This gives us WPA3 support out of the box without having to manually disable
hardware crypto. The driver will fall back to software crypto if the connection
requires management frame protection.
Suggested-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200525134906.1672-1-rsalvaterra@gmail.com
We can not set IV when we are under reset. Previously we read previous
IV value from registers and zeroed IV registers when key was deleted,
but this could possibly not work if DEL_KEY command was not performed.
Now when we have ->reconfig_complete ops and we fully mark mac80211
reset state via DEVICE_STATE_RESET flag, we can just skip setting IV
when keys are set during reset.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
On 2019-10-28 06:07, wbob wrote:
> Hello Roman,
>
> while reading around drivers/net/wireless/ralink/rt2x00/rt2800lib.c
> I stumbled on what I think is an edit of yours made in error in march
> 2017:
>
> https://github.com/torvalds/linux/commit/41977e86#diff-dae5dc10da180f3b055809a48118e18aR5281
>
> RT6352 in line 5281 should not have been introduced as the "else if"
> below line 5291 can then not take effect for a RT6352 device. Another
> possibility is for line 5291 to be not for RT6352, but this seems
> very unlikely. Are you able to clarify still after this substantial time?
>
> 5277: static int rt2800_init_registers(struct rt2x00_dev *rt2x00dev)
> ...
> 5279: } else if (rt2x00_rt(rt2x00dev, RT5390) ||
> 5280: rt2x00_rt(rt2x00dev, RT5392) ||
> 5281: rt2x00_rt(rt2x00dev, RT6352)) {
> ...
> 5291: } else if (rt2x00_rt(rt2x00dev, RT6352)) {
> ...
Hence remove errornous line 5281 to make the driver actually
execute the correct initialization routine for MT7620 chips.
As it was requested by Stanislaw Gruszka remove setting values of
MIMO_PS_CFG and TX_PIN_CFG. MIMO_PS_CFG is responsible for MIMO
power-safe mode (which is disabled), hence we can drop setting it.
TX_PIN_CFG is set correctly in other functions, and as setting this
value breaks some devices, rather don't set it here during init, but
only modify it later on.
Fixes: 41977e86c9 ("rt2x00: add support for MT7620")
Reported-by: wbob <wbob@jify.de>
Reported-by: Roman Yeryomin <roman@advem.lv>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There really is no need to make drivers call the
ieee80211_start_tx_ba_cb_irqsafe() function and then
schedule the worker if all we want is to set a bit.
Add a new return value (that was previously considered
invalid) to indicate that the driver is immediately
ready for the session, and make drivers use it. The
only drivers that remain different are the Intel ones
as they need to negotiate more with the firmware.
Link: https://lore.kernel.org/r/1570007543-I152912660131cbab2e5d80b4218238c20f8a06e5@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This reverts commit 9ad3b55654.
As reported by Sergey:
"I got some problem after upgrade kernel to 5.2 version (debian testing
linux-image-5.2.0-2-amd64). 5Ghz client stopped to see AP.
Some tests with 1metre distance between client-AP: 2.4Ghz -22dBm, for
5Ghz - 53dBm !, for longer distance (8m + walls) 2.4 - 61dBm, 5Ghz not
visible."
It was identified that rx signal level degradation was caused by
9ad3b55654 ("rt2800: enable TX_PIN_CFG_LNA_PE_ bits per band").
So revert this commit.
Cc: <stable@vger.kernel.org> # v5.1+
Reported-and-tested-by: Sergey Maranchuk <slav0nic0@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
After looking at code I realized that my previous fix
9584412438 ("rt2x00: clear IV's on start to fix AP mode regression")
was incomplete. We can still have wrong IV's after re-keyring.
To fix that, clear up IV's also on key removal.
Fixes: 710e6cc159 ("rt2800: do not nullify initialization vector data")
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
tested-by: Emil Karlson <jekarl@iki.fi>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
To do not brake HW restart we should keep initialization vectors data.
I assumed that on start the data is already initialized to zeros, but
that not true on some scenarios and we should clear it. So add
additional flag to check if we are under HW restart and clear IV's
data if we are not.
Patch fixes AP mode regression.
Reported-and-tested-by: Emil Karlson <jekarl@iki.fi>
Fixes: 710e6cc159 ("rt2800: do not nullify initialization vector data")
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Make watchdog disabled by default and add module parameter to enable it.
User will have to create file in /etc/modprobe.d/ with
options rt2800lib watchdog=1
to enable the watchdog or load "rt2800lib watchdog=1" module manually
before loading rt2800{soc,pci,usb} module.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add ieee80211_restart_hw() to watchdog and debugfs file for testing
if restart works as expected.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If we restart hw we should keep existing IV (initialization vector)
otherwise HW encryption will be broken after restart.
Also fix some coding style issues on the way.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add routine to cleanup interfaces data before hw reset as
ieee80211_restart_hw() will do setup interfaces again.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add watchdog for rt2800 devices. For now it only detect hung
and print error.
[Note: I verified that printing messages from process context is
fine on MT7620 (WT3020) platform that have problem when printk
is called from interrupt context].
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not see http www gnu org licenses
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details [based]
[from] [clk] [highbank] [c] you should have received a copy of the
gnu general public license along with this program if not see http
www gnu org licenses
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 355 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Jilayne Lovejoy <opensource@jilayne.com>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190519154041.837383322@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Patch add support for RT3883 chip. Code was taken direclty
from openwrt project and merge into one patch.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We do not any longer check txstatus timeout from tasklet, so do not need
this optimization.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Move rt2800usb_txstatus_pending routine to rt2800lib. It will be reused
by rt2800mmio code.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Do not disable txstatus interrupt and add quota of processed tx statuses in
one tasklet. Quota is needed to allow to fed device with new frames during
processing of tx statuses.
Patch fixes about 15% performance degradation on some scenarios caused by
0b0d556e0e ("rt2800mmio: use txdone/txstatus routines from lib").
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We do not need separate lines for calculating register values.
Also add comment that value is different than in vendor driver.
Suggested-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The TX_PIN_CFG_RFRX_EN bit was not set on other devices than MT7620,
restore old behavaviour since setting this bit maight not be
correct for older devices.
Fixes: 41977e86c9 ("rt2x00: add support for MT7620")
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Do not enable TX_PIN_CFG_LNA_PE_A* bits for 2.4GHz band and
vice versa TX_PIN_CFG_LNA_PE_G* bits for 5GHz.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Register 66 was causing issues on RT6352 if set to the same value as
in MTK driver. With 1c reg value device was working fine in both HT20
and HT40 modes.
Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Remove band check from rf53xx channel config routine since all chips
using it are single band.
Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Current implementation of RT6352 support provides too high tx power
at least on iPA/eLNA devices. Reduce amplification of variable gain
amplifier by 6dB to match board target power of 17dBm.
Transmited signal strength with this patch is similar to that of
stock firmware or pandorabox firmware. Throughput measured with iperf
improves. Device tested: Xiaomi Miwifi Mini.
Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 145198 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Implement custom rt2800mmio flush routine and change txstatus
routine to read TX_STA_FIFO also in the tasklet.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use different tx status timeouts for normal operation and when flushing.
This increase timeout to 2s for normal operation as when there are bad
radio conditions and frames are reposted many times device can not provide
the status for quite long. With new timeout we can still get valid status
on such bad conditions.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Do not check for tx status timeout everytime we perform txstatus tasklet.
Perform check once per half a second.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In order to reuse usb txdone/txstatus routines for mmio, move them
to common rt2800lib.c file.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Only rt2800 subdriver of rt2x00 implement sta_add() and sta_remove(),
we do not need generic version of those.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
RT5370G has hardware RX antenna diversity like RT5390R.
Based on DPO_RT5572_LinuxSTA_2.6.1.3_20121022.tar.bz2 manufacturer driver:
https://d86o2zu8ugzlg.cloudfront.net/mediatek-craft/drivers/DPO_RT5572_LinuxSTA_2.6.1.3_20121022.tar.bz2
Cc: Stanislaw Gruszka <sgruszka@redhat.com>
Cc: Helmut Schaa <helmut.schaa@googlemail.com>
Cc: Gertjan van Wingerde <gwingerde@gmail.com>
Cc: Jakub Kicinski <jakub.kicinski@netronome.com>
Cc: wireless newbie <wnewbie72@gmail.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: linux wireless ml <linux-wireless@vger.kernel.org>
Signed-off-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch fix a typo in rt2800lib.c
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since commit 41977e86c9 ("rt2x00: add support for MT7620") we do not
initialize TX_PIN_CFG setting. This cause breakage at least on some
RT3573 devices. To fix the problem patch restores previous behaviour
for non MT7620 chips.
Fixes: 41977e86c9 ("rt2x00: add support for MT7620")
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1480829
Reported-and-tested-by: Jussi Eloranta <jussi.eloranta@csun.edu>
Cc: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Don't populate array glrt_table on the stack but make it static.
Makes the object code a smaller by over 670 bytes:
Before:
text data bss dec hex filename
131772 4733 0 136505 21539 rt2800lib.o
After:
text data bss dec hex filename
131043 4789 0 135832 21298 rt2800lib.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a semi-automated conversion to change rt2x00_desc_read to return
the register contents instead of passing them by value, resulting in
much better object code. The majority of the patch was done using:
sed -i 's:\(\<rt2x00_desc_read\>(.*, .*\), &\(.*\));:\2 = \1);:' \
-i 's:\(\<_rt2x00_desc_read\>(.*, .*\), &\(.*\));:\2 = \1);:' \
drivers/net/wireless/ralink/rt2x00/rt*
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This is a semi-automated conversion to change rt2800_eeprom_read to return
the register contents instead of passing them by value, resulting in
much better object code. The majority of the patch was done using:
sed -i 's:\(\<rt2800_eeprom_read\(_from_array\|\)\>(.*, .*\), &\(.*\));:\3 = \1);:'
drivers/net/wireless/ralink/rt2x00/rt2800lib.c
Some manual tweaking was required here to work around the line wraps.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This is a semi-automated conversion to change rt2x00_eeprom_read()
to return the register contents instead of passing them by value,
resulting in much better object code. The majority of the patch
was done using:
sed -i 's:\(\<rt2x00_eeprom_read\>(.*, .*\), &\(.*\));:\2 = \1);:' \
-i 's:= _\(rt2x00_eeprom_read\):= \1:' drivers/net/wireless/ralink/rt2x00/*
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This is a semi-automated conversion to change *_bbp_read()
to return the register contents instead of passing them by value,
resulting in much better object code. The majority of the patch
was done using:
sed -i 's:\(\<rt.*_bbp_read\>(.*, .*\), &\(.*\));:\2 = \1);:' \
-i 's:\(\<rt.*_bbp_dcoc_read\>(.*, .*\), &\(.*\));:\2 = \1);:' \
-i 's:= _\(rt.*_bbp_read\):\1:' drivers/net/wireless/ralink/rt2x00/*
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This is a semi-automated conversion to change rt2800_register_read
to return the register contents instead of passing them by value,
resulting in much better object code. The majority of the patch
was done using:
sed -i 's:\(rt2800_register_read(.*, .*\), &\(.*\));:\2 = \1);:' \
's:\(rt2800_register_read_lock(.*, .*\), &\(.*\));:\2 = \1);:' \
drivers/net/wireless/ralink/rt2x00/rt2800lib.c
The function itself was modified manually along with the one remaining
multi-line caller that was not covered automatically and the indirect
reference.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This is a semi-automated conversion to change rt2x00_rf_read()
to return the register contents instead of passing them by value,
resulting in much better object code. The majority of the patch
was done using:
sed -i 's:\(\<rt2x00_rf_read\>(.*, .*\), &\(.*\));:\2 = \1);:' \
drivers/net/wireless/ralink/rt2x00/rt*
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With CONFIG_KASAN enabled and gcc-7, we get a warning about rather high
stack usage (with a private patch set I have to turn on this warning,
which I intend to get into the next kernel release):
wireless/ralink/rt2x00/rt2800lib.c: In function 'rt2800_bw_filter_calibration':
wireless/ralink/rt2x00/rt2800lib.c:7990:1: error: the frame size of 2144 bytes is larger than 1536 bytes [-Werror=frame-larger-than=]
The problem is that KASAN inserts a redzone around each local variable
that gets passed by reference, and the newly added function has a lot
of them.
This is a semi-automated conversion to change rt2800_rfcsr_read to return
the register contents instead of passing them by value, resulting in
much better object code. The majority of the patch was done using:
sed -i 's:\(rt2800_rfcsr_read(.*, .*\), &\(.*\));:\2 = \1);:' \
-i 's:\(rt2800_rfcsr_read_bank(.*, .*\), &\(.*\));:\2 = \1);:' \
drivers/net/wireless/ralink/rt2x00/rt2800lib.c
Fixes: 41977e86c9 ("rt2x00: add support for MT7620")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This prepares the driver for changing all the 'read' register accessors
to return the value instead of passing it by reference. Since a lot
of them are used in callbacks, this takes care of the callbacks first,
adding a couple of helpers that will be removed again one at a time.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
update RF register 47 and 54 values according to vendor driver
Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use register values from init LNA function instead of the ones from
restore LNA function. Apply register values based on rx path
configuration.
Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Somehow AP doesn't come up and the first scan fails if we don't do
VCO calibration every time.
The vendor driver duplicates the VCO calibration function into the
channel switching logic, we can do the same with less duplication.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The base value used for MT7620 differs from Rt5392 which resulted in
quite bad RX signal quality. Fix this by using the correct base value as
well as the LNA calibration values for HT20.
Reported-by: Tom Psyborg <pozega.tomislav@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Consequently refer to external PA instead of inverting the logic and
use an internal PA capability flag which is a bit confusing.
Currently this is used for Rt3352 only, but MT7620A also allows for an
external PA which will be supported by a follow up patch.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Basic support for MT7620 built-in wireless radio was added to
OpenWrt in r41441. It has seen some heavy cleaning and refactoring
since in order to match the Kernel's code quality standards.
Signed-off-by: Roman Yeryomin <roman@advem.lv>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
