The newer chip will generate security header itself, so don't set
IEEE80211_KEY_FLAG_GENERATE_IV in this kind of chip. But, it needs to fill
key_index, PN and 802.11 header length to TX descriptor, and then hardware
uses these to generate security header.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220318023214.32411-11-pkshih@realtek.com
The txdesc is descriptor related to skb->data. The v1 version contains
8 dwords txwd_body and 6 dwords txwd_info, and the format is also different
from original one.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220318023214.32411-10-pkshih@realtek.com
The txaddr_info is used to fill the DMA address of skb->data. The v1
version can support up to 10 entries, but the maximum size of each entry
is 2047, so it fill more than one entry for large packet, like 3000 bytes.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220318023214.32411-9-pkshih@realtek.com
8852A and 8852C use different H2C header and size, so add h2c_desc_size
to allocate different header size and fill content by fill_txdesc_fwcmd.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220318023214.32411-8-pkshih@realtek.com
Bypass IGI, known as Rx gain, adjustment flow for incompatible hardware
architectures.
Signed-off-by: Johnson Lin <johnson.lin@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220318023214.32411-7-pkshih@realtek.com
Refinement of DIG flow, a mechanism to adjust Rx gain for better Rx
performance, by packing IGI(initial gain index) configuration flow into
one function.
Signed-off-by: Johnson Lin <johnson.lin@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220318023214.32411-6-pkshih@realtek.com
Update notes:
Configure rtw89_regulatory for 6G band according to country.
Adjust country GB to use RTW89_UK entry on all bands.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220318023214.32411-5-pkshih@realtek.com
Wrap regd debug dump into a macro and add dump for 6G band field.
Extend the macro used to configure regd table to account for multiple
bands beyond 2G and 5G.
And the follow-up commit will configure the corresponding values for
6G band into regd table.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220318023214.32411-4-pkshih@realtek.com
Update notes:
TX power by rate table is not changed.
TX power limit table configures values for UK.
TX power limit RU table configures values for UK.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220318023214.32411-3-pkshih@realtek.com
Add RTW89_UK to enum rtw89_regulation_type.
The follow-up commit will configure the corresponding values for it
to TX power tables.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220318023214.32411-2-pkshih@realtek.com
An export symbol costs about 40 bytes (in x86 with gcc), so use a structure
containing these small arrays to reduce code size.
text data bss dec hex filename
34932 1410 0 36342 8df6 mac.o (before)
34276 1258 0 35534 8ace mac.o (after)
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220315015522.11366-1-pkshih@realtek.com
Originally, there is already a mechanism, SER (system error recover),
to deal with HW/FW recovery. After FW v0.13.36.0, FW supports a H2C
(host to chip) command to make a CPU exception. Then, SER is supposed
to catch this FW crash and do L2 reset. This feature is a simulation
to verify if flow of recovering from FW crash works.
Usage of fw_crash debugfs is as the following.
$ echo 1 > fw_crash // trigger FW crash and wait SER handling
$ cat fw_crash // return 0 if restart has been done
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220314071250.40292-9-pkshih@realtek.com
As the fw features gradually increase, it would be better that
we have a set of methods to maintain fw features instead of using
scattered bool variables.
We reconstruct the way fw recognize features, and introduce
RTW89_CHK_FW_FEATURE() / RTW89_SET_FW_FEATURE() to check / set
fw features for uses.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220314071250.40292-8-pkshih@realtek.com
Read FW backtrace entry through FW reserved payload engine, and then
add FW backtrace dump during SER (system error recover) L2 reset process.
It contains a list of RA (return address) and SP (stack pointer) which
gives us a chance to trace back the call stack of FW.
Moreover, if core dump might have wrong content due to error during
dumping, we won't invoke device core dump framework. For this case,
rtw89_ser_cd_free() is added to free buffer by ourselves.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220314071250.40292-7-pkshih@realtek.com
When FW encounters exception or assertion, SER L2 reset process will start.
It will dump some error information and re-download FW eventually. Since
such errors are usually critical, we would like to keep more information
about error to increase possibility of analysis and debugging FW. We first
add FW payload engine (fw reserved playoad engine, fw_rsvd_ple) memory
dump. FW will record things like CPU registers, backtrace entry, etc. in it
for debugging.
Moreover, device core dump framework is used and wrapped to collect kinds
of dumps during SER L2 reset process.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220314071250.40292-6-pkshih@realtek.com
While SER (system error recover) is processing, it's supposed to mean
something is under recovery. So, disable interrupts (excluding the one
of halt which could be used during SER) to avoid unexpected behavior.
And then, enable interrupts after SER is done.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220314071250.40292-5-pkshih@realtek.com
The raw error code might combine error scenario and error status.
But, the error scenario isn't parsed previously. It makes us mishandle
cpu exception and assertion. Now, we correct the error status for them.
Besides, a few uses of error status are refined.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220314071250.40292-4-pkshih@realtek.com
Previously, mac_mem_base_addr_table was declared in debug.c locally
because it's only used via debugfs to dump mac memory. Now, we plan to
refine SER (system error recover) flow which will also need to dump mac
memory to somewhere as information for error which is catched. So, we
move mac_mem_base_addr_table to mac.c rtw89_mac_mem_base_addrs earlier
as common code.
(no logic is changed)
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220314071250.40292-3-pkshih@realtek.com
The CAM, meaning address CAM and bssid CAM here, will get leaks during
SER (system error recover) L2 reset process and ieee80211_restart_hw()
which is called by L2 reset process eventually.
The normal flow would be like
-> add interface (acquire 1)
-> enter ips (release 1)
-> leave ips (acquire 1)
-> connection (occupy 1) <(A) 1 leak after L2 reset if non-sec connection>
The ieee80211_restart_hw() flow (under connection)
-> ieee80211 reconfig
-> add interface (acquire 1)
-> leave ips (acquire 1)
-> connection (occupy (A) + 2) <(B) 1 more leak>
Originally, CAM is released before HW restart only if connection is under
security. Now, release CAM whatever connection it is to fix leak in (A).
OTOH, check if CAM is already valid to avoid acquiring multiple times to
fix (B).
Besides, if AP mode, release address CAM of all stations before HW restart.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220314071250.40292-2-pkshih@realtek.com
Previously we only consider single interface's status, idle mode
behavior could be unexpected when multiple interfaces is active.
Change to enter/leave idle mode by mac80211's configuration state.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220318034316.40720-1-pkshih@realtek.com
The wfx driver is now mature enough to leave the staging area.
Signed-off-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
The intended delay in ath11k_core_suspend is introduced in commit
d1b0c33850 ("ath11k: implement suspend for QCA6390 PCI devices"),
now with ath11k_mac_wait_tx_complete added in commit ba9177fcef
("ath11k: Add basic WoW functionalities"), that delay is not
necessary now, so remove it.
This is found in code review.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-02431-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220331002105.1162099-1-quic_bqiang@quicinc.com
The maximum number of SSIDs in a for active probe requests is currently
reported as 16 (WLAN_SCAN_PARAMS_MAX_SSID) when registering the driver.
The scan_req_params structure only has the capacity to hold 10 SSIDs.
This leads to a buffer overflow which can be triggered from
wpa_supplicant in userspace. When copying the SSIDs into the
scan_req_params structure in the ath11k_mac_op_hw_scan route, it can
overwrite the extraie pointer.
Firmware supports 16 ssid * 4 bssid, for each ssid 4 bssid combo probe
request will be sent, so totally 64 probe requests supported. So
set both max ssid and bssid to 16 and 4 respectively. Remove the
redundant macros of ssid and bssid.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.7.0.1-01300-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Kathirvel <quic_kathirve@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220329150221.21907-1-quic_kathirve@quicinc.com
Remove core PCI and ath11k PCI references(struct ath11k_pci)
from PCI common code. Since, PCI common code will be used
by hybrid bus devices, this code should be independent
from ATH11K PCI references and Linux core PCI references
like struct pci_dev.
Since this change introduces function callbacks for bus wakeup
and bus release operations, wakeup_mhi HW param is no longer
needed and hence it is removed completely. Alternatively, bus
wakeup/release ops for QCA9074 are initialized to NULL as
QCA9704 does not need bus wakeup/release for register accesses.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220328055714.6449-6-quic_mpubbise@quicinc.com
Refactor MSI logic in order to support hybrid bus devices
like WCN6750.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220328055714.6449-5-quic_mpubbise@quicinc.com
Instead of selecting MSI config based on magic numbers, make
the assignment based on HW revision. The logic is similar to
the selection of HW params. This improves readability of the
code and also simplifies new additions.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220328055714.6449-4-quic_mpubbise@quicinc.com
Unlike other ATH11K PCIe devices which are enumerated by APSS
processor (Application Processor SubSystem), WCN6750 gets
enumerated by the WPSS Q6 processor (Wireless Processor SubSystem);
In simple terms, though WCN6750 is PCIe device, it is not attached
to the APSS processor, APSS will not know of such a device being
present in the system and therefore WCN6750 will be registered as
a platform device to the kernel core like other supported AHB
devices.
WCN6750 needs both AHB and PCI APIs for it's operation, it uses
AHB APIs for device probe/boot and PCI APIs for device setup and
register accesses. Because of this nature, it is referred as a
hybrid bus device.
Refactor PCI code to support hybrid bus devices like WCN6750.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220328055714.6449-3-quic_mpubbise@quicinc.com
In order to add the support for WCN6750 in ATH11K , it is
required to move certain PCI definitions to the header file.
As a result, add ATH11K_PCI_* prefix to these definitions.
Also, change the scope of certain PCI APIs that are required
to enable WCN6750 from static to global.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220328055714.6449-2-quic_mpubbise@quicinc.com
This reverts commit 743b9065fe.
The original commit breaks the 256 bitmap in blockack frames in AP
mode. After reverting the commit the feature works again in both AP and
mesh modes
Tested-on: IPQ8074 hw2.0 PCI WLAN.HK.2.6.0.1-00786-QCAHKSWPL_SILICONZ-1
Fixes: 743b9065fe ("ath11k: mesh: add support for 256 bitmap in blockack frames in 11ax")
Signed-off-by: Anilkumar Kolli <quic_akolli@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/1648701477-16367-1-git-send-email-quic_akolli@quicinc.com
Use macros to force strict ordering of the elements.
Signed-off-by: Benjamin Stürz <benni@stuerz.xyz>
Reviewed-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220328212912.283393-1-benni@stuerz.xyz
Replace a "mode" variable indicating "is 5ghz" with an "is2ghz" variable
to make it consistent with other functions in the file.
Signed-off-by: Wenli Looi <wlooi@ucalgary.ca>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220326054754.27812-1-wlooi@ucalgary.ca
commit cfee8793a7 ("ath10k: enable napi on RX path for
sdio") introduced napi for SDIO and updated the htt interface for high
latency devices.
These changes breaks USB, so USB code must be updated to use napi as
well in order to have a working RX path.
Tested-on: QCA9377 hw1.0 USB 1.0.0.299
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220327171340.7893-2-erik.stromdahl@gmail.com
commit 93bbdec6683e1c8ba2cc4e6 ("ath10k: htt: support MSDU ids with
SDIO") introduced MSDU ID allocation in the htt TX path for high latency
devices. This feature needs to be enabled for USB as well in order to
have a functional TX path.
Tested-on: QCA9377 hw1.0 USB 1.0.0.299
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220327171340.7893-1-erik.stromdahl@gmail.com
The ath9k driver was not properly clearing the status area in the
ieee80211_tx_info struct before reporting TX status to mac80211. Instead,
it was manually filling in fields, which meant that fields introduced later
were left as-is.
Conveniently, mac80211 actually provides a helper to zero out the status
area, so use that to make sure we zero everything.
The last commit touching the driver function writing the status information
seems to have actually been fixing an issue that was also caused by the
area being uninitialised; but it only added clearing of a single field
instead of the whole struct. That is now redundant, though, so revert that
commit and use it as a convenient Fixes tag.
Fixes: cc591d77ab ("ath9k: Make sure to zero status.tx_time before reporting TX status")
Reported-by: Bagas Sanjaya <bagasdotme@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
Tested-by: Bagas Sanjaya <bagasdotme@gmail.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220330164409.16645-1-toke@toke.dk
Currently ath11k will wait 11d scan complete while add interface in
ath11k_mac_op_add_interface(), when system resume without enable
wowlan, ath11k_mac_op_add_interface() is called for each resume, thus
it increase the resume time of system. And ath11k_mac_op_hw_scan()
after ath11k_mac_op_add_interface() also needs some time cost because
the previous 11d scan need more than 5 seconds when 6 GHz is enabled,
then the scan started event will indicated to ath11k after the 11d
scan completed.
While 11d scan/hw scan is running in firmware, if ath11k update channel
list to firmware by WMI_SCAN_CHAN_LIST_CMDID, then firmware will cancel
the current scan which is running, it lead the scan failed. The patch
commit 9dcf6808b2 ("ath11k: add 11d scan offload support") used
finish_11d_scan/finish_11d_ch_list/pending_11d to synchronize the 11d
scan/hw scan/channel list between ath11k/firmware/mac80211 and to avoid
the scan fail.
Add wait operation before ath11k update channel list, function
ath11k_reg_update_chan_list() will wait until the current 11d scan/hw
scan completed. And remove the wait operation of start 11d scan and
waiting channel list complete in hw scan. After these changes, resume
time cost reduce about 5 seconds and also hw scan time cost reduced
obviously, and scan failed not seen.
The 11d scan is sent to firmware only one time for each interface added
in mac.c, and it is moved after the 1st hw scan because 11d scan will
cost some time and thus leads the AP scan result update to UI delay.
Currently priority of ath11k's hw scan is WMI_SCAN_PRIORITY_LOW, and
priority of 11d scan in firmware is WMI_SCAN_PRIORITY_MEDIUM, then the
11d scan which sent after hw scan will cancel the hw scan in firmware,
so change the priority to WMI_SCAN_PRIORITY_MEDIUM for the hw scan which
is in front of the 11d scan, thus it will not happen scan cancel in
firmware.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3
Fixes: 9dcf6808b2 ("ath11k: add 11d scan offload support")
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220328035832.14122-1-quic_wgong@quicinc.com
Currently, the driver reports a tx_rate of 6.0 MBit/s no matter the true
rate:
root@linaro-developer:~# iw wlan0 link
Connected to 6c:f3:7f:eb:9b:92 (on wlan0)
SSID: SQ-DEVICETEST
freq: 5200
RX: 4141 bytes (32 packets)
TX: 2082 bytes (15 packets)
signal: -77 dBm
rx bitrate: 135.0 MBit/s MCS 6 40MHz short GI
tx bitrate: 6.0 MBit/s
bss flags: short-slot-time
dtim period: 1
beacon int: 100
This patch requests HAL_GLOBAL_CLASS_A_STATS_INFO via a hal_get_stats
firmware message and reports it via ieee80211_ops::sta_statistics.
root@linaro-developer:~# iw wlan0 link
Connected to 6c:f3:7f:eb:73:b2 (on wlan0)
SSID: SQ-DEVICETEST
freq: 5700
RX: 26788094 bytes (19859 packets)
TX: 1101376 bytes (12119 packets)
signal: -75 dBm
rx bitrate: 135.0 MBit/s MCS 6 40MHz short GI
tx bitrate: 108.0 MBit/s VHT-MCS 5 40MHz VHT-NSS 1
bss flags: short-slot-time
dtim period: 1
beacon int: 100
Tested on MSM8939 with WCN3680B running firmware CNSS-PR-2-0-1-2-c1-00083,
and verified by sniffing frames over the air with Wireshark to ensure the
MCS indices match.
Signed-off-by: Edmond Gagnon <egagnon@squareup.com>
Reviewed-by: Benjamin Li <benl@squareup.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220325224212.159690-1-egagnon@squareup.com
Currently ath11k does not send the country code to firmware after device
recovery, as a result the regdomain info is reported from firmware by
default. Regdomain info is important, so ath11k also need to restore
it to the value which was used before recovery.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220324011856.11014-1-quic_wgong@quicinc.com
This removes some code duplication with le32_to_cpu. This may also be
required for QCN550x support, to provide an abstraction over the
underlying EEPROM format.
Signed-off-by: Wenli Looi <wlooi@ucalgary.ca>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220320233010.123106-7-wlooi@ucalgary.ca
Similar to ar9003_hw_spur_mitigate_mrc_cck, simplify the code by using
ar9003_get_spur_chan_ptr. This may also be required for QCN550x support,
to provide an abstraction over the underlying EEPROM format.
Signed-off-by: Wenli Looi <wlooi@ucalgary.ca>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220320233010.123106-6-wlooi@ucalgary.ca
The current implementation is reading the wrong eeprom type.
Fixes: d8ec2e2a63 ("ath9k: Add an eeprom_ops callback for retrieving the eepmisc value")
Signed-off-by: Wenli Looi <wlooi@ucalgary.ca>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220320233010.123106-5-wlooi@ucalgary.ca
Replace other constants with AR9300_MAX_CHAINS when appropriate.
This change does not appear to affect the final binary.
Signed-off-by: Wenli Looi <wlooi@ucalgary.ca>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220320233010.123106-4-wlooi@ucalgary.ca
This makes the code clearer since set11nRateFlags currently sets
both the rate flags and chain sel. This may also be required for
QCN550x support, where the rate flags and chain sel are in separate
fields.
This change does not appear to affect the final binary.
Signed-off-by: Wenli Looi <wlooi@ucalgary.ca>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220320233010.123106-3-wlooi@ucalgary.ca
This makes the macros more consistent and removes hidden dependencies on
ah for macros that take _ah as a parameter.
This change does not appear to affect the final binary.
Signed-off-by: Wenli Looi <wlooi@ucalgary.ca>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220320233010.123106-2-wlooi@ucalgary.ca
When more clients (128) are connected, the UL data traffic
KPI measurement is low compared to single client. This issue
is due to more CPU cycles spent on the peer lookup operation
with more clients. So reduce the peer lookup operation by
modifying the linear based lookup operation into the rhash
based lookup operation. This improve the peak throughput
measurement. Since this is a software algorithm change, it is
applicable for all the platforms.
TCP UL 128 Clients test case Observation (64bit system):
Previous: ~550 Mbps
Now : ~860 Mbps
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01067-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1644036628-5334-1-git-send-email-quic_periyasa@quicinc.com
This is to read variant from SMBIOS such as read from DT, the variant
string will be used to one part of string which used to search board
data from board-2.bin.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220315104721.26649-3-quic_wgong@quicinc.com
