7d96c4a5ec
Use more specific custom GPIO line names which denote exactly where the GPIO came from, i.e. the base board. Also, update the new blank GPIO line names set up by stm32mp15xx-dhcom-som.dtsi back to their original values. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Alexandre Torgue <alexandre.torgue@foss.st.com> Cc: Patrice Chotard <patrice.chotard@foss.st.com> Cc: Patrick Delaunay <patrick.delaunay@foss.st.com> Cc: linux-stm32@st-md-mailman.stormreply.com To: linux-arm-kernel@lists.infradead.org Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
147 lines
2.5 KiB
Text
147 lines
2.5 KiB
Text
// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
|
|
/*
|
|
* Copyright (C) 2020 Marek Vasut <marex@denx.de>
|
|
*/
|
|
|
|
#include <dt-bindings/input/input.h>
|
|
#include <dt-bindings/pwm/pwm.h>
|
|
|
|
/ {
|
|
aliases {
|
|
serial0 = &uart4;
|
|
serial1 = &usart3;
|
|
serial2 = &uart8;
|
|
};
|
|
|
|
chosen {
|
|
stdout-path = "serial0:115200n8";
|
|
};
|
|
|
|
led {
|
|
compatible = "gpio-leds";
|
|
|
|
led-0 {
|
|
label = "yellow:led";
|
|
gpios = <&gpioi 3 GPIO_ACTIVE_HIGH>;
|
|
default-state = "off";
|
|
};
|
|
};
|
|
};
|
|
|
|
&adc {
|
|
status = "disabled";
|
|
};
|
|
|
|
&dac {
|
|
status = "disabled";
|
|
};
|
|
|
|
&fmc {
|
|
status = "disabled";
|
|
};
|
|
|
|
&gpioa {
|
|
/*
|
|
* NOTE: The USB Port on the PicoITX needs a PWR_EN signal to enable
|
|
* port power. This signal should be handled by USB power sequencing
|
|
* in order to turn on port power when USB bus is powered up, but so
|
|
* far there is no such functionality.
|
|
*/
|
|
usb-port-power-hog {
|
|
gpio-hog;
|
|
gpios = <13 0>;
|
|
output-low;
|
|
line-name = "usb-port-power";
|
|
};
|
|
};
|
|
|
|
&gpioc {
|
|
gpio-line-names = "", "", "", "",
|
|
"", "", "PicoITX-In1", "",
|
|
"", "", "", "",
|
|
"", "", "", "";
|
|
};
|
|
|
|
&gpiod {
|
|
gpio-line-names = "", "", "", "",
|
|
"", "", "DHCOM-B", "",
|
|
"", "", "", "PicoITX-Out1",
|
|
"PicoITX-Out2", "", "", "";
|
|
};
|
|
|
|
&gpiog {
|
|
gpio-line-names = "PicoITX-In2", "", "", "",
|
|
"", "", "", "",
|
|
"DHCOM-L", "", "", "",
|
|
"", "", "", "";
|
|
};
|
|
|
|
&i2c2 { /* On board-to-board connector (optional) */
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&i2c2_pins_a>;
|
|
i2c-scl-rising-time-ns = <185>;
|
|
i2c-scl-falling-time-ns = <20>;
|
|
status = "okay";
|
|
/* spare dmas for other usage */
|
|
/delete-property/dmas;
|
|
/delete-property/dma-names;
|
|
};
|
|
|
|
&i2c5 { /* On board-to-board connector */
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&i2c5_pins_a>;
|
|
i2c-scl-rising-time-ns = <185>;
|
|
i2c-scl-falling-time-ns = <20>;
|
|
status = "okay";
|
|
/* spare dmas for other usage */
|
|
/delete-property/dmas;
|
|
/delete-property/dma-names;
|
|
};
|
|
|
|
&ksz8851 {
|
|
status = "disabled";
|
|
};
|
|
|
|
&usart3 {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&usart3_pins_a>;
|
|
status = "okay";
|
|
};
|
|
|
|
&uart8 {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&uart8_pins_a &uart8_rtscts_pins_a>;
|
|
status = "okay";
|
|
};
|
|
|
|
&usbh_ehci {
|
|
phys = <&usbphyc_port0>;
|
|
status = "okay";
|
|
};
|
|
|
|
&usbh_ohci {
|
|
phys = <&usbphyc_port0>;
|
|
status = "okay";
|
|
};
|
|
|
|
&usbotg_hs {
|
|
dr_mode = "otg";
|
|
pinctrl-0 = <&usbotg_hs_pins_a>;
|
|
pinctrl-names = "default";
|
|
phy-names = "usb2-phy";
|
|
phys = <&usbphyc_port1 0>;
|
|
vbus-supply = <&vbus_otg>;
|
|
status = "okay";
|
|
};
|
|
|
|
&usbphyc {
|
|
status = "okay";
|
|
};
|
|
|
|
&usbphyc_port0 {
|
|
phy-supply = <&vdd_usb>;
|
|
};
|
|
|
|
&usbphyc_port1 {
|
|
phy-supply = <&vdd_usb>;
|
|
};
|