The is_psr_su parameter is a boolean flag indicating whether the Panel
Self Refresh Selective Update (PSR SU) feature is enabled which is a
power-saving feature that allows only the updated regions of the screen
to be refreshed, reducing the amount of data that needs to be sent to
the display.
Fixes the below with gcc W=1:
drivers/gpu/drm/amd/amdgpu/../display/amdgpu_dm/amdgpu_dm.c:5257: warning: Function parameter or member 'is_psr_su' not described in 'fill_dc_dirty_rects'
Fixes: d16df040c8 ("drm/amdgpu: make damage clips support configurable")
Cc: stable@vger.kernel.org
Cc: Hamza Mahfooz <hamza.mahfooz@amd.com>
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Cc: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Observe error message "Can't retrieve aconnector in hpd_rx_irq_offload_work"
when boot up with a mst tbt4 dock connected. After analyzing, there are few
parts needed to be adjusted:
1. hpd_rx_offload_wq[].aconnector is not initialzed before the dmub outbox
hpd_irq handler get registered which causes the error message.
2. registeration of hpd and hpd_rx_irq event for usb4 dp tunneling is not
aligned with legacy interface sequence
[How]
Put DMUB_NOTIFICATION_HPD and DMUB_NOTIFICATION_HPD_IRQ handler
registration into register_hpd_handlers() to align other interfaces and
get hpd_rx_offload_wq[].aconnector initialized earlier than that.
Leave DMUB_NOTIFICATION_AUX_REPLY registered as it was since we need that
while calling dc_link_detect(). USB4 connection status will be proactively
detected by dc_link_detect_connection_type() in amdgpu_dm_initialize_drm_device()
Cc: Stable <stable@vger.kernel.org>
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Read modify write hazards can occur when using a single shared scratch
register between driver and firmware leading to driver accessing DCN
in IPS2 and a system hang.
[How]
Add infrastructure for using REGION6 as a shared firmware state between
driver and firmware. This region is uncachable.
Replace the existing get/set idle calls with reads/writes to the
(volatile) shared firmware state blocks that a separated by at least
a cache line between firmware and driver.
Remove the workarounds that required rewriting/checking read modify
write hazards.
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The original picture aspect ratio in mode struct may have chance be
overwritten with wrong aspect ratio data in create_stream_for_sink().
It will create a different VIC output and cause HDMI compliance test
failed.
[How]
Preserve the original picture aspect ratio data during create the
stream.
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
As part of a cleanup amdgpu_dm_fini() function, which is typically
called when a device is being shut down or a driver is being unloaded
The below error message suggests that there is a potential null pointer
dereference issue with adev->dm.dc.
In the below, line of code where adev->dm.dc is used without a preceding
null check:
for (i = 0; i < adev->dm.dc->caps.max_links; i++) {
To fix this issue, add a null check for adev->dm.dc before this line.
Reported by smatch:
drivers/gpu/drm/amd/amdgpu/../display/amdgpu_dm/amdgpu_dm.c:1959 amdgpu_dm_fini() error: we previously assumed 'adev->dm.dc' could be null (see line 1943)
Fixes: 006c26a0f1 ("drm/amd/display: Fix crash on device remove/driver unload")
Cc: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Cc: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com>
Reviewed-by: Roman Li <roman.li@amd.com>
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Currently, if the abmlevel module parameter is set, it is possible for
user space to override the ABM level at some point after boot. However,
that is undesirable because it means that we aren't respecting the
user's wishes with regard to the level that they want to use. So,
prevent user space from changing the ABM level if the module parameter
is set to a non-auto value.
Tested-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Since 'adev->dm.dc' in amdgpu_dm_fini() might turn out to be NULL
before the call to dc_enable_dmub_notifications(), check
beforehand to ensure there will not be a possible NULL-ptr-deref
there.
Also, since commit 1e88eb1b2c ("drm/amd/display: Drop
CONFIG_DRM_AMD_DC_HDCP") there are two separate checks for NULL in
'adev->dm.dc' before dc_deinit_callbacks() and dc_dmub_srv_destroy().
Clean up by combining them all under one 'if'.
Found by Linux Verification Center (linuxtesting.org) with static
analysis tool SVACE.
Fixes: 81927e2808 ("drm/amd/display: Support for DMUB AUX")
Signed-off-by: Nikita Zhandarovich <n.zhandarovich@fintech.ru>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We have observed that there are quite a number of PSR-SU panels on the
market that are unable to keep up with what user space throws at them,
resulting in hangs and random black screens. So, make damage clips
support configurable and disable it by default for PSR-SU displays.
Cc: stable@vger.kernel.org
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We want programs besides the compositor to be able to enable or disable
panel power saving features. However, since they are currently only
configurable through DRM properties, that isn't possible. So, to remedy
that issue introduce a new "panel_power_savings" sysfs attribute.
v2: squash in fix from Hamza (Alex)
Cc: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Tested-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add a NULL check for the kzalloc call that allocates memory for
dummy_updates in the amdgpu_dm_atomic_commit_tail function. Previously,
if kzalloc failed to allocate memory and returned NULL, the code would
attempt to use the NULL pointer.
The fix is to check if kzalloc returns NULL, and if so, log an error
message and skip the rest of the current loop iteration with the
continue statement. This prevents the code from attempting to use the
NULL pointer.
Cc: Julia Lawall <julia.lawall@inria.fr>
Cc: Aurabindo Pillai <aurabindo.pillai@amd.com>
Cc: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Cc: Alex Hung <alex.hung@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Reported-by: Julia Lawall <julia.lawall@inria.fr>
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/r/202401300629.ICnCt983-lkp@intel.com/
Fixes: 135fd1b356 ("drm/amd/display: Reduce stack size")
Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com>
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
fix reading edp rx crc timeout failure. after
bootup, kernel setup psr with dpcd 0x170 = 5. this
notify rx psr enable and let rx fw start checking crc
for fw internal logic. rx fw may not update crc read
count within dpcd 0x246. read count is always 0. this
will lead tx crc reading timeout.
[How]
add debugfs to let test app to disbable rx crc
checking for rx internal logic. then test app can read
rx crc dpcd 0x246 successfully.
expected app sequence is as below:
1. disable eDP PHY and notify eDP rx with dpcd 0x600 = 2.
2. echo 0x1 /sys/kernel/debug/dri/0/eDP-X/disallow_edp_enter_psr
3. enable eDP PHY and notify eDP rx with dpcd 0x600 = 1 but
without dpcd 0x170 = 5.
4. read crc from rx dpcd 0x270, 0x246, etc.
5. echo 0x0 /sys/kernel/debug/dri/0/eDP-X/disallow_edp_enter_psr.
this will let eDP back to normal with psr setup dpcd 0x170 = 5.
Reviewed-by: Wayne Lin <wayne.lin@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Hersen Wu <hersenxs.wu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
IPS was temporary disabled due to instability.
It was fixed in dmub firmware and with:
- "drm/amd/display: Add IPS checks before dcn register access"
- "drm/amd/display: Disable ips before dc interrupt setting"
[How]
Enable IPS by default.
Disable IPS if 0x800 bit set in amdgpu.dcdebugmask module params
Signed-off-by: Roman Li <Roman.Li@amd.com>
Tested-by: Mark Broadworth <mark.broadworth@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In dump file, GART memory can be accessed while frame buffer cannot.
[How]
Add GART memory support for dmcub.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Fudongwang <fudong.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
With IPS enabled a system hangs once PSR is active.
PSR active triggers transition to IPS2 state.
While in IPS2 an access to dcn registers results in hard hang.
Existing check doesn't cover for PSR sequence.
[How]
Safeguard register access by disabling idle optimization in atomic commit
and crtc scanout. It will be re-enabled on next vblank.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Return value of 'to_amdgpu_crtc' which is container_of(...) can't be
null, so it's null check 'acrtc' is dropped.
Fixing the below:
drivers/gpu/drm/amd/amdgpu/../display/amdgpu_dm/amdgpu_dm.c:9302 amdgpu_dm_atomic_commit_tail() error: we previously assumed 'acrtc' could be null (see line 9299)
Added 'new_crtc_state' NULL check for function
'drm_atomic_get_new_crtc_state' that retrieves the new state for a CRTC,
while enabling writeback requests.
Cc: stable@vger.kernel.org
Cc: Alex Hung <alex.hung@amd.com>
Cc: Aurabindo Pillai <aurabindo.pillai@amd.com>
Cc: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Cc: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com>
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Enable the Panel Replay if eDP panel and ASIC support.
(prioritize Panel Replay over PSR)
[How]
- Setup the Panel Replay config during the device init
(prioritize Panel Replay over PSR).
- Separate the Replay init function into two functions
amdgpu_dm_link_setup_replay() and amdgpu_dm_set_replay_caps()
to fix the issue in the earlier commit that cause PSR and Replay
enabled at the same time.
Reviewed-by: Sun peng Li <sunpeng.li@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Add regkey to block video playback in IPS2 by default
Allow idle optimizations in the same spot we allow Replay for
video playback usecases.
Avoid sending it when there's an external display connected by
modifying the allow idle checks to check for active non-eDP screens.
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
IGT `amdgpu/amd_color/crtc-lut-accuracy` fails right at the beginning of
the test execution, during atomic check, because DC rejects the
bandwidth state for a fb sizing 64x64. The test was previously working
with the deprecated dc_commit_state(). Now using
dc_validate_with_context() approach, the atomic check needs to perform a
full state validation. Therefore, set fast_validation to false in the
dc_validate_global_state call for atomic check.
Cc: stable@vger.kernel.org
Fixes: b8272241ff ("drm/amd/display: Drop dc_commit_state in favor of dc_commit_streams")
Signed-off-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
These chips needs the same fix. This was previously not seen
on then since the AGP aperture expanded the system aperture,
but this showed up again when AGP was disabled.
Reviewed-and-tested-by: Jiadong Zhu <Jiadong.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The check for sending the vsc infopacket to the display was gated behind
PSR (Panel Self Refresh) being enabled.
The vsc infopacket also contains the colorimetry (specifically the
container color gamut) information for the stream on modern DP.
PSR is typically only supported on mobile phone eDP displays, thus this
was not getting sent for typical desktop monitors or TV screens.
This functionality is needed for proper HDR10 functionality on DP as it
wants BT2020 RGB/YCbCr for the container color space.
Cc: stable@vger.kernel.org
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Xaver Hugl <xaver.hugl@gmail.com>
Cc: Melissa Wen <mwen@igalia.com>
Fixes: 15f9dfd545 ("drm/amd/display: Register Colorspace property for DP and HDMI")
Tested-by: Simon Berz <simon@berz.me>
Tested-by: Xaver Hugl <xaver.hugl@kde.org>
Signed-off-by: Joshua Ashton <joshua@froggi.es>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit 44e60b14d5.
Since, it causes a regression in which eDP displays with PSR support,
but no Replay support (Sink support <= 0x03), fail to enable PSR and
consequently all IGT amd_psr tests fail. So, revert this until a more
suitable fix can be found.
This got brought back accidently with the backmerge.
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Ivan Lipski <ivlipski@amd.com>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
link_rate sometime will be changed when DP MST connector hotplug, so
pbn_div also need be updated; otherwise, it will mismatch with
link_rate, causes no output in external monitor.
Cc: stable@vger.kernel.org
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Jerry Zuo <jerry.zuo@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Wade Wang <wade.wang@hp.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Instability is observed on DCN35 if idle power optimization is enabled.
[How]
Disable IPS until issue is resolved.
Signed-off-by: Roman Li <Roman.Li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY?]
Phantom streams and planes were previously not referenced explcitly on creation.
[HOW?]
To reduce memory management complexity, add an additional phantom streams and planes
reference into dc_state, and move mall_stream_config to stream_status inside
the state to make it safe to modify in shallow copies. Also consildates any logic
that is affected by this change to dc_state.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Jun Lei <jun.lei@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Dillon Varone <dillon.varone@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY?]
Part of the dc_state interface that deals with adding streams and planes should
remain public, while others that deal with internal status' and subvp should be
private to DC.
[HOW?]
Move and rename the public functions to dc_state.h and private functions to
dc_state_priv.h. Also add some additional functions for extracting subvp meta
data from the state.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Jun Lei <jun.lei@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Dillon Varone <dillon.varone@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We can hang in place trying to send commands when the DMCUB isn't
powered on.
[How]
For functions that execute within a DC context or DC lock we can
wrap the direct calls to dm_execute_dmub_cmd/list with code that
exits idle power optimizations and reallows once we're done with
the command submission on success.
For DM direct submissions the DM will need to manage the enter/exit
sequencing manually.
We cannot invoke a DMCUB command directly within the DM execution
helper or we can deadlock.
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Reviewed-by: Hansen Dsouza <hansen.dsouza@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We can hang in place trying to send commands when the DMCUB isn't
powered on.
[How]
We need to exit out of the idle state prior to sending a command,
but the process that performs the exit also invokes a command itself.
Fixing this issue involves the following:
1. Using a software state to track whether or not we need to start
the process to exit idle or notify idle.
It's possible for the hardware to have exited an idle state without
driver knowledge, but entering one is always restricted to a driver
allow - which makes the SW state vs HW state mismatch issue purely one
of optimization, which should seldomly be hit, if at all.
2. Refactor any instances of exit/notify idle to use a single wrapper
that maintains this SW state.
This works simialr to dc_allow_idle_optimizations, but works at the
DMCUB level and makes sure the state is marked prior to any notify/exit
idle so we don't enter an infinite loop.
3. Make sure we exit out of idle prior to sending any commands or
waiting for DMCUB idle.
This patch takes care of 1/2. A future patch will take care of wrapping
DMCUB command submission with calls to this new interface.
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Reviewed-by: Hansen Dsouza <hansen.dsouza@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
On resume from S3, may get apply_idle_optimizations call while DMUB
is inactive which will just time out.
[How]
Set and track power state in dmub_srv and check power state before
sending commands to DMUB. Add interface in both dmub_srv and
dc_dmub_srv
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Samson Tam <samson.tam@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Map the plane CTM driver-specific property to DC plane, instead of DC
stream. The remaining steps to program DPP block are already implemented
on DC shared-code.
v3:
- fix comment about plane and CRTC CTMs priorities (Harry)
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When commiting planes, we copy color mgmt resources to the stream state.
Do the same for shaper and 3D LUTs.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Joshua Ashton <joshua@froggi.es>
Co-developed-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Map plane blend properties to DPP blend gamma. Plane blend is a
post-3D LUT curve that linearizes color space for blending. It may be
defined by a user-blob LUT and/or predefined transfer function. As
hardcoded curve (ROM) is not supported on blend gamma, we use AMD color
module to fill parameters when setting non-linear TF with empty LUT.
v2:
- rename DRM TFs to AMDGPU TFs
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Joshua Ashton <joshua@froggi.es>
Signed-off-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Wire up DC 3D LUT to DM plane color management (pre-blending). On AMD
display HW, 3D LUT comes after a shaper curve and we always have to
program a shaper curve to delinearize or normalize the color space
before applying a 3D LUT (since we have a reduced number of LUT
entries).
In this version, the default values of 3D LUT for size and bit_depth are
17x17x17 and 12-bit, but we already provide here a more generic
mechanisms to program other supported values (9x9x9 size and 10-bit).
v2:
- started with plane 3D LUT instead of CRTC 3D LUT support
v4:
- lut3d_size is the max dimension size instead of # of entries
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Map DC shaper LUT to DM plane color management. Shaper LUT can be used
to delinearize and/or normalize the color space for computational
efficiency and achiving specific visual styles. If a plane degamma is
apply to linearize the color space, a custom shaper 1D LUT can be used
just before applying 3D LUT.
v2:
- use DPP color caps to verify plane 3D LUT support
- add debug message if shaper LUT programming fails
v4:
- remove helper to check 3D LUT color caps (Harry)
- update desc of lut3d-setup helper from MPC to DPP
v5:
- remove color_mgmt_changed check that prevents color updates (Joshua)
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
With `dc_fixpt_from_s3132()` translation, we can just use it to set
hdr_mult.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Joshua Ashton <joshua@froggi.es>
Signed-off-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Set DC plane with user degamma LUT or predefined TF from driver-specific
plane color properties. If plane and CRTC degamma are set in the same
time, plane degamma has priority. That means, we only set CRTC degamma
if we don't have plane degamma LUT or TF to configure. We return -EINVAL
if we don't have plane degamma settings, so we can continue and check
CRTC degamma.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Joshua Ashton <joshua@froggi.es>
Signed-off-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We should reset a plane state if at least one of the color management
properties differs from old and new state.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Joshua Ashton <joshua@froggi.es>
Co-developed-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add predefined transfer function programming. There is no post-blending
out gamma ROM for hardcoded curves, but we can use AMD color modules to
program LUT parameters from pre-defined coefficients and an empty
regamma LUT (or bump up LUT parameters with pre-defined TF values).
v2:
- update crtc color mgmt if regamma TF differs between states (Joshua)
- map inverse EOTF to DC transfer function (Melissa)
v3:
- update AMDGPU TF list
v4:
- update comment regarding regamma behavior
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Joshua Ashton <joshua@froggi.es>
Co-developed-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
'wb_info' needs to be freed on error paths or it would leak the memory.
Smatch pointed this out.
Fixes: c81e13b929 ("drm/amd/display: Hande writeback request from userspace")
Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Replace direct usage of adev->ip_versions with amdgpu_ip_version.
Signed-off-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Hook up driver-specific atomic operations for managing AMD color
properties. Create AMD driver-specific color management properties
and attach them according to HW capabilities defined by `struct
dc_color_caps`.
First add plane degamma LUT properties that means user-blob and its
size. We will add more plane color properties in the next patches. In
addition, we define AMD_PRIVATE_COLOR to guard these driver-specific
plane properties.
Plane degamma can be used to linearize input space for arithmetical
operations that are more accurate when applied in linear color.
v2:
- update degamma LUT prop description
- move private color operations from amdgpu_display to amdgpu_dm_color
v5:
- get degamma blob correctly (Joshua)
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Co-developed-by: Joshua Ashton <joshua@froggi.es>
Signed-off-by: Joshua Ashton <joshua@froggi.es>
Signed-off-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
UAPI Changes:
- Remove Userspace Mode-Setting ioctls
- v3d: New uapi to handle jobs involving the CPU
Cross-subsystem Changes:
Core Changes:
- atomic: Add support for FB-less planes which got reverted a bit
later for lack of IGT tests and userspace code, Dump private objects
state in drm_state_dump.
- dma-buf: Add fence deadline support
- encoder: Create per-encoder debugfs directory, move the bridge chain
file to that directory
Driver Changes:
- Include drm_auth.h in driver that use it but don't include it, Drop
drm_plane_helper.h from drivers that include it but don't use it
- imagination: Plenty of small fixes
- panfrost: Improve interrupt handling at poweroff
- qaic: Convert to persistent DRM devices
- tidss: Support for the AM62A7, a few probe improvements, some cleanups
- v3d: Support for jobs involving the CPU
- bridge:
- Create transparent aux-bridge for DP/USB-C
- lt8912b: Add suspend/resume support and power regulator support
- panel:
- himax-hx8394: Drop prepare, unprepare and shutdown logic, Support
panel rotation
- New panels: BOE BP101WX1-100, Powkiddy X55, Ampire AM8001280G,
Evervision VGG644804, SDC ATNA45AF01
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQRcEzekXsqa64kGDp7j7w1vZxhRxQUCZXGXPAAKCRDj7w1vZxhR
xblIAP4tz7X0mqa7KFr6L0sIfVILHANho4L81IUFi+kpTn64WgEAnqJ3IqJtdLbi
czXzgJPae3Ifstm7CW7+72fLQCR6Cg8=
=pU2c
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2023-12-07' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for 6.8:
UAPI Changes:
- Remove Userspace Mode-Setting ioctls
- v3d: New uapi to handle jobs involving the CPU
Cross-subsystem Changes:
Core Changes:
- atomic: Add support for FB-less planes which got reverted a bit
later for lack of IGT tests and userspace code, Dump private objects
state in drm_state_dump.
- dma-buf: Add fence deadline support
- encoder: Create per-encoder debugfs directory, move the bridge chain
file to that directory
Driver Changes:
- Include drm_auth.h in driver that use it but don't include it, Drop
drm_plane_helper.h from drivers that include it but don't use it
- imagination: Plenty of small fixes
- panfrost: Improve interrupt handling at poweroff
- qaic: Convert to persistent DRM devices
- tidss: Support for the AM62A7, a few probe improvements, some cleanups
- v3d: Support for jobs involving the CPU
- bridge:
- Create transparent aux-bridge for DP/USB-C
- lt8912b: Add suspend/resume support and power regulator support
- panel:
- himax-hx8394: Drop prepare, unprepare and shutdown logic, Support
panel rotation
- New panels: BOE BP101WX1-100, Powkiddy X55, Ampire AM8001280G,
Evervision VGG644804, SDC ATNA45AF01
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maxime Ripard <mripard@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/yu5heqaufyeo4nlowzieu4s5unwqrqyx4jixbfjmzdon677rpk@t53vceua2dao
We currently don't support dirty rectangles on hardware rotated modes.
So, if a user is using hardware rotated modes with PSR-SU enabled,
use PSR-SU FFU for all rotated planes (including cursor planes).
Cc: stable@vger.kernel.org
Fixes: 30ebe41582 ("drm/amd/display: add FB_DAMAGE_CLIPS support")
Reported-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/2952
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Bin Li <binli@gnome.org>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
drm_writeback requires to capture exact one frame in each writeback
call.
[HOW]
frame_capture is disabled after each writeback is completed.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Hardware may require different warmup approaches - big buffer or
individual buffers.
[HOW]
Setup warmup for big buffer when it is required by specific hardware.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHAT]
Add a new field to keep track whether a crtc is previously
writeback-enabled.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
