HCI_FUNC_EN address of 8852C is different from existing chipset, so
add a chip_info::hci_func_en_addr to fill the address individually.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220307060457.56789-8-pkshih@realtek.com
New chipset uses individual power_{on/off} functions to replace old power
sequences, because it is hard to represent new complicated flow in a
sequence table.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220307060457.56789-7-pkshih@realtek.com
For next chipset which can support 6G band, we add the handling
of ieee80211_supported_band for 6G band in advance. And a bitmap,
support_bands, is added to rtw89_chip_info to declare which
NL80211_BAND_* are supported. With the chipset's declaration,
we register the corresponding instances of ieee80211_supported_band
with wiphy.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220113011042.6705-1-pkshih@realtek.com
We are planning to support more chipsets, e.g. 8852C. Before that, we
consider architecutre to handle multiple kinds of chipsets. Obviosuly,
based on original design, rtw89_core module will have large size even
if there is only one chipset under running. It is because all chipset
related things are put in rtw89_core now. To reduce such overhead, we
extract modules of rtw89 and adjust dependencies between modules.
The following assumes that 8852AE, 8852AU, and 8852CE are all supported,
we describe the difference before and after extraction.
[Before extraction]
-------------
|------------------------------------ | rtw89_usb |
V -------------
--------------------------------------- -------------
| rtw89_core (including 8852A, 8852C) | <--- | rtw89_pci |
--------------------------------------- -------------
The data of 8852A and 8852C are built in rtw89_core.
And rtw89_pci is the entry of 8852AE and 8852CE.
And rtw89_usb is the entry of 8852AU.
[After extraction]
------------- ----------------
|----------- | rtw89_usb | <-------- | rtw89_8852au |
| ------------- ----------------
V --------------- |
-------------- | | <---------------
| rtw89_core | <--- | rtw89_8852a |
-------------- | | <---------------
^ ^ --------------- |
| | ------------- ----------------
| | | | <-------- | rtw89_8852ae |
| |----------- | rtw89_pci | ----------------
| | | <-----------------
| ------------- |
| --------------- ----------------
|--------------- | rtw89_8852c | <------ | rtw89_8852ce |
--------------- ----------------
The data of 8852A/8852C is extracted to rtw89_8852a/rtw89_8852c.
And rtw89_pci/rtw89_usb handles only common flow of pci/usb bus.
Finally, 8852AE, 8852AU, and 8852CE have individual entry modules,
i.e. rtw89_8852ae, rtw89_8852au, and rtw89_8852ce correspondingly.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211221025828.25092-1-pkshih@realtek.com
We used to fill in rx skbs' frequency field by mac80211's current
channel value. In some cases, mac80211 switches channel before all
rx packets have been processed. This results in incorrect bss info.
We fix this by filling in frequency field with channel index obtained
from hardware, then fix potential cck missing issue by skb's original
hw rate. After all fix is done, convert hw rate back to the supported
band rate index.
Signed-off-by: Po Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211111023706.14154-3-pkshih@realtek.com
The conditional operator is unnecessary while assigning values to the
bool variables.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Ye Guojin <ye.guojin@zte.com.cn>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211104061119.1685-1-ye.guojin@zte.com.cn
This patch fixes the following Coccinelle warning:
drivers/net/wireless/realtek/rtw89/rtw8852a.c:753:
WARNING possible condition with no effect (if == else)
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Lv Ruyi <lv.ruyi@zte.com.cn>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211021042035.1042463-1-lv.ruyi@zte.com.cn
This driver named rtw89, which is the next generation of rtw88, supports
Realtek 8852AE 802.11ax 2x2 chip whose new features are OFDMA, DBCC,
Spatial reuse, TWT and BSS coloring; now some of them aren't implemented
though.
The chip architecture is entirely different from the chips supported by
rtw88 like RTL8822CE 802.11ac chip. First of all, register address ranges
are totally redefined, so it's impossible to reuse register definition. To
communicate with firmware, new H2C/C2H format is proposed. In order to have
better utilization, TX DMA flow is changed to two stages DMA. To provide
rich RX status information, additional RX PPDU packets are added.
Since there are so many differences mentioned above, we decide to propose
a new driver. It has many authors, they are listed in alphabetic order:
Chin-Yen Lee <timlee@realtek.com>
Ping-Ke Shih <pkshih@realtek.com>
Po Hao Huang <phhuang@realtek.com>
Tzu-En Huang <tehuang@realtek.com>
Vincent Fann <vincent_fann@realtek.com>
Yan-Hsuan Chuang <tony0620emma@gmail.com>
Zong-Zhe Yang <kevin_yang@realtek.com>
Tested-by: Aaron Ma <aaron.ma@canonical.com>
Tested-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211008035627.19463-1-pkshih@realtek.com
