We use skb_desc->tx_rate_flags from entry as rate[].flags even if
skb does not match status. Patch corrects flags and also fixes
mcs for legacy rates.
rt2800_rate_from_status() is based on Felix's mt76
mt76x2_mac_process_tx_rate() function.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If we do not match skb entry, provide tx status via nomatch procedure.
Currently in that case we do rt2x00lib_txdone_noinfo(TXDONE_NOINFO),
which actually assume that entry->skb was posted without retries and
provide rate saved in skb desc as successful. Patch changed that to
rate read from TX_STAT_FIFO, however still do not provide correct
number of retries.
On SoC/PCI devices we keep providing status via standard txdone
procedure, no change in those devices, though we should thing about it.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add framework to identify sta based on tx status WCID. This is currently
not used, will start be utilized in the future patch.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When we restart system using sysrq RT3290 device do not initalize
properly, hance always enable it via WLAN_FUN_CTRL register on
probe.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=85461
Reported-and-tested-by: Giedrius Statkevičius <edrius.statkevicius@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Support for the RT5350 WiSoC was added to OpenWrt after having a
lengthy debate about the legality of the original submission, see
https://lists.openwrt.org/pipermail/openwrt-devel/2013-January/018224.html
MTK/Ralink Acked replied and says we can merge this patch under the GPL.
https://dev.openwrt.org/changeset/36177
Signed-off-by: Serge Vasilugin <vasilugin@yandex.ru>
Tested-by: Michel Stempin <michel.stempin@wanadoo.fr>
Acked-by: John Crispin <blogic@openwrt.org>
[daniel@makrotopia.org: added commit message, cleaned up code]
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
On Rt3352 the driver needs to know the frequency of an external
crystal which can be either 40 MHz (as on all other WiSoCs until now)
or 20 MHz.
Get the clock attached by ramips WiSoC platform code which probes
SYSC_REG_SYSCFG (added by John Crispin in commit 6ac8579b96) and
introduce a new flag clk_is_20mhz in struct hw_mode_spec to make the
driver aware and use either 40 MHz or 20 MHz specific rf_vals on those
WiSoC platforms.
The introduced support for boards with a 20 MHz crystal is also needed
for RT5350.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This is needed for WiFi to work e.g. on DIR-615 rev.H1 which got
external RF power amplifiers connected to the WiSoC.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Simple patch to correct HT20/HT40 filter setting.
Tested with Rt3290, Rt3352 and Rt5350
Signed-off-by: Serge Vasilugin <vasilugin@yandex.ru>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since rt2800pci update beacon settings asynchronously from
tbtt tasklet, without beacon_skb_mutex protection, number of
currently active beacons entries can be different than
number pointed by rt2x00dev->intf_beaconing. Remove warning
about that inconsistency.
Reported-by: evaxige@qq.com
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
All Ralink USB devices I have, including old ones, work well with
max_psdu = 3 (64kB tx AMPDUs).
Fix indent on the way.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Enable RTS frame retry fall-back and limit number of RTS retries to 7
what is default number of retries for small frames. As RTS/CTS is used
for TXOP protection, those settings prevent posting lots of RTS
frames when remote station do not response with CTS at the moment. After
sending 7 RTS's the HW will start back-off mechanism and after it will
start posing RTS again to get access to the medium.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We do not have option to set per frame retry count. We have only global
TX_RTY_CFG registers which specify the number or retries. Set setting
of that register to value that correspond rate control algorithm number
of frame post (number of retries + 1), which is 3 for aggregated frames.
This should help with big amount of retries on bad conditions, hence
mitigate buffer-bloat like problems.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
msleep(1) can sleep much more time then requested 1ms, this is not good
on channel switch, which we want to be performed fast (i.e. to make scan
faster). Replace msleep() with usleep_range(), which has much smaller
maximum sleeping time boundary.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This procedure can sleep, hence mdelay is not needed.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since we reset TX_PIN_CFG register, we have to finish recalibration.
Warn if this is not possible.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We have different modes of adjusting freq offset on different chips.
Call current adjustment similarly like vendor driver - mode1 .
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
MAX_LEN_CFG_MAX_PSDU specify maximum transmitted by HW AMPDU length
(0 - 8kB, 1 - 16kB, 2 - 32kB, 3 - 64kB). Set this option according to
remote stations capabilities (based on HT ampdu_factor). However limit
the value based our hardware TX capabilities as some chips can not send
more than 16kB (factor 1). Limit for all chips is currently 32kB
(factor 2), but perhaps for some chips this could be increased
to 64kB by setting drv_data->max_psdu to 3.
Since MAX_LEN_CFG_MAX_PSDU is global setting, on multi stations modes
(AP, IBSS, mesh) we limit according to less capable remote STA. We can
not set bigger value to speed up communication with some stations and
do not break communication with slow stations.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Initalize max ampdu_factor supported by us based on rx chains, vendor
driver do the same.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Sending frames in CCK rates on HT can cause performance problems.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use RTS/CTS protection for TXOP on all rates modes as default and
disable CCK rates (this cause performance problems).
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Change default to RTS/CTS protection. This has a cost of transmitting
one more control frame (RTS) however protect us from traffic from
hidden node.
On station mode will use CTS-to-self if AP will configure that
for the network.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Those TX_SW_CFG1 values are used in vendor driver.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Initialize AUTO_RSP_CFG register to similar value as vendor driver does.
Do not set BAC_ACK_POLICY based on short preamble setting, those are
unrelated.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We already initlized WPDMA_GLO_CFG_WP_DMA_BURST_SIZE to 3 on
rt2800_init_registers() for USB devices. For PCI devices we will use
HW default setting, which is 2, so patch does not change behaviour
on PCI devices.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We should only set IEEE80211_HT_MCS_TX_RX_DIF when TX and RX MCS sets
are not equal, i.e. when number of tx streams is different than
number of RX streams.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
On some devices the EEPROMs of Ralink Wi-Fi chips have a default Ralink
MAC address set (RT3062F: 00:0C:43:30:62:00, RT3060F:
00:0C:43:30:60:00). Using multiple of these devices in the same network
can cause nasty issues.
Allow to override the MAC in the EEPROM with (a known good) one set in
the device tree to bypass the issue.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If rt2800usb is loaded with nohwcrypt=1, mac80211 takes
care of the crypto with software encryption/decryption
and thus, MFP can be used.
Tested for secured mesh using ath9k_htc and ath9k.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This enum is already perfectly aliased to enum nl80211_band, and
the only reason for it is that we get IEEE80211_NUM_BANDS out of
it. There's no really good reason to not declare the number of
bands in nl80211 though, so do that and remove the cfg80211 one.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since commit df1404650c ("mac80211: remove support for IFF_PROMISC")
monitor mode for rt2x00 has been made effectively useless because the
hardware filter is configured to drop packets whose intended recipient is
not the device, regardless of the presence of monitor mode interfaces.
This patch fixes this regression by adding explicit monitor mode support,
and by configuring the hardware filter accordingly.
Signed-off-by: Eli Cooper <elicooper@gmx.com>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently mac80211 does not inform the driver of the session
block ack timeout when starting a rx aggregation session.
Drivers that manage the reorder buffer need to know this
parameter.
Seeing that there are now too many arguments for the
drv_ampdu_action() function, wrap them inside a structure.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
