This reverts commit 6b2b782ad6.
Since, it was causing regression for some DRR scenarios.
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Nevenko Stupar <nevenko.stupar@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
There is only a single call to dc_post_update_surfaces_to_stream
so there is no need to have two flags to control it. Unifying
this to a single flag allows dc_stream_adjust_vmin_vmax to skip
actual programming when there is no change required.
[how]
Remove wm_optimze_required flag and set only optimize_required in its
place. Then in dc_stream_adjust_vmin_vmax, check that the stream timing
range matches the requested one and skip programming if they are equal.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit 6e4337f695.
The original commit causes regression in corner case with HDMI at
specific timings. Reverting from staging to get the full suite to
retest.
Reviewed-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Martin Leung <martin.leung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY?]
Phantom streams and planes were previously not referenced explcitly on creation.
[HOW?]
To reduce memory management complexity, add an additional phantom streams and planes
reference into dc_state, and move mall_stream_config to stream_status inside
the state to make it safe to modify in shallow copies. Also consildates any logic
that is affected by this change to dc_state.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Jun Lei <jun.lei@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Dillon Varone <dillon.varone@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY?]
Part of the dc_state interface that deals with adding streams and planes should
remain public, while others that deal with internal status' and subvp should be
private to DC.
[HOW?]
Move and rename the public functions to dc_state.h and private functions to
dc_state_priv.h. Also add some additional functions for extracting subvp meta
data from the state.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Jun Lei <jun.lei@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Dillon Varone <dillon.varone@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
There is only a single call to dc_post_update_surfaces_to_stream so
there is no need to have two flags to control it. Unifying this to a
single flag allows dc_stream_adjust_vmin_vmax to skip actual
programming when there is no change required.
[how]
Remove wm_optimze_required flag and set only optimize_required in its
place. Then in dc_stream_adjust_vmin_vmax, check that the stream timing
range matches the requested one and skip programming if they are equal.
Reviewed-by: Jun Lei <jun.lei@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
drm_writeback requires to capture exact one frame in each writeback
call.
[HOW]
frame_capture is disabled after each writeback is completed.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit 77a66faacc.
[WHY & HOW]
The writeback series cause a regression in thunderbolt display.
Signed-off-by: Alex Hung <alex.hung@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
drm_writeback requires to capture exact one frame in each writeback
call.
[HOW]
frame_capture is disabled after each writeback is completed.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This was never filled in and thus never truly used.
Checking the EDID for content_type support is not required for sending
the avi infoframe packet.
v2:
- rebase to amd-staging-drm-next
Reviewed-by: Melissa Wen <mwen@igalia.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Joshua Ashton <joshua@froggi.es>
Signed-off-by: Melissa Wen <mwen@igalia.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Implements the 'content type' property for HDMI connectors.
Verified by checking the avi infoframe on a connected TV.
This also simplifies a lot of the code in that area as well, there were
a lot of temp variables doing very little and unnecessary logic
that was quite confusing.
It is not necessary to check for support in the EDID before sending a
'content type' value in the avi infoframe also.
v2:
- rebase to amd-staging-drm-next
- mark CRTC state for reset if content_type differs
Reviewed-by: Harry Wentland <harry.wentland@amd.com> (v1)
Signed-off-by: Joshua Ashton <joshua@froggi.es>
Co-developed-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Melissa Wen <mwen@igalia.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
To organize the edp power control a bit:
1. add flag in dc_link to indicate dc to skip all implicit eDP power control.
2. add edp_set_panel_power link service for DM to call.
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Jun Lei <jun.lei@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Ian Chen <ian.chen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add control flag to dc_stream_state to skip eDP BL off/link off.
Acked-by: Stylon Wang <stylon.wang@amd.com>
Signed-off-by: Max Tseng <max.tseng@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
- For FPO + Vactive cases, we rely on the Vactive display to be at
it's nominal refresh rate because the Vactive pipe may not necessarily
assert P-State allow while it's in VBLANK
- For cases where the Vactive display has a stretched VBLANK due to
VRR, we could underflow when trying to complete an FPO + Vactive
MCLK switch because the FPO display has limited VBLANK time in
waiting for the Vactive display to assert P-State allow naturally
- Block FPO + Vactive if the Vactive display has VRR active (variable
or fixed)
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
To ensure that FAMS can be used, DC must check if there is VRR support.
This commit adds the required configuration to ensure FAMS can be executed in the target system.
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
- Having excessively large margin causes failure in the static
schedulability check in some cases for SubVP + DRR
- 100us of DRR margin is sufficient based on a weeks worth of
stress testing on different display configs
Reviewed-by: Michael Strauss <Michael.Strauss@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
* Pass in pipe index for FPO cmd to DMCUB
- This change will pass in the pipe index for each stream
that is using FPO
- This change is in preparation to enable FPO + VActive
* Use per pipe P-State force for FPO
- For FPO, instead of using max watermarks value for P-State disallow,
use per pipe p-state force instead
- This is in preparation to enable FPO + VActive
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Start enabling AdaptiveSync feature on Linux environment.
[how]
Adding AdaptiveSync support in DC layer
- building AdaptiveSync info_packets
- adjusting the v_startup parameter
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Alan Liu <HaoPing.Liu@amd.com>
Signed-off-by: Sung Joon Kim <sungjoon.kim@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Current secure display only work with single display, now make it
work with multiple displays.
[How]
Create secure_display_context for each crtc instance to store its
own Region of Interest (ROI) information.
v2: squash in warning fix (Alex)
Reviewed-by: Wayne Lin <Wayne.Lin@amd.com>
Acked-by: Jasdeep Dhillon <jdhillon@amd.com>
Signed-off-by: Alan Liu <HaoPing.Liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
- When entering into a SubVP config that requires a minimal
transition we need to retain phantom pipes and also restore
the mall config
- This is because the min transition will remove phantom pipes
from the context (shallow copy) and not restore it's original
state
- This is just a workaround, and needs a proper fix
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Jasdeep Dhillon <jdhillon@amd.com>
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
- Add margin for HUBP "jitter" for SubVp + DRR case
- Also do a min transition even if MPO is added on a
non SubVP pipe (i.e. added on DRR pipe for SubVP + DRR)
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Brian Chang <Brian.Chang@amd.com>
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This commit adds extra documentation for elements related to FAMs.
Tested-by: Mark Broadworth <mark.broadworth@amd.com>
Reviewed-by: Aurabindo Pillai <Aurabindo.Pillai@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
reuse struct rect rather than adding a new struct.
[How]
- Userspace keeps inputting x_start, y_start, x_end, y_end
- We translate data to x, y, width, height in code flow to store
- translate back to x_start, y_start, x_end, y_end before programming HW
Tested-by: Mark Broadworth <mark.broadworth@amd.com>
Reviewed-by: Wayne Lin <Wayne.Lin@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alan Liu <HaoPing.Liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Porting secure display feature from DCN10 to DCN21. Support single
display for now and will extend to multiple displays.
[How]
- use workqueue to offload works for dmub or dmcu firmware
- after receiving ROI update from userspace, set skip_frame_cnt to 1
- refactor amdgpu_dm_crtc_handle_crc_window_irq()
- disable PSR before activating secure_display on a crtc
- check if secure_display is activated before enabling psr
- only work for single display for now.
Tested-by: Mark Broadworth <mark.broadworth@amd.com>
Reviewed-by: Wayne Lin <Wayne.Lin@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alan Liu <HaoPing.Liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The commit stream function does not include surfaces of unaffected
streams, which may lead to some blank screens during mode change in some
edge cases. This commit adds surfaces of unaffected streams followed by
kernel-doc for documenting some of the fields that participate in this
change.
v2: squash in kerneldoc warning fix (Alex)
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Co-developed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Only a single VLINE interrupt is available so interface should not
expose the second one which is used by DMU firmware.
[how]
Remove references to periodic_interrupt1 and VLINE1 from DC interfaces.
Reviewed-by: Jaehyun Chung <jaehyun.chung@amd.com>
Acked-by: Jasdeep Dhillon <jdhillon@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Reprogramming the stream despite no changes in ODM combine mode.
Reprogramming the stream would cause intermittent black screen on
display which could only be recovered through enable/disable sequence.
[HOW]
Fixed bug where we detected a change in ODM combine mode despite ODM
combine mode being disabled. Also removed code which required stream to
be reprogrammed once a change in ODM combine mode was noticed. Lastly we
do not support dynamic ODM switching for HDMI TMDS and FRL on DCN32,
therefore we never want to change its ODM policy.
Reviewed-by: Samson Tam <Samson.Tam@amd.com>
Acked-by: Brian Chang <Brian.Chang@amd.com>
Signed-off-by: Saaem Rizvi <SyedSaaem.Rizvi@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
All references to struct freesync_context were removed, so remove the
struct freesync_context itself and its entry on struct dc_stream_state.
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Maíra Canal <mairacanal@riseup.net>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
With ODM policy 2 to 1, there exists a new use case
scenario where stream content is unchanged, but ODM
may be used. When this happens, the stream needs
to be committed with a new pipe setting.
This did not happen due to stream change
detection logic not accounting for ODM.
[How]
Set ODM flag in stream and commit stream when change
in ODM has been detected due to policy change.
Reviewed-by: Samson Tam <Samson.Tam@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Chris Park <chris.park@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY?]
When adding/removing a plane to some configurations, unsupported pipe
programming can occur when moving to a new plane. Such cases include pipe
split on multi-display, with MPO, and/or ODM.
[HOW?]
Add a safe transistion state that minimizes pipe usage before programming
new configuration. When adding a plane, the current state has the least
pipes required so it is applied without splitting. This must be applied
prior to updating the plane_state for seamless transition. When removing a
plane, the new state has the least pieps required so it is applied without
splitting.
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This commit enables the SubVP feature. To achieve that, we need to:
- Don't force p-state disallow on SubVP (can't block dummy p-state)
- Send calculated watermark to DMCUB for SubVP
- Adjust CAB mode message to PMFW
- Add a proper locking sequence for SubVP
- Various fixes to SubVP static analysis and determining SubVP config
- Currently SubVP not supported with pipe split so merge all pipes
before setting up SubVp
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Alan Liu <HaoPing.Liu@amd.com>
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit 3c4d55c9b9.
Revert the commit because:
- It's incomplete of the function dm_set_dpms_off() for mst case. For
stream sinks whithin the same mst topology, they share the same dc_link.
dm_set_dpms_off() tries to update one mst stream only which is
incomplete.
- Setting dpms off should be triggered by usermode. Besdies, it seems
usermode does release relevant resource for mst & non-mst case when
unplug connecotr now.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Aurabindo Jayamohanan Pillai <Aurabindo.Pillai@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
The display driver on some OSes need to track it in order to
perform memory clock switching decisions.
[HOW]
Propagate the vrr active state to dirty bit so that on mode set it
disables dynamic memory clock switching.
Acked-by: Alan Liu <HaoPing.Liu@amd.com>
Signed-off-by: Harry VanZyllDeJong <harry.vanzylldejong@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
New features will require knowing the vrr mode for their enablement.
[HOW]
Pass the state via a member of dc_stream.
Acked-by: Alan Liu <HaoPing.Liu@amd.com>
Signed-off-by: Felipe Clark <Felipe.Clark@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Video Timing Extended Metadata packet (VTEM) is required for features
like VRR and FVA
[How]
Adding support for VTEM transmission to stream encoders in DCN20 and DCN30
as part of FVA support
Acked-by: Alan Liu <HaoPing.Liu@amd.com>
Signed-off-by: Ahmad Othman <ahmad.othman@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
- Currently there is no support for HF-VSIF
- The current support of VSIF is limited to H14b infoframe
[How]
- refactor VSIF
- Added new builder for HF-VSIF
- Added the HF-VSIF packet to DisplayTarget
- Updates DC to apply HF-VSIF updates when updating streams
Acked-by: Alan Liu <HaoPing.Liu@amd.com>
Signed-off-by: Ahmad Othman <ahmad.othman@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Memory clock switching has great potential for power savings.
[HOW]
The driver code was modified to notify the DMCUB firmware that it should
stretch the vertical blank of frames when a memory clock switch is about
to start so that no blackouts happen on the screen due to unavailability
of the frame buffer.
The driver logic to determine when such firmware assisted strategy can
be initiated is also implemented and consists on checking prerequisites
of the feature.
Acked-by: Alan Liu <HaoPing.Liu@amd.com>
Signed-off-by: Felipe Clark <felipe.clark@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
In PSR-SU design, the DMUB FW handles the combination of multiple
dirty rectangles.
[how]
- create DC dmub update dirty rectangle helper which sends the
dirty rectangles per pipe from DC to DMUB, and DMUB FW will
handle to combine the dirty RECTs
- call the helper from DC commit plane update function.
Signed-off-by: David Zhang <dingchen.zhang@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why&How]
This patch adds necessary changes needed in DC files outside DCN32/321
specific tree
v2: squash in updates (Alex)
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Store current packed PPS data in dc_stream_state for future use.
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Ilya Bakoulin <Ilya.Bakoulin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Implement changes to transition from Pre-OS odm to
Post-OS odm support. Seamless boot case is also
considered.
[HOW]
Revised validation logic when marking for seamless
boot. Init resources accordingly when Pre-OS has
odm enabled. Reset odm and det size when transitioning
Pre-OS odm to Post-OS non-odm to avoid corruption.
Apply logic to set odm accordingly upon commit.
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Pavle Kotarac <Pavle.Kotarac@amd.com>
Signed-off-by: Duncan Ma <Duncan.Ma@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
When we enter FREESYNC_STATE_VIDEO, we want to use the extra vblank
portion to enter zstate if possible.
[how]
When we enter freesync, a full update is triggered and the new vtotal
with extra lines is passed to dml in a stream update. The time gained
from extra vblank lines is calculated in microseconds. We allow zstate
entry if the time gained is greater than 5 ms, which is the current
policy. Furthermore, an optimized value for min_dst_y_next_start is
calculated and written to its register. When exiting freesync, another
full update is triggered and default values are restored.
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Gabe Teeger <gabe.teeger@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We need a helper function in dc to grab the pipe from the stream
context.
[How]
Add it.
Reviewed-by: Martin Leung <Martin.Leung@amd.com>
Acked-by: Agustin Gutierrez <agustin.gutierrez@amd.com>
Signed-off-by: Leo (Hanghong) Ma <hanghong.ma@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
DCN guard is not necessary for DP2.x relevant logic.
Drop them.
v2: squash in fix for misplaced #endif (Alex)
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Reviewed-by: Jerry Zuo <Jerry.Zuo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
configure/call DC interface for DP2 mst support. This is needed to make DP2
mst work.
[How]
- add encoding type, logging, mst update/reduce payload functions
Use the link encoding to determine the DP type (1.4 or 2.0) and add a
flag to dc_stream_update to determine whether to increase/reduce
payloads.
v2:
* add DP_UNKNOWN_ENCODING handling
Signed-off-by: Fangzhi Zuo <Jerry.Zuo@amd.com>
Reviewed-by: "Lin, Wayne" <Wayne.Lin@amd.com>
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211025223825.301703-4-lyude@redhat.com
[How]
Add call to get the last used VTOTAL from DC
Signed-off-by: Jayendran Ramani <Jayendran.Ramani@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
OS uses older flip model which does not work with desktop
VRR causing memory allocations at the wrong IRQ level.
[HOW]
Checks added to flip model to verify model is 2.2 or greater when
doing any of the desktop VRR checks for full updates. This
prevents full updates when VRR changes until a mode change.
Signed-off-by: Harry VanZyllDeJong <hvanzyll@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why & how]
Removing unused DSC flag which is incorrect and is not used.
We are only using stream->timing.flags.DSC for DSC's current
state. Stream state as an input parameter and should not contain
any past status flags.
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Acked-by: Bindu Ramamurthy <bindur12@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
