In 32-bit architecture, the result of sizeof() is a 32-bit integer so
the expression becomes the multiplication between 2 32-bit integer which
can potentially leads to integer overflow. As a result,
bpf_map_area_alloc() allocates less memory than needed.
Fix this by casting 1 operand to u64.
Fixes: 0d2c4f9640 ("bpf: Eliminate rlimit-based memory accounting for sockmap and sockhash maps")
Fixes: 99c51064fb ("devmap: Use bpf_map_area_alloc() for allocating hash buckets")
Fixes: 546ac1ffb7 ("bpf: add devmap, a map for storing net device references")
Signed-off-by: Bui Quang Minh <minhquangbui99@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20210613143440.71975-1-minhquangbui99@gmail.com
Currently when an unstable clocksource is detected, the raw counters of
that clocksource and watchdog will be printed, which can only be understood
after some math calculation.
So print the delta in nanoseconds as well to make it easier for humans to
check the results.
[ paulmck: Fix typo. ]
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20210527190124.440372-6-paulmck@kernel.org
When the clocksource watchdog marks a clock as unstable, this might
be due to that clock being unstable or it might be due to delays that
happen to occur between the reads of the two clocks. It would be good
to have a way of testing the clocksource watchdog's ability to
distinguish between these two causes of clock skew and instability.
Therefore, provide a new clocksource-wdtest module selected by a new
TEST_CLOCKSOURCE_WATCHDOG Kconfig option. This module has a single module
parameter named "holdoff" that provides the number of seconds of delay
before testing should start, which defaults to zero when built as a module
and to 10 seconds when built directly into the kernel. Very large systems
that boot slowly may need to increase the value of this module parameter.
This module uses hand-crafted clocksource structures to do its testing,
thus avoiding messing up timing for the rest of the kernel and for user
applications. This module first verifies that the ->uncertainty_margin
field of the clocksource structures are set sanely. It then tests the
delay-detection capability of the clocksource watchdog, increasing the
number of consecutive delays injected, first provoking console messages
complaining about the delays and finally forcing a clock-skew event.
Unexpected test results cause at least one WARN_ON_ONCE() console splat.
If there are no splats, the test has passed. Finally, it fuzzes the
value returned from a clocksource to test the clocksource watchdog's
ability to detect time skew.
This module checks the state of its clocksource after each test, and
uses WARN_ON_ONCE() to emit a console splat if there are any failures.
This should enable all types of test frameworks to detect any such
failures.
This facility is intended for diagnostic use only, and should be avoided
on production systems.
Reported-by: Chris Mason <clm@fb.com>
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Feng Tang <feng.tang@intel.com>
Link: https://lore.kernel.org/r/20210527190124.440372-5-paulmck@kernel.org
Currently, WATCHDOG_THRESHOLD is set to detect a 62.5-millisecond skew in
a 500-millisecond WATCHDOG_INTERVAL. This requires that clocks be skewed
by more than 12.5% in order to be marked unstable. Except that a clock
that is skewed by that much is probably destroying unsuspecting software
right and left. And given that there are now checks for false-positive
skews due to delays between reading the two clocks, it should be possible
to greatly decrease WATCHDOG_THRESHOLD, at least for fine-grained clocks
such as TSC.
Therefore, add a new uncertainty_margin field to the clocksource structure
that contains the maximum uncertainty in nanoseconds for the corresponding
clock. This field may be initialized manually, as it is for
clocksource_tsc_early and clocksource_jiffies, which is copied to
refined_jiffies. If the field is not initialized manually, it will be
computed at clock-registry time as the period of the clock in question
based on the scale and freq parameters to __clocksource_update_freq_scale()
function. If either of those two parameters are zero, the
tens-of-milliseconds WATCHDOG_THRESHOLD is used as a cowardly alternative
to dividing by zero. No matter how the uncertainty_margin field is
calculated, it is bounded below by twice WATCHDOG_MAX_SKEW, that is, by 100
microseconds.
Note that manually initialized uncertainty_margin fields are not adjusted,
but there is a WARN_ON_ONCE() that triggers if any such field is less than
twice WATCHDOG_MAX_SKEW. This WARN_ON_ONCE() is intended to discourage
production use of the one-nanosecond uncertainty_margin values that are
used to test the clock-skew code itself.
The actual clock-skew check uses the sum of the uncertainty_margin fields
of the two clocksource structures being compared. Integer overflow is
avoided because the largest computed value of the uncertainty_margin
fields is one billion (10^9), and double that value fits into an
unsigned int. However, if someone manually specifies (say) UINT_MAX,
they will get what they deserve.
Note that the refined_jiffies uncertainty_margin field is initialized to
TICK_NSEC, which means that skew checks involving this clocksource will
be sufficently forgiving. In a similar vein, the clocksource_tsc_early
uncertainty_margin field is initialized to 32*NSEC_PER_MSEC, which
replicates the current behavior and allows custom setting if needed
in order to address the rare skews detected for this clocksource in
current mainline.
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Feng Tang <feng.tang@intel.com>
Link: https://lore.kernel.org/r/20210527190124.440372-4-paulmck@kernel.org
Currently, if skew is detected on a clock marked CLOCK_SOURCE_VERIFY_PERCPU,
that clock is checked on all CPUs. This is thorough, but might not be
what you want on a system with a few tens of CPUs, let alone a few hundred
of them.
Therefore, by default check only up to eight randomly chosen CPUs. Also
provide a new clocksource.verify_n_cpus kernel boot parameter. A value of
-1 says to check all of the CPUs, and a non-negative value says to randomly
select that number of CPUs, without concern about selecting the same CPU
multiple times. However, make use of a cpumask so that a given CPU will be
checked at most once.
Suggested-by: Thomas Gleixner <tglx@linutronix.de> # For verify_n_cpus=1.
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Feng Tang <feng.tang@intel.com>
Link: https://lore.kernel.org/r/20210527190124.440372-3-paulmck@kernel.org
Some sorts of per-CPU clock sources have a history of going out of
synchronization with each other. However, this problem has purportedy been
solved in the past ten years. Except that it is all too possible that the
problem has instead simply been made less likely, which might mean that
some of the occasional "Marking clocksource 'tsc' as unstable" messages
might be due to desynchronization. How would anyone know?
Therefore apply CPU-to-CPU synchronization checking to newly unstable
clocksource that are marked with the new CLOCK_SOURCE_VERIFY_PERCPU flag.
Lists of desynchronized CPUs are printed, with the caveat that if it
is the reporting CPU that is itself desynchronized, it will appear that
all the other clocks are wrong. Just like in real life.
Reported-by: Chris Mason <clm@fb.com>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Feng Tang <feng.tang@intel.com>
Link: https://lore.kernel.org/r/20210527190124.440372-2-paulmck@kernel.org
When the clocksource watchdog marks a clock as unstable, this might be due
to that clock being unstable or it might be due to delays that happen to
occur between the reads of the two clocks. Yes, interrupts are disabled
across those two reads, but there are no shortage of things that can delay
interrupts-disabled regions of code ranging from SMI handlers to vCPU
preemption. It would be good to have some indication as to why the clock
was marked unstable.
Therefore, re-read the watchdog clock on either side of the read from the
clock under test. If the watchdog clock shows an excessive time delta
between its pair of reads, the reads are retried.
The maximum number of retries is specified by a new kernel boot parameter
clocksource.max_cswd_read_retries, which defaults to three, that is, up to
four reads, one initial and up to three retries. If more than one retry
was required, a message is printed on the console (the occasional single
retry is expected behavior, especially in guest OSes). If the maximum
number of retries is exceeded, the clock under test will be marked
unstable. However, the probability of this happening due to various sorts
of delays is quite small. In addition, the reason (clock-read delays) for
the unstable marking will be apparent.
Reported-by: Chris Mason <clm@fb.com>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Feng Tang <feng.tang@intel.com>
Link: https://lore.kernel.org/r/20210527190124.440372-1-paulmck@kernel.org
If there is no matched result, check_redundant() will return BFS_RNOMATCH.
Signed-off-by: Xiongwei Song <sxwjean@gmail.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Boqun Feng <boqun.feng@gmail.com>
Link: https://lkml.kernel.org/r/20210618130230.123249-1-sxwjean@me.com
The FUTEX_LOCK_PI futex operand uses a CLOCK_REALTIME based absolute
timeout since it was implemented, but it does not require that the
FUTEX_CLOCK_REALTIME flag is set, because that was introduced later.
In theory as none of the user space implementations can set the
FUTEX_CLOCK_REALTIME flag on this operand, it would be possible to
creatively abuse it and make the meaning invers, i.e. select CLOCK_REALTIME
when not set and CLOCK_MONOTONIC when set. But that's a nasty hackery.
Another option would be to have a new FUTEX_CLOCK_MONOTONIC flag only for
FUTEX_LOCK_PI, but that's also awkward because it does not allow libraries
to handle the timeout clock selection consistently.
So provide a new FUTEX_LOCK_PI2 operand which implements the timeout
semantics which the other operands use and leave FUTEX_LOCK_PI alone.
Reported-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/20210422194705.440773992@linutronix.de
futex_lock_pi() is the only futex operation which cannot select the clock
for timeouts (CLOCK_MONOTONIC/CLOCK_REALTIME). That's inconsistent and
there is no particular reason why this cannot be supported.
This was overlooked when CLOCK_REALTIME_FLAG was introduced and
unfortunately not reported when the inconsistency was discovered in glibc.
Prepare the function and enforce the CLOCK_REALTIME_FLAG on FUTEX_LOCK_PI
so that a new FUTEX_LOCK_PI2 can implement it correctly.
Reported-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/20210422194705.338657741@linutronix.de
Even the very first lock can violate the wait-context check, consider
the various IRQ contexts.
Fixes: de8f5e4f2d ("lockdep: Introduce wait-type checks")
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Joerg Roedel <jroedel@suse.de>
Link: https://lore.kernel.org/r/20210617190313.256987481@infradead.org
In the step #3 of check_irq_usage(), we seach backwards to find a lock
whose usage conflicts the usage of @target_entry1 on safe/unsafe.
However, we should only keep the irq-unsafe usage of @target_entry1 into
consideration, because it could be a case where a lock is hardirq-unsafe
but soft-safe, and in check_irq_usage() we find it because its
hardirq-unsafe could result into a hardirq-safe-unsafe deadlock, but
currently since we don't filter out the other usage bits, so we may find
a lock dependency path softirq-unsafe -> softirq-safe, which in fact
doesn't cause a deadlock. And this may cause misleading lockdep splats.
Fix this by only keeping LOCKF_ENABLED_IRQ_ALL bits when we try the
backwards search.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Boqun Feng <boqun.feng@gmail.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/20210618170110.3699115-4-boqun.feng@gmail.com
In print_bad_irq_dependency(), save_trace() is called to set the ->trace
for @prev_root as the current call trace, however @prev_root corresponds
to the the held lock, which may not be acquired in current call trace,
therefore it's wrong to use save_trace() to set ->trace of @prev_root.
Moreover, with our adjustment of printing backwards dependency path, the
->trace of @prev_root is unncessary, so remove it.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Boqun Feng <boqun.feng@gmail.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/20210618170110.3699115-3-boqun.feng@gmail.com
We use the same code to print backwards lock dependency path as the
forwards lock dependency path, and this could result into incorrect
printing because for a backwards lock_list ->trace is not the call trace
where the lock of ->class is acquired.
Fix this by introducing a separate function on printing the backwards
dependency path. Also add a few comments about the printing while we are
at it.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Boqun Feng <boqun.feng@gmail.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/20210618170110.3699115-2-boqun.feng@gmail.com
Now cpu.uclamp.min acts as a protection, we need to make sure that the
uclamp request of the task is within the allowed range of the cgroup,
that is it is clamp()'ed correctly by tg->uclamp[UCLAMP_MIN] and
tg->uclamp[UCLAMP_MAX].
As reported by Xuewen [1] we can have some corner cases where there's
inversion between uclamp requested by task (p) and the uclamp values of
the taskgroup it's attached to (tg). Following table demonstrates
2 corner cases:
| p | tg | effective
-----------+-----+------+-----------
CASE 1
-----------+-----+------+-----------
uclamp_min | 60% | 0% | 60%
-----------+-----+------+-----------
uclamp_max | 80% | 50% | 50%
-----------+-----+------+-----------
CASE 2
-----------+-----+------+-----------
uclamp_min | 0% | 30% | 30%
-----------+-----+------+-----------
uclamp_max | 20% | 50% | 20%
-----------+-----+------+-----------
With this fix we get:
| p | tg | effective
-----------+-----+------+-----------
CASE 1
-----------+-----+------+-----------
uclamp_min | 60% | 0% | 50%
-----------+-----+------+-----------
uclamp_max | 80% | 50% | 50%
-----------+-----+------+-----------
CASE 2
-----------+-----+------+-----------
uclamp_min | 0% | 30% | 30%
-----------+-----+------+-----------
uclamp_max | 20% | 50% | 30%
-----------+-----+------+-----------
Additionally uclamp_update_active_tasks() must now unconditionally
update both UCLAMP_MIN/MAX because changing the tg's UCLAMP_MAX for
instance could have an impact on the effective UCLAMP_MIN of the tasks.
| p | tg | effective
-----------+-----+------+-----------
old
-----------+-----+------+-----------
uclamp_min | 60% | 0% | 50%
-----------+-----+------+-----------
uclamp_max | 80% | 50% | 50%
-----------+-----+------+-----------
*new*
-----------+-----+------+-----------
uclamp_min | 60% | 0% | *60%*
-----------+-----+------+-----------
uclamp_max | 80% |*70%* | *70%*
-----------+-----+------+-----------
[1] https://lore.kernel.org/lkml/CAB8ipk_a6VFNjiEnHRHkUMBKbA+qzPQvhtNjJ_YNzQhqV_o8Zw@mail.gmail.com/
Fixes: 0c18f2ecfc ("sched/uclamp: Fix wrong implementation of cpu.uclamp.min")
Reported-by: Xuewen Yan <xuewen.yan94@gmail.com>
Signed-off-by: Qais Yousef <qais.yousef@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20210617165155.3774110-1-qais.yousef@arm.com
DL keeps track of the utilization on a per-rq basis with the structure
avg_dl. This utilization is updated during task_tick_dl(),
put_prev_task_dl() and set_next_task_dl(). However, when the current
running task changes its policy, set_next_task_dl() which would usually
take care of updating the utilization when the rq starts running DL
tasks, will not see a such change, leaving the avg_dl structure outdated.
When that very same task will be dequeued later, put_prev_task_dl() will
then update the utilization, based on a wrong last_update_time, leading to
a huge spike in the DL utilization signal.
The signal would eventually recover from this issue after few ms. Even
if no DL tasks are run, avg_dl is also updated in
__update_blocked_others(). But as the CPU capacity depends partly on the
avg_dl, this issue has nonetheless a significant impact on the scheduler.
Fix this issue by ensuring a load update when a running task changes
its policy to DL.
Fixes: 3727e0e ("sched/dl: Add dl_rq utilization tracking")
Signed-off-by: Vincent Donnefort <vincent.donnefort@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Vincent Guittot <vincent.guittot@linaro.org>
Link: https://lore.kernel.org/r/1624271872-211872-3-git-send-email-vincent.donnefort@arm.com
RT keeps track of the utilization on a per-rq basis with the structure
avg_rt. This utilization is updated during task_tick_rt(),
put_prev_task_rt() and set_next_task_rt(). However, when the current
running task changes its policy, set_next_task_rt() which would usually
take care of updating the utilization when the rq starts running RT tasks,
will not see a such change, leaving the avg_rt structure outdated. When
that very same task will be dequeued later, put_prev_task_rt() will then
update the utilization, based on a wrong last_update_time, leading to a
huge spike in the RT utilization signal.
The signal would eventually recover from this issue after few ms. Even if
no RT tasks are run, avg_rt is also updated in __update_blocked_others().
But as the CPU capacity depends partly on the avg_rt, this issue has
nonetheless a significant impact on the scheduler.
Fix this issue by ensuring a load update when a running task changes
its policy to RT.
Fixes: 371bf427 ("sched/rt: Add rt_rq utilization tracking")
Signed-off-by: Vincent Donnefort <vincent.donnefort@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Vincent Guittot <vincent.guittot@linaro.org>
Link: https://lore.kernel.org/r/1624271872-211872-2-git-send-email-vincent.donnefort@arm.com
syzbot reported a memory leak related to sigqueue caching.
The assumption that a task cannot cache a sigqueue after the signal handler
has been dropped and exit_task_sigqueue_cache() has been invoked turns out
to be wrong.
Such a task can still invoke release_task(other_task), which cleans up the
signals of 'other_task' and ends up in sigqueue_cache_or_free(), which in
turn will cache the signal because task->sigqueue_cache is NULL. That's
obviously bogus because nothing will free the cached signal of that task
anymore, so the cached item is leaked.
This happens when e.g. the last non-leader thread exits and reaps the
zombie leader.
Prevent this by setting tsk::sigqueue_cache to an error pointer value in
exit_task_sigqueue_cache() which forces any subsequent invocation of
sigqueue_cache_or_free() from that task to hand the sigqueue back to the
kmemcache.
Add comments to all relevant places.
Fixes: 4bad58ebc8 ("signal: Allow tasks to cache one sigqueue struct")
Reported-by: syzbot+0bac5fec63d4f399ba98@syzkaller.appspotmail.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Christian Brauner <christian.brauner@ubuntu.com>
Link: https://lore.kernel.org/r/878s32g6j5.ffs@nanos.tec.linutronix.de
This reverts commit d37300ed18 ("bpf: program: Refuse non-O_RDWR flags
in BPF_OBJ_GET"). It breaks Android userspace which expects to be able to
fetch programs with just read permissions.
See: https://cs.android.com/android/platform/superproject/+/master:frameworks/libs/net/common/native/bpf_syscall_wrappers/include/BpfSyscallWrappers.h;drc=7005c764be23d31fa1d69e826b4a2f6689a8c81e;l=124
Side-note: another option to fix it would be to extend bpf_prog_new_fd()
and to pass in used file mode flags in the same way as we do for maps via
bpf_map_new_fd(). Meaning, they'd end up in anon_inode_getfd() and thus
would be retained for prog fd operations with bpf() syscall. Right now
these flags are not checked with progs since they are immutable for their
lifetime (as opposed to maps which can be updated from user space). In
future this could potentially change with new features, but at that point
it's still fine to do the bpf_prog_new_fd() extension when needed. For a
simple stable fix, a revert is less churn.
Fixes: d37300ed18 ("bpf: program: Refuse non-O_RDWR flags in BPF_OBJ_GET")
Signed-off-by: Maciej Żenczykowski <maze@google.com>
[ Daniel: added side-note to commit message ]
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Lorenz Bauer <lmb@cloudflare.com>
Acked-by: Greg Kroah-Hartman <gregkh@google.com>
Link: https://lore.kernel.org/bpf/20210618105526.265003-1-zenczykowski@gmail.com
Ensure that a CFS parent will be in the list whenever one of its children is also
in the list.
A warning on rq->tmp_alone_branch != &rq->leaf_cfs_rq_list has been
reported while running LTP test cfs_bandwidth01.
Odin Ugedal found the root cause:
$ tree /sys/fs/cgroup/ltp/ -d --charset=ascii
/sys/fs/cgroup/ltp/
|-- drain
`-- test-6851
`-- level2
|-- level3a
| |-- worker1
| `-- worker2
`-- level3b
`-- worker3
Timeline (ish):
- worker3 gets throttled
- level3b is decayed, since it has no more load
- level2 get throttled
- worker3 get unthrottled
- level2 get unthrottled
- worker3 is added to list
- level3b is not added to list, since nr_running==0 and is decayed
[ Vincent Guittot: Rebased and updated to fix for the reported warning. ]
Fixes: a7b359fc6a ("sched/fair: Correctly insert cfs_rq's to list on unthrottle")
Reported-by: Sachin Sant <sachinp@linux.vnet.ibm.com>
Suggested-by: Vincent Guittot <vincent.guittot@linaro.org>
Signed-off-by: Rik van Riel <riel@surriel.com>
Signed-off-by: Vincent Guittot <vincent.guittot@linaro.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Tested-by: Sachin Sant <sachinp@linux.vnet.ibm.com>
Acked-by: Odin Ugedal <odin@uged.al>
Link: https://lore.kernel.org/r/20210621174330.11258-1-vincent.guittot@linaro.org
The cpu lock implementation uses a full memory barrier to take
the lock, but no memory barriers when releasing the lock. This
means that changes performed by a lock owner may not be seen by
the next lock owner. This may have been "good enough" for use
by dump_stack() as a serialization mechanism, but it is not
enough to provide proper protection for a critical section.
Correct this problem by using acquire/release memory barriers
for lock/unlock, respectively.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Reviewed-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Link: https://lore.kernel.org/r/20210617095051.4808-3-john.ogness@linutronix.de
dump_stack() implements its own cpu-reentrant spinning lock to
best-effort serialize stack traces in the printk log. However,
there are other functions (such as show_regs()) that can also
benefit from this serialization.
Move the cpu-reentrant spinning lock (cpu lock) into new helper
functions printk_cpu_lock_irqsave()/printk_cpu_unlock_irqrestore()
so that it is available for others as well. For !CONFIG_SMP the
cpu lock is a NOP.
Note that having multiple cpu locks in the system can easily
lead to deadlock. Code needing a cpu lock should use the
printk cpu lock, since the printk cpu lock could be acquired
from any code and any context.
Also note that it is not necessary for a cpu lock to disable
interrupts. However, in upcoming work this cpu lock will be used
for emergency tasks (for example, atomic consoles during kernel
crashes) and any interruptions while holding the cpu lock should
be avoided if possible.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Reviewed-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Reviewed-by: Petr Mladek <pmladek@suse.com>
[pmladek@suse.com: Backported on top of 5.13-rc1.]
Signed-off-by: Petr Mladek <pmladek@suse.com>
Link: https://lore.kernel.org/r/20210617095051.4808-2-john.ogness@linutronix.de
Since, overlapping mappings are not supported by the DMA API we should
report an error if active_cacheline_insert returns -EEXIST.
Suggested-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Hamza Mahfooz <someguy@effective-light.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
in case of driver wants to sync part of ranges with offset,
swiotlb_tbl_sync_single() copies from orig_addr base to tlb_addr with
offset and ends up with data mismatch.
It was removed from
"swiotlb: don't modify orig_addr in swiotlb_tbl_sync_single",
but said logic has to be added back in.
From Linus's email:
"That commit which the removed the offset calculation entirely, because the old
(unsigned long)tlb_addr & (IO_TLB_SIZE - 1)
was wrong, but instead of removing it, I think it should have just
fixed it to be
(tlb_addr - mem->start) & (IO_TLB_SIZE - 1);
instead. That way the slot offset always matches the slot index calculation."
(Unfortunatly that broke NVMe).
The use-case that drivers are hitting is as follow:
1. Get dma_addr_t from dma_map_single()
dma_addr_t tlb_addr = dma_map_single(dev, vaddr, vsize, DMA_TO_DEVICE);
|<---------------vsize------------->|
+-----------------------------------+
| | original buffer
+-----------------------------------+
vaddr
swiotlb_align_offset
|<----->|<---------------vsize------------->|
+-------+-----------------------------------+
| | | swiotlb buffer
+-------+-----------------------------------+
tlb_addr
2. Do something
3. Sync dma_addr_t through dma_sync_single_for_device(..)
dma_sync_single_for_device(dev, tlb_addr + offset, size, DMA_TO_DEVICE);
Error case.
Copy data to original buffer but it is from base addr (instead of
base addr + offset) in original buffer:
swiotlb_align_offset
|<----->|<- offset ->|<- size ->|
+-------+-----------------------------------+
| | |##########| | swiotlb buffer
+-------+-----------------------------------+
tlb_addr
|<- size ->|
+-----------------------------------+
|##########| | original buffer
+-----------------------------------+
vaddr
The fix is to copy the data to the original buffer and take into
account the offset, like so:
swiotlb_align_offset
|<----->|<- offset ->|<- size ->|
+-------+-----------------------------------+
| | |##########| | swiotlb buffer
+-------+-----------------------------------+
tlb_addr
|<- offset ->|<- size ->|
+-----------------------------------+
| |##########| | original buffer
+-----------------------------------+
vaddr
[One fix which was Linus's that made more sense to as it created a
symmetry would break NVMe. The reason for that is the:
unsigned int offset = (tlb_addr - mem->start) & (IO_TLB_SIZE - 1);
would come up with the proper offset, but it would lose the
alignment (which this patch contains).]
Fixes: 16fc3cef33 ("swiotlb: don't modify orig_addr in swiotlb_tbl_sync_single")
Signed-off-by: Bumyong Lee <bumyong.lee@samsung.com>
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reported-by: Dominique MARTINET <dominique.martinet@atmark-techno.com>
Reported-by: Horia Geantă <horia.geanta@nxp.com>
Tested-by: Horia Geantă <horia.geanta@nxp.com>
CC: stable@vger.kernel.org
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
There can be few cases when we need to shut-down the system in order to
protect the hardware. Currently this is done at least by the thermal core
when temperature raises over certain limit.
Some PMICs can also generate interrupts for example for over-current or
over-voltage, voltage drops, short-circuit, ... etc. On some systems
these are a sign of hardware failure and only thing to do is try to
protect the rest of the hardware by shutting down the system.
Add shut-down logic which can be used by all subsystems instead of
implementing the shutdown in each subsystem. The logic is stolen from
thermal_core with difference of using atomic_t instead of a mutex in
order to allow calls directly from IRQ context and changing the WARN()
to pr_emerg() as discussed here:
https://lore.kernel.org/lkml/YJuPwAZroVZ%2Fw633@alley/
and here:
https://lore.kernel.org/linux-iommu/20210331093104.383705-4-geert+renesas@glider.be/
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/e83ec1ca9408f90c857ea9dcdc57b14d9037b03f.1622628333.git.matti.vaittinen@fi.rohmeurope.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Alexey and Joshua tried to solve a cpusets related hotplug problem which is
user space visible and results in unexpected behaviour for some time after
a CPU has been plugged in and the corresponding uevent was delivered.
cpusets delegate the hotplug work (rebuilding cpumasks etc.) to a
workqueue. This is done because the cpusets code has already a lock
nesting of cgroups_mutex -> cpu_hotplug_lock. A synchronous callback or
waiting for the work to finish with cpu_hotplug_lock held can and will
deadlock because that results in the reverse lock order.
As a consequence the uevent can be delivered before cpusets have consistent
state which means that a user space invocation of sched_setaffinity() to
move a task to the plugged CPU fails up to the point where the scheduled
work has been processed.
The same is true for CPU unplug, but that does not create user observable
failure (yet).
It's still inconsistent to claim that an operation is finished before it
actually is and that's the real issue at hand. uevents just make it
reliably observable.
Obviously the problem should be fixed in cpusets/cgroups, but untangling
that is pretty much impossible because according to the changelog of the
commit which introduced this 8 years ago:
3a5a6d0c2b03("cpuset: don't nest cgroup_mutex inside get_online_cpus()")
the lock order cgroups_mutex -> cpu_hotplug_lock is a design decision and
the whole code is built around that.
So bite the bullet and invoke the relevant cpuset function, which waits for
the work to finish, in _cpu_up/down() after dropping cpu_hotplug_lock and
only when tasks are not frozen by suspend/hibernate because that would
obviously wait forever.
Waiting there with cpu_add_remove_lock, which is protecting the present
and possible CPU maps, held is not a problem at all because neither work
queues nor cpusets/cgroups have any lockchains related to that lock.
Waiting in the hotplug machinery is not problematic either because there
are already state callbacks which wait for hardware queues to drain. It
makes the operations slightly slower, but hotplug is slow anyway.
This ensures that state is consistent before returning from a hotplug
up/down operation. It's still inconsistent during the operation, but that's
a different story.
Add a large comment which explains why this is done and why this is not a
dump ground for the hack of the day to work around half thought out locking
schemes. Document also the implications vs. hotplug operations and
serialization or the lack of it.
Thanks to Alexy and Joshua for analyzing why this temporary
sched_setaffinity() failure happened.
Fixes: 3a5a6d0c2b03("cpuset: don't nest cgroup_mutex inside get_online_cpus()")
Reported-by: Alexey Klimov <aklimov@redhat.com>
Reported-by: Joshua Baker <jobaker@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Alexey Klimov <aklimov@redhat.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/87tuowcnv3.ffs@nanos.tec.linutronix.de
-----BEGIN PGP SIGNATURE-----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=KnMk
-----END PGP SIGNATURE-----
Merge tag 'sched_urgent_for_v5.13_rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fix from Borislav Petkov:
"A single fix to restore fairness between control groups with equal
priority"
* tag 'sched_urgent_for_v5.13_rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/fair: Correctly insert cfs_rq's to list on unthrottle
Trivial conflicts in net/can/isotp.c and
tools/testing/selftests/net/mptcp/mptcp_connect.sh
scaled_ppm_to_ppb() was moved from drivers/ptp/ptp_clock.c
to include/linux/ptp_clock_kernel.h in -next so re-apply
the fix there.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
bluetooth, netfilter and can.
Current release - regressions:
- mlxsw: spectrum_qdisc: Pass handle, not band number to find_class()
to fix modifying offloaded qdiscs
- lantiq: net: fix duplicated skb in rx descriptor ring
- rtnetlink: fix regression in bridge VLAN configuration, empty info
is not an error, bot-generated "fix" was not needed
- libbpf: s/rx/tx/ typo on umem->rx_ring_setup_done to fix
umem creation
Current release - new code bugs:
- ethtool: fix NULL pointer dereference during module EEPROM dump via
the new netlink API
- mlx5e: don't update netdev RQs with PTP-RQ, the special purpose queue
should not be visible to the stack
- mlx5e: select special PTP queue only for SKBTX_HW_TSTAMP skbs
- mlx5e: verify dev is present in get devlink port ndo, avoid a panic
Previous releases - regressions:
- neighbour: allow NUD_NOARP entries to be force GCed
- further fixes for fallout from reorg of WiFi locking
(staging: rtl8723bs, mac80211, cfg80211)
- skbuff: fix incorrect msg_zerocopy copy notifications
- mac80211: fix NULL ptr deref for injected rate info
- Revert "net/mlx5: Arm only EQs with EQEs" it may cause missed IRQs
Previous releases - always broken:
- bpf: more speculative execution fixes
- netfilter: nft_fib_ipv6: skip ipv6 packets from any to link-local
- udp: fix race between close() and udp_abort() resulting in a panic
- fix out of bounds when parsing TCP options before packets
are validated (in netfilter: synproxy, tc: sch_cake and mptcp)
- mptcp: improve operation under memory pressure, add missing wake-ups
- mptcp: fix double-lock/soft lookup in subflow_error_report()
- bridge: fix races (null pointer deref and UAF) in vlan tunnel egress
- ena: fix DMA mapping function issues in XDP
- rds: fix memory leak in rds_recvmsg
Misc:
- vrf: allow larger MTUs
- icmp: don't send out ICMP messages with a source address of 0.0.0.0
- cdc_ncm: switch to eth%d interface naming
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=xxUe
-----END PGP SIGNATURE-----
Merge tag 'net-5.13-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Networking fixes for 5.13-rc7, including fixes from wireless, bpf,
bluetooth, netfilter and can.
Current release - regressions:
- mlxsw: spectrum_qdisc: Pass handle, not band number to find_class()
to fix modifying offloaded qdiscs
- lantiq: net: fix duplicated skb in rx descriptor ring
- rtnetlink: fix regression in bridge VLAN configuration, empty info
is not an error, bot-generated "fix" was not needed
- libbpf: s/rx/tx/ typo on umem->rx_ring_setup_done to fix umem
creation
Current release - new code bugs:
- ethtool: fix NULL pointer dereference during module EEPROM dump via
the new netlink API
- mlx5e: don't update netdev RQs with PTP-RQ, the special purpose
queue should not be visible to the stack
- mlx5e: select special PTP queue only for SKBTX_HW_TSTAMP skbs
- mlx5e: verify dev is present in get devlink port ndo, avoid a panic
Previous releases - regressions:
- neighbour: allow NUD_NOARP entries to be force GCed
- further fixes for fallout from reorg of WiFi locking (staging:
rtl8723bs, mac80211, cfg80211)
- skbuff: fix incorrect msg_zerocopy copy notifications
- mac80211: fix NULL ptr deref for injected rate info
- Revert "net/mlx5: Arm only EQs with EQEs" it may cause missed IRQs
Previous releases - always broken:
- bpf: more speculative execution fixes
- netfilter: nft_fib_ipv6: skip ipv6 packets from any to link-local
- udp: fix race between close() and udp_abort() resulting in a panic
- fix out of bounds when parsing TCP options before packets are
validated (in netfilter: synproxy, tc: sch_cake and mptcp)
- mptcp: improve operation under memory pressure, add missing
wake-ups
- mptcp: fix double-lock/soft lookup in subflow_error_report()
- bridge: fix races (null pointer deref and UAF) in vlan tunnel
egress
- ena: fix DMA mapping function issues in XDP
- rds: fix memory leak in rds_recvmsg
Misc:
- vrf: allow larger MTUs
- icmp: don't send out ICMP messages with a source address of 0.0.0.0
- cdc_ncm: switch to eth%d interface naming"
* tag 'net-5.13-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (139 commits)
net: ethernet: fix potential use-after-free in ec_bhf_remove
selftests/net: Add icmp.sh for testing ICMP dummy address responses
icmp: don't send out ICMP messages with a source address of 0.0.0.0
net: ll_temac: Avoid ndo_start_xmit returning NETDEV_TX_BUSY
net: ll_temac: Fix TX BD buffer overwrite
net: ll_temac: Add memory-barriers for TX BD access
net: ll_temac: Make sure to free skb when it is completely used
MAINTAINERS: add Guvenc as SMC maintainer
bnxt_en: Call bnxt_ethtool_free() in bnxt_init_one() error path
bnxt_en: Fix TQM fastpath ring backing store computation
bnxt_en: Rediscover PHY capabilities after firmware reset
cxgb4: fix wrong shift.
mac80211: handle various extensible elements correctly
mac80211: reset profile_periodicity/ema_ap
cfg80211: avoid double free of PMSR request
cfg80211: make certificate generation more robust
mac80211: minstrel_ht: fix sample time check
net: qed: Fix memcpy() overflow of qed_dcbx_params()
net: cdc_eem: fix tx fixup skb leak
net: hamradio: fix memory leak in mkiss_close
...
- Have recordmcount check for valid st_shndx otherwise some archs may have
invalid references for the mcount location.
- Two fixes done for mapping pids to task names. Traces were not showing
the names of tasks when they should have.
- Fix to trace_clock_global() to prevent it from going backwards
-----BEGIN PGP SIGNATURE-----
iIoEABYIADIWIQRRSw7ePDh/lE+zeZMp5XQQmuv6qgUCYMyrQBQccm9zdGVkdEBn
b29kbWlzLm9yZwAKCRAp5XQQmuv6qmMvAP4/teh5R2Z1ms0S0JlUM6sS3miNP1t/
x2QQtk2xuzbgmwD/Vn+01//7VyRPGuFm9dD82vSizQiNrns0EHXHB2cEPAQ=
=UWEU
-----END PGP SIGNATURE-----
Merge tag 'trace-v5.13-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fixes from Steven Rostedt:
- Have recordmcount check for valid st_shndx otherwise some archs may
have invalid references for the mcount location.
- Two fixes done for mapping pids to task names. Traces were not
showing the names of tasks when they should have.
- Fix to trace_clock_global() to prevent it from going backwards
* tag 'trace-v5.13-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Do no increment trace_clock_global() by one
tracing: Do not stop recording comms if the trace file is being read
tracing: Do not stop recording cmdlines when tracing is off
recordmcount: Correct st_shndx handling
Remove recently added frequency invariance support from the CPPC
cpufreq driver, because it has turned out to be problematic and it
cannot be fixed properly on time for 5.13 (Viresh Kumar).
-----BEGIN PGP SIGNATURE-----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=tW38
-----END PGP SIGNATURE-----
Merge tag 'pm-5.13-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fix from Rafael Wysocki:
"Remove recently added frequency invariance support from the CPPC
cpufreq driver, because it has turned out to be problematic and it
cannot be fixed properly on time for 5.13 (Viresh Kumar)"
* tag 'pm-5.13-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
Revert "cpufreq: CPPC: Add support for frequency invariance"
The trace_clock_global() tries to make sure the events between CPUs is
somewhat in order. A global value is used and updated by the latest read
of a clock. If one CPU is ahead by a little, and is read by another CPU, a
lock is taken, and if the timestamp of the other CPU is behind, it will
simply use the other CPUs timestamp.
The lock is also only taken with a "trylock" due to tracing, and strange
recursions can happen. The lock is not taken at all in NMI context.
In the case where the lock is not able to be taken, the non synced
timestamp is returned. But it will not be less than the saved global
timestamp.
The problem arises because when the time goes "backwards" the time
returned is the saved timestamp plus 1. If the lock is not taken, and the
plus one to the timestamp is returned, there's a small race that can cause
the time to go backwards!
CPU0 CPU1
---- ----
trace_clock_global() {
ts = clock() [ 1000 ]
trylock(clock_lock) [ success ]
global_ts = ts; [ 1000 ]
<interrupted by NMI>
trace_clock_global() {
ts = clock() [ 999 ]
if (ts < global_ts)
ts = global_ts + 1 [ 1001 ]
trylock(clock_lock) [ fail ]
return ts [ 1001]
}
unlock(clock_lock);
return ts; [ 1000 ]
}
trace_clock_global() {
ts = clock() [ 1000 ]
if (ts < global_ts) [ false 1000 == 1000 ]
trylock(clock_lock) [ success ]
global_ts = ts; [ 1000 ]
unlock(clock_lock)
return ts; [ 1000 ]
}
The above case shows to reads of trace_clock_global() on the same CPU, but
the second read returns one less than the first read. That is, time when
backwards, and this is not what is allowed by trace_clock_global().
This was triggered by heavy tracing and the ring buffer checker that tests
for the clock going backwards:
Ring buffer clock went backwards: 20613921464 -> 20613921463
------------[ cut here ]------------
WARNING: CPU: 2 PID: 0 at kernel/trace/ring_buffer.c:3412 check_buffer+0x1b9/0x1c0
Modules linked in:
[..]
[CPU: 2]TIME DOES NOT MATCH expected:20620711698 actual:20620711697 delta:6790234 before:20613921463 after:20613921463
[20613915818] PAGE TIME STAMP
[20613915818] delta:0
[20613915819] delta:1
[20613916035] delta:216
[20613916465] delta:430
[20613916575] delta:110
[20613916749] delta:174
[20613917248] delta:499
[20613917333] delta:85
[20613917775] delta:442
[20613917921] delta:146
[20613918321] delta:400
[20613918568] delta:247
[20613918768] delta:200
[20613919306] delta:538
[20613919353] delta:47
[20613919980] delta:627
[20613920296] delta:316
[20613920571] delta:275
[20613920862] delta:291
[20613921152] delta:290
[20613921464] delta:312
[20613921464] delta:0 TIME EXTEND
[20613921464] delta:0
This happened more than once, and always for an off by one result. It also
started happening after commit aafe104aa9 was added.
Cc: stable@vger.kernel.org
Fixes: aafe104aa9 ("tracing: Restructure trace_clock_global() to never block")
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
A while ago, when the "trace" file was opened, tracing was stopped, and
code was added to stop recording the comms to saved_cmdlines, for mapping
of the pids to the task name.
Code has been added that only records the comm if a trace event occurred,
and there's no reason to not trace it if the trace file is opened.
Cc: stable@vger.kernel.org
Fixes: 7ffbd48d5c ("tracing: Cache comms only after an event occurred")
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
The saved_cmdlines is used to map pids to the task name, such that the
output of the tracing does not just show pids, but also gives a human
readable name for the task.
If the name is not mapped, the output looks like this:
<...>-1316 [005] ...2 132.044039: ...
Instead of this:
gnome-shell-1316 [005] ...2 132.044039: ...
The names are updated when tracing is running, but are skipped if tracing
is stopped. Unfortunately, this stops the recording of the names if the
top level tracer is stopped, and not if there's other tracers active.
The recording of a name only happens when a new event is written into a
ring buffer, so there is no need to test if tracing is on or not. If
tracing is off, then no event is written and no need to test if tracing is
off or not.
Remove the check, as it hides the names of tasks for events in the
instance buffers.
Cc: stable@vger.kernel.org
Fixes: 7ffbd48d5c ("tracing: Cache comms only after an event occurred")
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Change the type and name of task_struct::state. Drop the volatile and
shrink it to an 'unsigned int'. Rename it in order to find all uses
such that we can use READ_ONCE/WRITE_ONCE as appropriate.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Daniel Bristot de Oliveira <bristot@redhat.com>
Acked-by: Will Deacon <will@kernel.org>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Link: https://lore.kernel.org/r/20210611082838.550736351@infradead.org
There's an existing helper for setting TASK_RUNNING; must've gotten
lost last time we did this cleanup.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Davidlohr Bueso <dbueso@suse.de>
Acked-by: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20210611082838.409696194@infradead.org
When ran from the sched-out path (preempt_notifier or perf_event),
p->state is irrelevant to determine preemption. You can get preempted
with !task_is_running() just fine.
The right indicator for preemption is if the task is still on the
runqueue in the sched-out path.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Link: https://lore.kernel.org/r/20210611082838.285099381@infradead.org
Replace a bunch of 'p->state == TASK_RUNNING' with a new helper:
task_is_running(p).
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Davidlohr Bueso <dave@stgolabs.net>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20210611082838.222401495@infradead.org
Remove broken task->state references and let wake_up_process() DTRT.
The anti-pattern in these patches breaks the ordering of ->state vs
COND as described in the comment near set_current_state() and can lead
to missed wakeups:
(OoO load, observes RUNNING)<-.
for (;;) { |
t->state = UNINTERRUPTIBLE; |
smp_mb(); ,-----> | (observes !COND)
| /
if (COND) ---------' | COND = 1;
break; `- if (t->state != RUNNING)
wake_up_process(t); // not done
schedule(); // forever waiting
}
t->state = TASK_RUNNING;
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Davidlohr Bueso <dbueso@suse.de>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20210611082838.160855222@infradead.org
This commit in sched/urgent moved the cfs_rq_is_decayed() function:
a7b359fc6a: ("sched/fair: Correctly insert cfs_rq's to list on unthrottle")
and this fresh commit in sched/core modified it in the old location:
9e077b52d8: ("sched/pelt: Check that *_avg are null when *_sum are")
Merge the two variants.
Conflicts:
kernel/sched/fair.c
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The kernel parameter for ftrace_dump_on_oops can take a single assignment.
That is, it can be:
ftrace_dump_on_oops or ftrace_dump_on_oops=orig_cpu
But the content in the sysctl file is a number.
0 for disabled
1 for ftrace_dump_on_oops (all CPUs)
2 for ftrace_dump_on_oops (orig CPU)
Allow the kernel command line to take a number as well to match the sysctl
numbers.
That is:
ftrace_dump_on_oops=1 is the same as ftrace_dump_on_oops
and
ftrace_dump_on_oops=2 is the same as ftrace_dump_on_oops=orig_cpu
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Daniel Borkmann says:
====================
pull-request: bpf-next 2021-06-17
The following pull-request contains BPF updates for your *net-next* tree.
We've added 50 non-merge commits during the last 25 day(s) which contain
a total of 148 files changed, 4779 insertions(+), 1248 deletions(-).
The main changes are:
1) BPF infrastructure to migrate TCP child sockets from a listener to another
in the same reuseport group/map, from Kuniyuki Iwashima.
2) Add a provably sound, faster and more precise algorithm for tnum_mul() as
noted in https://arxiv.org/abs/2105.05398, from Harishankar Vishwanathan.
3) Streamline error reporting changes in libbpf as planned out in the
'libbpf: the road to v1.0' effort, from Andrii Nakryiko.
4) Add broadcast support to xdp_redirect_map(), from Hangbin Liu.
5) Extends bpf_map_lookup_and_delete_elem() functionality to 4 more map
types, that is, {LRU_,PERCPU_,LRU_PERCPU_,}HASH, from Denis Salopek.
6) Support new LLVM relocations in libbpf to make them more linker friendly,
also add a doc to describe the BPF backend relocations, from Yonghong Song.
7) Silence long standing KUBSAN complaints on register-based shifts in
interpreter, from Daniel Borkmann and Eric Biggers.
8) Add dummy PT_REGS macros in libbpf to fail BPF program compilation when
target arch cannot be determined, from Lorenz Bauer.
9) Extend AF_XDP to support large umems with 1M+ pages, from Magnus Karlsson.
10) Fix two minor libbpf tc BPF API issues, from Kumar Kartikeya Dwivedi.
11) Move libbpf BPF_SEQ_PRINTF/BPF_SNPRINTF macros that can be used by BPF
programs to bpf_helpers.h header, from Florent Revest.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a kernel command line option that disables printing of events to
console at late_initcall_sync(). This is useful when needing to see
specific events written to console on boot up, but not wanting it when
user space starts, as user space may make the console so noisy that the
system becomes inoperable.
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
This is a partial forward-port of Peter Ziljstra's work first posted
at:
https://lore.kernel.org/lkml/20180530142236.667774973@infradead.org/
Currently select_idle_cpu()'s proportional scheme uses the average idle
time *for when we are idle*, that is temporally challenged. When a CPU
is not at all idle, we'll happily continue using whatever value we did
see when the CPU goes idle. To fix this, introduce a separate average
idle and age it (the existing value still makes sense for things like
new-idle balancing, which happens when we do go idle).
The overall goal is to not spend more time scanning for idle CPUs than
we're idle for. Otherwise we're inhibiting work. This means that we need to
consider the cost over all the wake-ups between consecutive idle periods.
To track this, the scan cost is subtracted from the estimated average
idle time.
The impact of this patch is related to workloads that have domains that
are fully busy or overloaded. Without the patch, the scan depth may be
too high because a CPU is not reaching idle.
Due to the nature of the patch, this is a regression magnet. It
potentially wins when domains are almost fully busy or overloaded --
at that point searches are likely to fail but idle is not being aged
as CPUs are active so search depth is too large and useless. It will
potentially show regressions when there are idle CPUs and a deep search is
beneficial. This tbench result on a 2-socket broadwell machine partially
illustates the problem
5.13.0-rc2 5.13.0-rc2
vanilla sched-avgidle-v1r5
Hmean 1 445.02 ( 0.00%) 451.36 * 1.42%*
Hmean 2 830.69 ( 0.00%) 846.03 * 1.85%*
Hmean 4 1350.80 ( 0.00%) 1505.56 * 11.46%*
Hmean 8 2888.88 ( 0.00%) 2586.40 * -10.47%*
Hmean 16 5248.18 ( 0.00%) 5305.26 * 1.09%*
Hmean 32 8914.03 ( 0.00%) 9191.35 * 3.11%*
Hmean 64 10663.10 ( 0.00%) 10192.65 * -4.41%*
Hmean 128 18043.89 ( 0.00%) 18478.92 * 2.41%*
Hmean 256 16530.89 ( 0.00%) 17637.16 * 6.69%*
Hmean 320 16451.13 ( 0.00%) 17270.97 * 4.98%*
Note that 8 was a regression point where a deeper search would have helped
but it gains for high thread counts when searches are useless. Hackbench
is a more extreme example although not perfect as the tasks idle rapidly
hackbench-process-pipes
5.13.0-rc2 5.13.0-rc2
vanilla sched-avgidle-v1r5
Amean 1 0.3950 ( 0.00%) 0.3887 ( 1.60%)
Amean 4 0.9450 ( 0.00%) 0.9677 ( -2.40%)
Amean 7 1.4737 ( 0.00%) 1.4890 ( -1.04%)
Amean 12 2.3507 ( 0.00%) 2.3360 * 0.62%*
Amean 21 4.0807 ( 0.00%) 4.0993 * -0.46%*
Amean 30 5.6820 ( 0.00%) 5.7510 * -1.21%*
Amean 48 8.7913 ( 0.00%) 8.7383 ( 0.60%)
Amean 79 14.3880 ( 0.00%) 13.9343 * 3.15%*
Amean 110 21.2233 ( 0.00%) 19.4263 * 8.47%*
Amean 141 28.2930 ( 0.00%) 25.1003 * 11.28%*
Amean 172 34.7570 ( 0.00%) 30.7527 * 11.52%*
Amean 203 41.0083 ( 0.00%) 36.4267 * 11.17%*
Amean 234 47.7133 ( 0.00%) 42.0623 * 11.84%*
Amean 265 53.0353 ( 0.00%) 47.7720 * 9.92%*
Amean 296 60.0170 ( 0.00%) 53.4273 * 10.98%*
Stddev 1 0.0052 ( 0.00%) 0.0025 ( 51.57%)
Stddev 4 0.0357 ( 0.00%) 0.0370 ( -3.75%)
Stddev 7 0.0190 ( 0.00%) 0.0298 ( -56.64%)
Stddev 12 0.0064 ( 0.00%) 0.0095 ( -48.38%)
Stddev 21 0.0065 ( 0.00%) 0.0097 ( -49.28%)
Stddev 30 0.0185 ( 0.00%) 0.0295 ( -59.54%)
Stddev 48 0.0559 ( 0.00%) 0.0168 ( 69.92%)
Stddev 79 0.1559 ( 0.00%) 0.0278 ( 82.17%)
Stddev 110 1.1728 ( 0.00%) 0.0532 ( 95.47%)
Stddev 141 0.7867 ( 0.00%) 0.0968 ( 87.69%)
Stddev 172 1.0255 ( 0.00%) 0.0420 ( 95.91%)
Stddev 203 0.8106 ( 0.00%) 0.1384 ( 82.92%)
Stddev 234 1.1949 ( 0.00%) 0.1328 ( 88.89%)
Stddev 265 0.9231 ( 0.00%) 0.0820 ( 91.11%)
Stddev 296 1.0456 ( 0.00%) 0.1327 ( 87.31%)
Again, higher thread counts benefit and the standard deviation
shows that results are also a lot more stable when the idle
time is aged.
The patch potentially matters when a socket was multiple LLCs as the
maximum search depth is lower. However, some of the test results were
suspiciously good (e.g. specjbb2005 gaining 50% on a Zen1 machine) and
other results were not dramatically different to other mcahines.
Given the nature of the patch, Peter's full series is not being forward
ported as each part should stand on its own. Preferably they would be
merged at different times to reduce the risk of false bisections.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20210615111611.GH30378@techsingularity.net
