The launchtime offset should be corrected according to sections 7.5.2.6 Transmit Scheduling Latency of the Intel Ethernet I225/I226 Software User Manual. Software can compensate the latency between the transmission scheduling and the time that packet is transmitted to the network by setting this GTxOffset register. Without setting this register, there may be a significant delay between the packet scheduling and the network point. This patch helps to reduce the latency for each of the link speed. Before: 10Mbps : 11000 - 13800 nanosecond 100Mbps : 1300 - 1700 nanosecond 1000Mbps : 190 - 600 nanosecond 2500Mbps : 1400 - 1700 nanosecond After: 10Mbps : less than 750 nanosecond 100Mbps : less than 192 nanosecond 1000Mbps : less than 128 nanosecond 2500Mbps : less than 128 nanosecond Test Setup: Talker : Use l2_tai.c to generate the launchtime into packet payload. Listener: Use timedump.c to compute the delta between packet arrival and LaunchTime packet payload. Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com> Signed-off-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com> Acked-by: Sasha Neftin <sasha.neftin@intel.com> Acked-by: Paul Menzel <pmenzel@molgen.mpg.de> Tested-by: Naama Meir <naamax.meir@linux.intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
297 lines
6.9 KiB
C
297 lines
6.9 KiB
C
// SPDX-License-Identifier: GPL-2.0
|
|
/* Copyright (c) 2019 Intel Corporation */
|
|
|
|
#include "igc.h"
|
|
#include "igc_tsn.h"
|
|
|
|
static bool is_any_launchtime(struct igc_adapter *adapter)
|
|
{
|
|
int i;
|
|
|
|
for (i = 0; i < adapter->num_tx_queues; i++) {
|
|
struct igc_ring *ring = adapter->tx_ring[i];
|
|
|
|
if (ring->launchtime_enable)
|
|
return true;
|
|
}
|
|
|
|
return false;
|
|
}
|
|
|
|
static bool is_cbs_enabled(struct igc_adapter *adapter)
|
|
{
|
|
int i;
|
|
|
|
for (i = 0; i < adapter->num_tx_queues; i++) {
|
|
struct igc_ring *ring = adapter->tx_ring[i];
|
|
|
|
if (ring->cbs_enable)
|
|
return true;
|
|
}
|
|
|
|
return false;
|
|
}
|
|
|
|
static unsigned int igc_tsn_new_flags(struct igc_adapter *adapter)
|
|
{
|
|
unsigned int new_flags = adapter->flags & ~IGC_FLAG_TSN_ANY_ENABLED;
|
|
|
|
if (adapter->base_time)
|
|
new_flags |= IGC_FLAG_TSN_QBV_ENABLED;
|
|
|
|
if (is_any_launchtime(adapter))
|
|
new_flags |= IGC_FLAG_TSN_QBV_ENABLED;
|
|
|
|
if (is_cbs_enabled(adapter))
|
|
new_flags |= IGC_FLAG_TSN_QAV_ENABLED;
|
|
|
|
return new_flags;
|
|
}
|
|
|
|
void igc_tsn_adjust_txtime_offset(struct igc_adapter *adapter)
|
|
{
|
|
struct igc_hw *hw = &adapter->hw;
|
|
u16 txoffset;
|
|
|
|
if (!is_any_launchtime(adapter))
|
|
return;
|
|
|
|
switch (adapter->link_speed) {
|
|
case SPEED_10:
|
|
txoffset = IGC_TXOFFSET_SPEED_10;
|
|
break;
|
|
case SPEED_100:
|
|
txoffset = IGC_TXOFFSET_SPEED_100;
|
|
break;
|
|
case SPEED_1000:
|
|
txoffset = IGC_TXOFFSET_SPEED_1000;
|
|
break;
|
|
case SPEED_2500:
|
|
txoffset = IGC_TXOFFSET_SPEED_2500;
|
|
break;
|
|
default:
|
|
txoffset = 0;
|
|
break;
|
|
}
|
|
|
|
wr32(IGC_GTXOFFSET, txoffset);
|
|
}
|
|
|
|
/* Returns the TSN specific registers to their default values after
|
|
* the adapter is reset.
|
|
*/
|
|
static int igc_tsn_disable_offload(struct igc_adapter *adapter)
|
|
{
|
|
struct igc_hw *hw = &adapter->hw;
|
|
u32 tqavctrl;
|
|
int i;
|
|
|
|
wr32(IGC_GTXOFFSET, 0);
|
|
wr32(IGC_TXPBS, I225_TXPBSIZE_DEFAULT);
|
|
wr32(IGC_DTXMXPKTSZ, IGC_DTXMXPKTSZ_DEFAULT);
|
|
|
|
tqavctrl = rd32(IGC_TQAVCTRL);
|
|
tqavctrl &= ~(IGC_TQAVCTRL_TRANSMIT_MODE_TSN |
|
|
IGC_TQAVCTRL_ENHANCED_QAV);
|
|
wr32(IGC_TQAVCTRL, tqavctrl);
|
|
|
|
for (i = 0; i < adapter->num_tx_queues; i++) {
|
|
wr32(IGC_TXQCTL(i), 0);
|
|
wr32(IGC_STQT(i), 0);
|
|
wr32(IGC_ENDQT(i), NSEC_PER_SEC);
|
|
}
|
|
|
|
wr32(IGC_QBVCYCLET_S, 0);
|
|
wr32(IGC_QBVCYCLET, NSEC_PER_SEC);
|
|
|
|
adapter->flags &= ~IGC_FLAG_TSN_QBV_ENABLED;
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int igc_tsn_enable_offload(struct igc_adapter *adapter)
|
|
{
|
|
struct igc_hw *hw = &adapter->hw;
|
|
u32 tqavctrl, baset_l, baset_h;
|
|
u32 sec, nsec, cycle;
|
|
ktime_t base_time, systim;
|
|
int i;
|
|
|
|
cycle = adapter->cycle_time;
|
|
base_time = adapter->base_time;
|
|
|
|
wr32(IGC_TSAUXC, 0);
|
|
wr32(IGC_DTXMXPKTSZ, IGC_DTXMXPKTSZ_TSN);
|
|
wr32(IGC_TXPBS, IGC_TXPBSIZE_TSN);
|
|
|
|
tqavctrl = rd32(IGC_TQAVCTRL);
|
|
tqavctrl |= IGC_TQAVCTRL_TRANSMIT_MODE_TSN | IGC_TQAVCTRL_ENHANCED_QAV;
|
|
wr32(IGC_TQAVCTRL, tqavctrl);
|
|
|
|
wr32(IGC_QBVCYCLET_S, cycle);
|
|
wr32(IGC_QBVCYCLET, cycle);
|
|
|
|
for (i = 0; i < adapter->num_tx_queues; i++) {
|
|
struct igc_ring *ring = adapter->tx_ring[i];
|
|
u32 txqctl = 0;
|
|
u16 cbs_value;
|
|
u32 tqavcc;
|
|
|
|
wr32(IGC_STQT(i), ring->start_time);
|
|
wr32(IGC_ENDQT(i), ring->end_time);
|
|
|
|
if (adapter->base_time) {
|
|
/* If we have a base_time we are in "taprio"
|
|
* mode and we need to be strict about the
|
|
* cycles: only transmit a packet if it can be
|
|
* completed during that cycle.
|
|
*/
|
|
txqctl |= IGC_TXQCTL_STRICT_CYCLE |
|
|
IGC_TXQCTL_STRICT_END;
|
|
}
|
|
|
|
if (ring->launchtime_enable)
|
|
txqctl |= IGC_TXQCTL_QUEUE_MODE_LAUNCHT;
|
|
|
|
/* Skip configuring CBS for Q2 and Q3 */
|
|
if (i > 1)
|
|
goto skip_cbs;
|
|
|
|
if (ring->cbs_enable) {
|
|
if (i == 0)
|
|
txqctl |= IGC_TXQCTL_QAV_SEL_CBS0;
|
|
else
|
|
txqctl |= IGC_TXQCTL_QAV_SEL_CBS1;
|
|
|
|
/* According to i225 datasheet section 7.5.2.7, we
|
|
* should set the 'idleSlope' field from TQAVCC
|
|
* register following the equation:
|
|
*
|
|
* value = link-speed 0x7736 * BW * 0.2
|
|
* ---------- * ----------------- (E1)
|
|
* 100Mbps 2.5
|
|
*
|
|
* Note that 'link-speed' is in Mbps.
|
|
*
|
|
* 'BW' is the percentage bandwidth out of full
|
|
* link speed which can be found with the
|
|
* following equation. Note that idleSlope here
|
|
* is the parameter from this function
|
|
* which is in kbps.
|
|
*
|
|
* BW = idleSlope
|
|
* ----------------- (E2)
|
|
* link-speed * 1000
|
|
*
|
|
* That said, we can come up with a generic
|
|
* equation to calculate the value we should set
|
|
* it TQAVCC register by replacing 'BW' in E1 by E2.
|
|
* The resulting equation is:
|
|
*
|
|
* value = link-speed * 0x7736 * idleSlope * 0.2
|
|
* ------------------------------------- (E3)
|
|
* 100 * 2.5 * link-speed * 1000
|
|
*
|
|
* 'link-speed' is present in both sides of the
|
|
* fraction so it is canceled out. The final
|
|
* equation is the following:
|
|
*
|
|
* value = idleSlope * 61036
|
|
* ----------------- (E4)
|
|
* 2500000
|
|
*
|
|
* NOTE: For i225, given the above, we can see
|
|
* that idleslope is represented in
|
|
* 40.959433 kbps units by the value at
|
|
* the TQAVCC register (2.5Gbps / 61036),
|
|
* which reduces the granularity for
|
|
* idleslope increments.
|
|
*
|
|
* In i225 controller, the sendSlope and loCredit
|
|
* parameters from CBS are not configurable
|
|
* by software so we don't do any
|
|
* 'controller configuration' in respect to
|
|
* these parameters.
|
|
*/
|
|
cbs_value = DIV_ROUND_UP_ULL(ring->idleslope
|
|
* 61036ULL, 2500000);
|
|
|
|
tqavcc = rd32(IGC_TQAVCC(i));
|
|
tqavcc &= ~IGC_TQAVCC_IDLESLOPE_MASK;
|
|
tqavcc |= cbs_value | IGC_TQAVCC_KEEP_CREDITS;
|
|
wr32(IGC_TQAVCC(i), tqavcc);
|
|
|
|
wr32(IGC_TQAVHC(i),
|
|
0x80000000 + ring->hicredit * 0x7735);
|
|
} else {
|
|
/* Disable any CBS for the queue */
|
|
txqctl &= ~(IGC_TXQCTL_QAV_SEL_MASK);
|
|
|
|
/* Set idleSlope to zero. */
|
|
tqavcc = rd32(IGC_TQAVCC(i));
|
|
tqavcc &= ~(IGC_TQAVCC_IDLESLOPE_MASK |
|
|
IGC_TQAVCC_KEEP_CREDITS);
|
|
wr32(IGC_TQAVCC(i), tqavcc);
|
|
|
|
/* Set hiCredit to zero. */
|
|
wr32(IGC_TQAVHC(i), 0);
|
|
}
|
|
skip_cbs:
|
|
wr32(IGC_TXQCTL(i), txqctl);
|
|
}
|
|
|
|
nsec = rd32(IGC_SYSTIML);
|
|
sec = rd32(IGC_SYSTIMH);
|
|
|
|
systim = ktime_set(sec, nsec);
|
|
|
|
if (ktime_compare(systim, base_time) > 0) {
|
|
s64 n;
|
|
|
|
n = div64_s64(ktime_sub_ns(systim, base_time), cycle);
|
|
base_time = ktime_add_ns(base_time, (n + 1) * cycle);
|
|
}
|
|
|
|
baset_h = div_s64_rem(base_time, NSEC_PER_SEC, &baset_l);
|
|
|
|
wr32(IGC_BASET_H, baset_h);
|
|
wr32(IGC_BASET_L, baset_l);
|
|
|
|
return 0;
|
|
}
|
|
|
|
int igc_tsn_reset(struct igc_adapter *adapter)
|
|
{
|
|
unsigned int new_flags;
|
|
int err = 0;
|
|
|
|
new_flags = igc_tsn_new_flags(adapter);
|
|
|
|
if (!(new_flags & IGC_FLAG_TSN_ANY_ENABLED))
|
|
return igc_tsn_disable_offload(adapter);
|
|
|
|
err = igc_tsn_enable_offload(adapter);
|
|
if (err < 0)
|
|
return err;
|
|
|
|
adapter->flags = new_flags;
|
|
|
|
return err;
|
|
}
|
|
|
|
int igc_tsn_offload_apply(struct igc_adapter *adapter)
|
|
{
|
|
int err;
|
|
|
|
if (netif_running(adapter->netdev)) {
|
|
schedule_work(&adapter->reset_task);
|
|
return 0;
|
|
}
|
|
|
|
err = igc_tsn_enable_offload(adapter);
|
|
if (err < 0)
|
|
return err;
|
|
|
|
adapter->flags = igc_tsn_new_flags(adapter);
|
|
return 0;
|
|
}
|