SoCs making use of Qcom PCIe controller IP v1.0.0 do not support hotplug
functionality. But the hotplug capability bit is set by default in the
hardware. This causes the kernel PCI core to register hotplug service for
the controller and send hotplug commands to it. But those commands will
timeout generating messages as below during boot and suspend/resume.
[ 5.782159] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x03c0 (issued 2020 msec ago)
[ 5.810161] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x03c0 (issued 2048 msec ago)
[ 7.838162] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x07c0 (issued 2020 msec ago)
[ 7.870159] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x07c0 (issued 2052 msec ago)
This not only spams the console output but also induces a delay of a
couple of seconds. To fix this issue, let's clear the HPC bit in
PCI_EXP_SLTCAP register as a part of the post init sequence to not
advertise the hotplug capability for the controller.
Link: https://lore.kernel.org/r/20230619150408.8468-9-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
The post init sequence of IP v2.4.0 is same as v2.3.2. So let's reuse the
v2.3.2 sequence which now also disables hotplug capability of the
controller as it is not at all supported on any SoCs making use of this IP.
Link: https://lore.kernel.org/r/20230619150408.8468-8-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
SoCs making use of Qcom PCIe controller IP v2.3.2 do not support hotplug
functionality. But the hotplug capability bit is set by default in the
hardware. This causes the kernel PCI core to register hotplug service for
the controller and send hotplug commands to it. But those commands will
timeout generating messages as below during boot and suspend/resume.
[ 5.782159] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x03c0 (issued 2020 msec ago)
[ 5.810161] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x03c0 (issued 2048 msec ago)
[ 7.838162] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x07c0 (issued 2020 msec ago)
[ 7.870159] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x07c0 (issued 2052 msec ago)
This not only spams the console output but also induces a delay of a
couple of seconds. To fix this issue, let's clear the HPC bit in
PCI_EXP_SLTCAP register as a part of the post init sequence to not
advertise the hotplug capability for the controller.
Link: https://lore.kernel.org/r/20230619150408.8468-7-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
SoCs making use of Qcom PCIe controller IPs v2.3.3 and v2.9.0 do not
support hotplug functionality. But the hotplug capability bit is set by
default in the hardware. This causes the kernel PCI core to register
hotplug service for the controller and send hotplug commands to it. But
those commands will timeout generating messages as below during boot
and suspend/resume.
[ 5.782159] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x03c0 (issued 2020 msec ago)
[ 5.810161] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x03c0 (issued 2048 msec ago)
[ 7.838162] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x07c0 (issued 2020 msec ago)
[ 7.870159] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x07c0 (issued 2052 msec ago)
This not only spams the console output but also induces a delay of a
couple of seconds. To fix this issue, let's not set the HPC bit in
PCI_EXP_SLTCAP register as a part of the post init sequence to not
advertise the hotplug capability for the controller.
Link: https://lore.kernel.org/r/20230619150408.8468-6-manivannan.sadhasivam@linaro.org
Tested-by: Sricharan Ramabadhran <quic_srichara@quicinc.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
SoCs making use of Qcom PCIe controller IPs v2.7.0 and v1.9.0 do not
support hotplug functionality. But the hotplug capability bit is set by
default in the hardware. This causes the kernel PCI core to register
hotplug service for the controller and send hotplug commands to it. But
those commands will timeout generating messages as below during boot and
suspend/resume.
[ 5.782159] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x03c0 (issued 2020 msec ago)
[ 5.810161] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x03c0 (issued 2048 msec ago)
[ 7.838162] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x07c0 (issued 2020 msec ago)
[ 7.870159] pcieport 0001:00:00.0: pciehp: Timeout on hotplug command 0x07c0 (issued 2052 msec ago)
This not only spams the console output but also induces a delay of a
couple of seconds. To fix this issue, let's clear the HPC bit in
PCI_EXP_SLTCAP register as a part of the post init sequence to not
advertise the hotplug capability for the controller.
Link: https://lore.kernel.org/r/20230619150408.8468-5-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
In the post init sequence of v2.9.0, write access to read only registers
are not disabled after updating the registers. Fix it by disabling the
access after register update.
While at it, let's also add a newline after existing dw_pcie_dbi_ro_wr_en()
guard function to align with rest of the driver.
Link: https://lore.kernel.org/r/20230619150408.8468-4-manivannan.sadhasivam@linaro.org
Fixes: 0cf7c2efe8 ("PCI: qcom: Add IPQ60xx support")
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
DWC core already exposes dw_pcie_dbi_ro_wr_{en/dis} helper APIs for
enabling and disabling the write access to read only DBI registers. So
let's use them instead of doing it manually.
Also, the existing code doesn't disable the write access when it's done.
This is also fixed now.
Link: https://lore.kernel.org/r/20230619150408.8468-3-manivannan.sadhasivam@linaro.org
Fixes: 5d76117f07 ("PCI: qcom: Add support for IPQ8074 PCIe controller")
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
In the post init sequence of v2.9.0, write access to read only registers
are not disabled after updating the registers. Fix it by disabling the
access after register update.
Link: https://lore.kernel.org/r/20230619150408.8468-2-manivannan.sadhasivam@linaro.org
Fixes: 5d76117f07 ("PCI: qcom: Add support for IPQ8074 PCIe controller")
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Cc: <stable@vger.kernel.org>
-----BEGIN PGP SIGNATURE-----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=HPXl
-----END PGP SIGNATURE-----
Merge tag 'pci-v6.4-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull pci updates from Bjorn Helgaas:
"Resource management:
- Add pci_dev_for_each_resource() and pci_bus_for_each_resource()
iterators
PCIe native device hotplug:
- Fix AB-BA deadlock between reset_lock and device_lock
Power management:
- Wait longer for devices to become ready after resume (as we do for
reset) to accommodate Intel Titan Ridge xHCI devices
- Extend D3hot delay for NVIDIA HDA controllers to avoid
unrecoverable devices after a bus reset
Error handling:
- Clear PCIe Device Status after EDR since generic error recovery now
only clears it when AER is native
ASPM:
- Work around Chromebook firmware defect that clobbers Capability
list (including ASPM L1 PM Substates Cap) when returning from
D3cold to D0
Freescale i.MX6 PCIe controller driver:
- Install imprecise external abort handler only when DT indicates
PCIe support
Freescale Layerscape PCIe controller driver:
- Add ls1028a endpoint mode support
Qualcomm PCIe controller driver:
- Add SM8550 DT binding and driver support
- Add SDX55 DT binding and driver support
- Use bulk APIs for clocks of IP 1.0.0, 2.3.2, 2.3.3
- Use bulk APIs for reset of IP 2.1.0, 2.3.3, 2.4.0
- Add DT "mhi" register region for supported SoCs
- Expose link transition counts via debugfs to help debug low power
issues
- Support system suspend and resume; reduce interconnect bandwidth
and turn off clock and PHY if there are no active devices
- Enable async probe by default to reduce boot time
Miscellaneous:
- Sort controller Kconfig entries by vendor"
* tag 'pci-v6.4-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (56 commits)
PCI: xilinx: Drop obsolete dependency on COMPILE_TEST
PCI: mobiveil: Sort Kconfig entries by vendor
PCI: dwc: Sort Kconfig entries by vendor
PCI: Sort controller Kconfig entries by vendor
PCI: Use consistent controller Kconfig menu entry language
PCI: xilinx-nwl: Add 'Xilinx' to Kconfig prompt
PCI: hv: Add 'Microsoft' to Kconfig prompt
PCI: meson: Add 'Amlogic' to Kconfig prompt
PCI: Use of_property_present() for testing DT property presence
PCI/PM: Extend D3hot delay for NVIDIA HDA controllers
dt-bindings: PCI: qcom: Document msi-map and msi-map-mask properties
PCI: qcom: Add SM8550 PCIe support
dt-bindings: PCI: qcom: Add SM8550 compatible
PCI: qcom: Add support for SDX55 SoC
dt-bindings: PCI: qcom-ep: Fix the unit address used in example
dt-bindings: PCI: qcom: Add SDX55 SoC
dt-bindings: PCI: qcom: Update maintainers entry
PCI: qcom: Enable async probe by default
PCI: qcom: Add support for system suspend and resume
PCI/PM: Drop pci_bridge_wait_for_secondary_bus() timeout parameter
...
Add the "Amlogic" vendor name to the CONFIG_PCI_MESON Kconfig prompt to
match other PCIe drivers. Capitalize "Meson" to match other Meson Kconfig
prompts.
Link: https://lore.kernel.org/r/20230418174336.145585-2-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Yue Wang <yue.wang@Amlogic.com>
- Use correct PCIE20_PARF_AXI_MSTR_WR_ADDR_HALT_V2 register for v2.7.0
(Manivannan Sadhasivam)
- Remove "PCIE20_" prefix from register definitions (Manivannan Sadhasivam)
- Sort registers and bitfield declarations (Manivannan Sadhasivam)
- Convert to GENMASK and FIELD_PREP (Manivannan Sadhasivam)
- Use bulk APIs for clocks of IP 1.0.0, 2.3.2, 2.3.3 (Manivannan
Sadhasivam)
- Use bulk APIs for reset of IP 2.1.0, 2.3.3, 2.4.0 (Manivannan Sadhasivam)
- Rename qcom_pcie_config_sid_sm8250() to be non SM8250-specific
(Manivannan Sadhasivam)
- Add DT "mhi" register region for supported SoCs (Manivannan Sadhasivam)
- Expose link transition counts via debugfs to help debug low power issues
(Manivannan Sadhasivam)
- Support system suspend and resume; reduce interconnect bandwidth and turn
off clock and PHY if there are no active devices (Manivannan Sadhasivam)
- Enable async probe by default to reduce boot time (Manivannan Sadhasivam)
- Add Manivannan Sadhasivam as qcom DT binding maintainer, replacing
Stanimir Varbanov (Manivannan Sadhasivam)
- Add DT binding and driver support for Qcom SDX55 SoC (Manivannan
Sadhasivam)
- Add DT binding and driver support for SM8550 SoC (Abel Vesa)
- Document msi-map and msi-map-mask DT properties (Manivannan Sadhasivam)
* pci/controller/qcom:
dt-bindings: PCI: qcom: Document msi-map and msi-map-mask properties
PCI: qcom: Add SM8550 PCIe support
dt-bindings: PCI: qcom: Add SM8550 compatible
PCI: qcom: Add support for SDX55 SoC
dt-bindings: PCI: qcom-ep: Fix the unit address used in example
dt-bindings: PCI: qcom: Add SDX55 SoC
dt-bindings: PCI: qcom: Update maintainers entry
PCI: qcom: Enable async probe by default
PCI: qcom: Add support for system suspend and resume
PCI: qcom: Expose link transition counts via debugfs
dt-bindings: PCI: qcom: Add "mhi" register region to supported SoCs
PCI: qcom: Rename qcom_pcie_config_sid_sm8250() to reflect IP version
PCI: qcom: Use macros for defining total no. of clocks & supplies
PCI: qcom: Use bulk reset APIs for handling resets for IP rev 2.4.0
PCI: qcom: Use bulk reset APIs for handling resets for IP rev 2.3.3
PCI: qcom: Use bulk clock APIs for handling clocks for IP rev 2.3.3
PCI: qcom: Use bulk clock APIs for handling clocks for IP rev 2.3.2
PCI: qcom: Use bulk clock APIs for handling clocks for IP rev 1.0.0
PCI: qcom: Use bulk reset APIs for handling resets for IP rev 2.1.0
PCI: qcom: Use lower case for hex
PCI: qcom: Add missing macros for register fields
PCI: qcom: Use bitfield definitions for register fields
PCI: qcom: Sort and group registers and bitfield definitions
PCI: qcom: Remove PCIE20_ prefix from register definitions
PCI: qcom: Fix the incorrect register usage in v2.7.0 config
SM8550 requires two additional clocks for proper working.
Add these two clocks as optional clocks (as only required by this
platform) and compatible for this platform.
While at it, let's also rename the reset variable to "rst" from
"pci_reset" to match the existing naming preference.
Link: https://lore.kernel.org/r/20230320144658.1794991-2-abel.vesa@linaro.org
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
[lpieralisi@kernel.org: commit log rewording]
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Add support for SDX55 SoC reusing the 1.9.0 config. The PCIe controller is
of version 1.10.0 but it is compatible with the 1.9.0 config. This SoC also
requires "sleep" clock which is added as an optional clock in the driver,
since it is not required on other SoCs.
Link: https://lore.kernel.org/r/20230308082424.140224-14-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Qcom PCIe RC driver waits for the PHY link to be up during the probe;
this consumes several milliseconds during boot.
Enable async probe by default so that other drivers can load in parallel
while this driver waits for the link to be up.
Suggested-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230320064644.5217-1-manivannan.sadhasivam@linaro.org
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
During the system suspend, vote for minimal interconnect bandwidth (1KiB)
to keep the interconnect path active for config access and also turn OFF
the resources like clock and PHY if there are no active devices connected
to the controller. For the controllers with active devices, the resources
are kept ON as removing the resources will trigger access violation during
the late end of suspend cycle as kernel tries to access the config space of
PCIe devices to mask the MSIs.
Also, it is not desirable to put the link into L2/L3 state as that
implies VDD supply will be removed and the devices may go into powerdown
state. This will affect the lifetime of storage devices like NVMe.
And finally, during resume, turn ON the resources if the controller was
truly suspended (resources OFF) and update the interconnect bandwidth
based on PCIe Gen speed.
Suggested-by: Krishna chaitanya chundru <quic_krichai@quicinc.com>
Link: https://lore.kernel.org/r/20230403154922.20704-2-manivannan.sadhasivam@linaro.org
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Acked-by: Dhruva Gole <d-gole@ti.com>
Qualcomm PCIe controllers have debug registers in the MHI region that
count PCIe link transitions. Expose them over debugfs to userspace to
help debug the low power issues.
Note that even though the registers are prefixed as PARF_, they don't
live under the "parf" register region. The register naming is following
the Qualcomm's internal documentation as like other registers.
While at it, let's arrange the local variables in probe function to follow
reverse XMAS tree order.
Link: https://lore.kernel.org/r/20230316081117.14288-20-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
qcom_pcie_config_sid_sm8250() function no longer applies only to SM8250.
So let's rename it to reflect the actual IP version and also move its
definition to keep it sorted as per IP revisions.
Link: https://lore.kernel.org/r/20230316081117.14288-15-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
To keep uniformity, let's use macros to define the total number of clocks
and supplies in qcom_pcie_resources_{2_7_0/2_9_0} structs.
Link: https://lore.kernel.org/r/20230316081117.14288-14-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
All the resets are asserted and deasserted at the same time. So the bulk
reset APIs can be used to handle them together. This simplifies the code
a lot.
It should be noted that there were delays in-between the reset asserts and
deasserts. But going by the config used by other revisions, those delays
are not really necessary. So a single delay after all asserts and one after
deasserts is used.
The total number of resets supported is 12 but only ipq4019 is using all of
them.
Link: https://lore.kernel.org/r/20230316081117.14288-13-manivannan.sadhasivam@linaro.org
Tested-by: Sricharan Ramabadhran <quic_srichara@quicinc.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
All the resets are asserted and deasserted at the same time. So the bulk
reset APIs can be used to handle them together. This simplifies the code
a lot.
Link: https://lore.kernel.org/r/20230316081117.14288-12-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
All the clocks are enabled and disabled at the same time. So the bulk clock
APIs can be used to handle them together. This simplifies the code a lot.
Link: https://lore.kernel.org/r/20230316081117.14288-11-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
All the clocks are enabled and disabled at the same time. So the bulk clock
APIs can be used to handle them together. This simplifies the code a lot.
Link: https://lore.kernel.org/r/20230316081117.14288-10-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
All the clocks are enabled and disabled at the same time. So the bulk clock
APIs can be used to handle them together. This simplifies the code a lot.
Link: https://lore.kernel.org/r/20230316081117.14288-9-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
All the resets are asserted and deasserted at the same time. So the bulk
reset APIs can be used to handle them together. This simplifies the code
a lot.
While at it, let's also move the qcom_pcie_resources_2_1_0 struct below
qcom_pcie_resources_1_0_0 to keep it sorted.
Link: https://lore.kernel.org/r/20230316081117.14288-8-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Some of the registers are changed using hardcoded bitfields without macros.
This provides no information on what the register setting is about. So add
the macros to those fields for making the code more understandable.
Link: https://lore.kernel.org/r/20230316081117.14288-6-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
To maintain uniformity throughout the driver and also to make the code
easier to read, let's make use of bitfield definitions for register fields.
Link: https://lore.kernel.org/r/20230316081117.14288-5-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Sorting the registers and their bit definitions will make it easier to add
more definitions in the future and it also helps in maintenance.
While at it, let's also group the registers and bit definitions separately
as done in the pcie-qcom-ep driver.
Link: https://lore.kernel.org/r/20230316081117.14288-4-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
The PCIE part is redundant and 20 doesn't represent anything across the
SoCs supported now. So let's get rid of the prefix.
This involves adding the IP version suffix to one definition of
PARF_SLV_ADDR_SPACE_SIZE that defines offset specific to that version.
The other definition is generic for the rest of the versions.
Also, the register PCIE20_LNK_CONTROL2_LINK_STATUS2 is not used anywhere,
hence removed.
Link: https://lore.kernel.org/r/20230316081117.14288-3-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Qcom PCIe IP version v2.7.0 and its derivatives don't contain the
PCIE20_PARF_AXI_MSTR_WR_ADDR_HALT register. Instead, they have the new
PCIE20_PARF_AXI_MSTR_WR_ADDR_HALT_V2 register. So fix the incorrect
register usage which is modifying a different register.
Also in this IP version, this register change doesn't depend on MSI
being enabled. So remove that check also.
Link: https://lore.kernel.org/r/20230316081117.14288-2-manivannan.sadhasivam@linaro.org
Fixes: ed8cc3b1fc ("PCI: qcom: Add support for SDM845 PCIe controller")
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Cc: <stable@vger.kernel.org> # 5.6+
commit bb38919ec5 ("PCI: imx6: Add support for i.MX6 PCIe controller")
added a fault hook to this driver in the probe function. So it was only
installed if needed.
commit bde4a5a00e ("PCI: imx6: Allow probe deferral by reset GPIO")
moved it from probe to driver init which installs the hook unconditionally
as soon as the driver is compiled into a kernel.
When this driver is compiled as a module, the hook is not registered
until after the driver has been matched with a .compatible and
loaded.
commit 415b6185c5 ("PCI: imx6: Fix config read timeout handling")
extended the fault handling code.
commit 2d8ed461db ("PCI: imx6: Add support for i.MX8MQ")
added some protection for non-ARM architectures, but this does not
protect non-i.MX ARM architectures.
Since fault handlers can be triggered on any architecture for different
reasons, there is no guarantee that they will be triggered only for the
assumed situation, leading to improper error handling (i.MX6-specific
imx6q_pcie_abort_handler) on foreign systems.
I had seen strange L3 imprecise external abort messages several times on
OMAP4 and OMAP5 devices and couldn't make sense of them until I realized
they were related to this unused imx6q driver because I had
CONFIG_PCI_IMX6=y.
Note that CONFIG_PCI_IMX6=y is useful for kernel binaries that are designed
to run on different ARM SoC and be differentiated only by device tree
binaries. So turning off CONFIG_PCI_IMX6 is not a solution.
Therefore we check the compatible in the init function before registering
the fault handler.
Link: https://lore.kernel.org/r/e1bcfc3078c82b53aa9b78077a89955abe4ea009.1678380991.git.hns@goldelico.com
Fixes: bde4a5a00e ("PCI: imx6: Allow probe deferral by reset GPIO")
Fixes: 415b6185c5 ("PCI: imx6: Fix config read timeout handling")
Fixes: 2d8ed461db ("PCI: imx6: Add support for i.MX8MQ")
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Richard Zhu <hongxing.zhu@nxp.com>
If CDM_CHECK is enabled (by the DT "snps,enable-cdm-check" property), 'val'
is overwritten by PCIE_PL_CHK_REG_CONTROL_STATUS initialization. Commit
ec7b952f45 ("PCI: dwc: Always enable CDM check if "snps,enable-cdm-check"
exists") did not account for further usage of 'val', so we wrote improper
values to PCIE_PORT_LINK_CONTROL when the CDM check is enabled.
Move the PCIE_PORT_LINK_CONTROL update to be completely after the
PCIE_PL_CHK_REG_CONTROL_STATUS register initialization.
[bhelgaas: commit log adapted from Serge's version]
Fixes: ec7b952f45 ("PCI: dwc: Always enable CDM check if "snps,enable-cdm-check" exists")
Link: https://lore.kernel.org/r/20230310123510.675685-2-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Add PCIe EP mode support for ls1028a.
Link: https://lore.kernel.org/r/20230209151050.233973-1-Frank.Li@nxp.com
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Alok Tiwari <alok.a.tiwari@oracle.com>
Acked-by: Roy Zang <Roy.Zang@nxp.com>
pcie-kirin uses regmaps, and needs to pull them in; otherwise, with
CONFIG_PCIE_KIRIN=y and without CONFIG_REGMAP_MMIO pcie-kirin produces
a linker failure looking for __devm_regmap_init_mmio_clk().
Fixes: d19afe7be1 ("PCI: kirin: Use regmap for APB registers")
Link: https://lore.kernel.org/r/04636141da1d6d592174eefb56760511468d035d.1668410580.git.josh@joshtriplett.org
Signed-off-by: Josh Triplett <josh@joshtriplett.org>
[lpieralisi@kernel.org: commit log and removed REGMAP select]
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Cc: stable@vger.kernel.org # 5.16+
-----BEGIN PGP SIGNATURE-----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=/y4d
-----END PGP SIGNATURE-----
Merge tag 'pci-v6.3-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull PCI updates from Bjorn Helgaas:
"Enumeration:
- Rework portdrv shutdown so it disables interrupts but doesn't
disable bus mastering, which leads to hangs on Loongson LS7A
- Add mechanism to prevent Max_Read_Request_Size (MRRS) increases,
again to avoid hardware issues on Loongson LS7A (and likely other
devices based on DesignWare IP)
- Ignore devices with a firmware (DT or ACPI) node that says the
device is disabled
Resource management:
- Distribute spare resources to unconfigured hotplug bridges at
boot-time (not just when hot-adding such a bridge), which makes
hot-adding devices to docks work better. Tried this in v6.1 but had
to revert for regressions, so try again
- Fix root bus issue that dropped resources that happened to end
at 0, e.g., [bus 00]
PCI device hotplug:
- Remove device locking when marking device as disconnected so this
doesn't have to wait for concurrent driver bind/unbind to complete
- Quirk more Qualcomm bridges that don't fully implement the PCIe
Slot Status 'Command Completed' bit
Power management:
- Account for _S0W of the target bridge in acpi_pci_bridge_d3() so we
don't miss hot-add notifications for USB4 docks, Thunderbolt, etc
Reset:
- Observe delay after reset, e.g., resuming from system sleep,
regardless of whether a bridge can suspend to D3cold at runtime
- Wait for secondary bus to become ready after a bridge reset
Virtualization:
- Avoid FLR on some AMD FCH AHCI adapters where it doesn't work
- Allow independent IOMMU groups for some Wangxun NICs that prevent
peer-to-peer transactions but don't advertise an ACS Capability
Error handling:
- Configure End-to-End-CRC (ECRC) only if Linux owns the AER
Capability
- Remove redundant Device Control Error Reporting Enable in the AER
service driver since this is already done for all devices during
enumeration
ASPM:
- Add pci_enable_link_state() interface to allow drivers to enable
ASPM link state
Endpoint framework:
- Move dra7xx and tegra194 linkup processing from hard IRQ to
threaded IRQ handler
- Add a separate lock for endpoint controller list of endpoint
function drivers to prevent deadlock in callbacks
- Pass events from endpoint controller to endpoint function drivers
via callbacks instead of notifiers
Synopsys DesignWare eDMA controller driver (acked by Vinod):
- Fix CPU vs PCI address issues
- Fix source vs destination address issues
- Fix issues with interleaved transfer semantics
- Fix channel count initialization issue (issue still exists in
several other drivers)
- Clean up and improve debugfs usage so it will work on platforms
with several eDMA devices
Baikal T-1 PCIe controller driver:
- Set a 64-bit DMA mask
Freescale i.MX6 PCIe controller driver:
- Add i.MX8MM, i.MX8MQ, i.MX8MP endpoint mode DT binding and driver
support
Intel VMD host bridge driver:
- Add quirk to configure PCIe ASPM and LTR. This is normally done by
BIOS, and will be for future products
Marvell MVEBU PCIe controller driver:
- Mark this driver as broken in Kconfig since bugs prevent its daily
usage
MediaTek MT7621 PCIe controller driver:
- Delay PHY port initialization to improve boot reliability for ZBT
WE1326, ZBT WF3526-P, and some Netgear models
Qualcomm PCIe controller driver:
- Add MSM8998 DT compatible string
- Unify MSM8996 and MSM8998 clock orderings
- Add SM8350 DT binding and driver support
- Add IPQ8074 Gen3 DT binding and driver support
- Correct qcom,perst-regs in DT binding
- Add qcom_pcie_host_deinit() so the PHY is powered off and
regulators and clocks are disabled on late host-init errors
Socionext UniPhier Pro5 controller driver:
- Clean up uniphier-ep reg, clocks, resets, and their names in DT
binding
Synopsys DesignWare PCIe controller driver:
- Restrict coherent DMA mask to 32 bits for MSI, but allow controller
drivers to set 64-bit streaming DMA mask
- Add eDMA engine support in both Root Port and Endpoint controllers
Miscellaneous:
- Remove MODULE_LICENSE from boolean drivers so they don't look like
modules so modprobe can complain about them"
* tag 'pci-v6.3-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (86 commits)
PCI: dwc: Add Root Port and Endpoint controller eDMA engine support
PCI: bt1: Set 64-bit DMA mask
PCI: dwc: Restrict only coherent DMA mask for MSI address allocation
dmaengine: dw-edma: Prepare dw_edma_probe() for builtin callers
dmaengine: dw-edma: Depend on DW_EDMA instead of selecting it
dmaengine: dw-edma: Add mem-mapped LL-entries support
PCI: Remove MODULE_LICENSE so boolean drivers don't look like modules
PCI: hv: Drop duplicate PCI_MSI dependency
PCI/P2PDMA: Annotate RCU dereference
PCI/sysfs: Constify struct kobj_type pci_slot_ktype
PCI: hotplug: Allow marking devices as disconnected during bind/unbind
PCI: pciehp: Add Qualcomm quirk for Command Completed erratum
PCI: qcom: Add IPQ8074 Gen3 port support
dt-bindings: PCI: qcom: Add IPQ8074 Gen3 port
dt-bindings: PCI: qcom: Sort compatibles alphabetically
PCI: qcom: Fix host-init error handling
PCI: qcom: Add SM8350 support
dt-bindings: PCI: qcom: Add SM8350
dt-bindings: PCI: qcom-ep: Correct qcom,perst-regs
dt-bindings: PCI: qcom: Unify MSM8996 and MSM8998 clock order
...
- Release previously-requested DW eDMA IRQs if request_irq() fails (Serge
Semin)
- Convert DW eDMA linked-list (ll) and data target (dt) from CPU-relative
addresses to PCI bus addresses (Serge Semin)
- Fix missing src/dst address for interleaved transfers (Serge Semin)
- Enforce the DW eDMA restriction that interleaved transfers must increment
src and dst addresses (Serge Semin)
- Fix some invalid interleaved transfer semantics (Serge Semin)
- Convert CPU-relative addresses to PCI bus addresses for eDMA engine
(Serge Semin)
- Drop chancnt initialization from dw-edma-core, since it is managed by the
dmaengine core, e.g., in dma_async_device_channel_register() (Serge Semin)
- Clean up bogus casting of debugfs_entries.reg addresses (Serge Semin)
- Ignore debugfs file/directory creation errors (Serge Semin)
- Allocate debugfs entries from the heap to prepare for multi-eDMA
platforms (Serge Semin)
- Simplify and rework register accessors to remove another obstacle to
multi-eDMA platforms (Serge Semin)
- Consolidate eDMA read/write channels in a single dma_device to simplify,
better reflect the hardware design, and avoid a debugfs complaint (Serge
Semin)
- Move eDMA-specific debugfs nodes into existing dmaengine subdirectory
(Serge Semin)
- Fix a readq_ch() truncation from 64 to 32 bits (Serge Semin)
- Use existing readq()/writeq rather than hand-coding new ones (Serge
Semin)
- Drop unnecessary data target region allocation in favor of existing
dw_edma_chip members (Serge Semin)
- Use parent device in eDMA controller name to prepare for multi-eDMA
platforms (Serge Semin)
- In addition to the existing MMIO accessors for linked list entries, add
support for ioremapped entries for use by eDMA in Root Ports or local
Endpoints (Serge Semin)
- Convert DW_EDMA_PCIE so it depends on DW_EDMA instead of selecting it
(Serge Semin)
- Allow DWC drivers to set streaming DMA masks larger than 32 bits;
previously both streaming and coherent DMA were limited to 32 bits
because some PCI devices only support coherent 32-bit DMA for MSI (Serge
Semin)
- Set 64-bit streaming and coherent DMA mask for the bt1 driver (Serge
Semin)
- Add DW Root Port and Endpoint controller support for eDMA (Serge Semin)
* pci/controller/dwc:
PCI: dwc: Add Root Port and Endpoint controller eDMA engine support
PCI: bt1: Set 64-bit DMA mask
PCI: dwc: Restrict only coherent DMA mask for MSI address allocation
dmaengine: dw-edma: Prepare dw_edma_probe() for builtin callers
dmaengine: dw-edma: Depend on DW_EDMA instead of selecting it
dmaengine: dw-edma: Add mem-mapped LL-entries support
dmaengine: dw-edma: Skip cleanup procedure if no private data found
dmaengine: dw-edma: Replace chip ID number with device name
dmaengine: dw-edma: Drop DT-region allocation
dmaengine: dw-edma: Use non-atomic io-64 methods
dmaengine: dw-edma: Fix readq_ch() return value truncation
dmaengine: dw-edma: Use DMA engine device debugfs subdirectory
dmaengine: dw-edma: Join read/write channels into a single device
dmaengine: dw-edma: Move eDMA data pointer to debugfs node descriptor
dmaengine: dw-edma: Simplify debugfs context CSRs init procedure
dmaengine: dw-edma: Rename debugfs dentry variables to 'dent'
dmaengine: dw-edma: Convert debugfs descs to being heap-allocated
dmaengine: dw-edma: Add dw_edma prefix to debugfs nodes descriptor
dmaengine: dw-edma: Stop checking debugfs_create_*() return value
dmaengine: dw-edma: Drop unnecessary debugfs reg casts
dmaengine: dw-edma: Drop chancnt initialization
dmaengine: dw-edma: Add PCI bus address getter to the remote EP glue driver
dmaengine: dw-edma: Add CPU to PCI bus address translation
dmaengine: dw-edma: Fix invalid interleaved xfers semantics
dmaengine: dw-edma: Don't permit non-inc interleaved xfers
dmaengine: dw-edma: Fix missing src/dst address of interleaved xfers
dmaengine: dw-edma: Convert ll/dt phys address to PCI bus/DMA address
dmaengine: dw-edma: Release requested IRQs on failure
dmaengine: Fix dma_slave_config.dst_addr description
- Convert dra7xx to threaded IRQ handler (Manivannan Sadhasivam)
- Move tegra194 dw_pcie_ep_linkup() to threaded IRQ handler (Manivannan
Sadhasivam)
- Add a separate lock for the endpoint pci_epf list to avoid deadlock
while running callbacks (Manivannan Sadhasivam)
- Use callbacks instead of notifier chains to signal events from EPC to EPF
drivers (Manivannan Sadhasivam)
- Use link_up() callback in place of LINK_UP notifier (Manivannan
Sadhasivam)
* pci/endpoint:
PCI: endpoint: Use link_up() callback in place of LINK_UP notifier
PCI: endpoint: Use callback mechanism for passing events from EPC to EPF
PCI: endpoint: Use a separate lock for protecting epc->pci_epf list
PCI: tegra194: Move dw_pcie_ep_linkup() to threaded IRQ handler
PCI: dra7xx: Use threaded IRQ handler for "dra7xx-pcie-main" IRQ
Since the DW eDMA core now supports eDMA controllers embedded in locally
accessible DW PCIe Root Ports and Endpoints, register these controllers
when possible.
To do that the DW PCIe core driver needs to perform some preparations
first. First of all, it needs to find the eDMA controller CSRs base
address, whether they are accessible over the Port Logic or iATU unrolled
space. Afterwards it can try to auto-detect the eDMA controller
availability and number of read/write channels. If none are found the
procedure silently returns without error.
Secondly, the platform is supposed to provide either combined or
per-channel IRQ signals. If no valid IRQs set is found, the procedure
returns without error to be backward compatible with platforms where DW
PCIe controllers have eDMA but lack the IRQ description.
Finally, before actually probing the eDMA device we need to allocate LLP
items buffers. After that the DW eDMA can be registered. If registration is
successful, a message regarding the number of detected Read/Write eDMA
channels will be printed to the system as is done for the iATU settings.
Note: the DW PCI controller driver (either host or endpoint mode) is
currently always built-in, so if the DW eDMA core is built as a module
(CONFIG_DW_EDMA=m), eDMA controllers will not be registered even if the
dw-edma module is later loaded.
Link: https://lore.kernel.org/r/20230113171409.30470-28-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Vinod Koul <vkoul@kernel.org>
The DW PCIe Root Port IP core is synthesized with the 64-bit AXI address
bus. Since the device is also equipped with the eDMA engine, explicitly
set the device DMA mask so DMA engine clients can allocate data buffers
anywhere in the 64-bit memory space.
Link: https://lore.kernel.org/r/20230113171409.30470-27-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The MSI target address must be in the lowest 4GB memory to support PCI
peripherals without 64-bit MSI support. Since the allocation is done from
DMA coherent memory, set only the coherent DMA mask, leaving the streaming
DMA mask alone.
Thus streaming DMA operations will work with no artificial limitations. It
will be specifically useful for the eDMA-capable controllers so the
corresponding DMA engine clients would map the DMA buffers with no need for
SWIOTLB for buffers allocated above 4GB.
Add a brief comment about the reason allocating the MSI target address
below 4GB.
Link: https://lore.kernel.org/r/20230113171409.30470-26-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Since 8b41fc4454 ("kbuild: create modules.builtin without
Makefile.modbuiltin or tristate.conf"), MODULE_LICENSE declarations are
used to identify modules. As a consequence, MODULE_LICENSE in non-modules
causes modprobe to misidentify the object file as a module when it is not,
and modprobe might succeed rather than failing with a suitable error
message.
For tristate modules that can be either built-in or loaded at runtime,
modprobe succeeds in both cases:
# modprobe ext4
[exit status zero if CONFIG_EXT4_FS=y or =m]
For boolean modules like the Standard Hot Plug Controller driver (shpchp)
that cannot be loaded at runtime, modprobe should always fail like this:
# modprobe shpchp
modprobe: FATAL: Module shpchp not found in directory /lib/modules/...
[exit status non-zero regardless of CONFIG_HOTPLUG_PCI_SHPC]
but prior to this commit, shpchp_core.c contained MODULE_LICENSE, so
"modprobe shpchp" silently succeeded when it should have failed.
Remove MODULE_LICENSE in files that cannot be built as modules.
[bhelgaas: commit log, squash]
Suggested-by: Luis Chamberlain <mcgrof@kernel.org>
Link: https://lore.kernel.org/r/20230216152410.4312-1-nick.alcock@oracle.com/
Signed-off-by: Nick Alcock <nick.alcock@oracle.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Luis Chamberlain <mcgrof@kernel.org>
Cc: Hitomi Hasegawa <hasegawa-hitomi@fujitsu.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Lorenzo Pieralisi <lpieralisi@kernel.org>
IPQ8074 has one Gen2 and one Gen3 port, with Gen2 port already supported.
Add compatible for Gen3 port which uses the same controller as IPQ6018.
Link: https://lore.kernel.org/r/20230113164449.906002-7-robimarko@gmail.com
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Implement the new host_deinit() callback so that the PHY is powered off
and regulators and clocks are disabled also on late host-init errors.
Link: https://lore.kernel.org/r/20221017114705.8277-2-johan+linaro@kernel.org
Fixes: 82a823833f ("PCI: qcom: Add Qualcomm PCIe controller driver")
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
