When AP goes down or too far away without indication to STA, beacon miss
will be detected. Then for WCN7850's firmware, it will use roam event
to send beacon miss to host.
If STA doesn't handle the beacon miss, will keep the fake connection
and unable to roam.
So add support for WCN7850 to trigger disconnection from AP when
receiving this event from firmware.
It has to be noted that beacon miss event notification for QCN9274
to be handled in a separate patch as it uses STA kickout WMI event
to notify beacon miss and the current STA kickout event is processed
as low_ack.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Kang Yang <quic_kangyang@quicinc.com>
Reviewed-by: Nicolas Escande <nico.escande@gmail.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240412094447.2063-1-quic_kangyang@quicinc.com
In order to enable ACPI SAR (Specific Absorption Rate), ath12k gets SAR and GEO
offset tables from ACPI and sends the data to firmware using
WMI_PDEV_SET_BIOS_SAR_TABLE_CMDID and WMI_PDEV_SET_BIOS_GEO_TABLE_CMDID
commands.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Lingbo Kong <quic_lingbok@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240422033054.979-3-quic_lingbok@quicinc.com
Currently, ath12k does not support Time-Average-SAR (TAS). In order to enable
TAS read the tables from ACPI and send them to the firmware using
WMI_PDEV_SET_BIOS_INTERFACE_CMDID command. Besides, ath12k registers an ACPI
event callback so that ACPI can notify ath12k to get the updated SAR power
table and sends it to the firmware when the device state is changed.
ACPI is only enabled for WCN7850 using struct ath12k_hw_params::acpi_guid
field. Most likely QCN9274 will never support ACPI as the chip is not used in
laptops.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Lingbo Kong <quic_lingbok@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240422033054.979-2-quic_lingbok@quicinc.com
We are seeing below warning in both reset and suspend/resume scenarios:
[ 4153.776040] ath12k_pci 0000:04:00.0: Already processed, so ignoring dma ring caps
This is because ab->num_db_cap is not cleared in
ath12k_wmi_free_dbring_caps(), so clear it to avoid such
warnings.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240412060620.27519-5-quic_bqiang@quicinc.com
Currently, when debug logs are enabled, messages such as the following
are found in the kernel log:
event mgmt rx skb pK-error len 209 ftype 00 stype 50
The "pK-error" comes from using %pK to display an skb address in an
interrupt context.
Per the guidance in the current "printk-formats" documentation, %pK
"is only intended when producing content of a file read by userspace
from e.g. procfs or sysfs, not for dmesg."
So replace %pK with %p in all of the ath12k_dbg() format strings.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240416-pk-v1-1-2c8852743e6d@quicinc.com
The survey dump statistics does not display channel RX and TX time
properly because the survey flag is not enabled in the firmware service
flag.
If firmware supports enable the service flag "bss_chan_info" in
wmi_resource_config to fetch and print the stats for specific pdev.
Enabling WMI_RSRC_CFG_FLAG1_BSS_CHANNEL_INFO_64 does not have any impact
on WCN7850 since this bit is not utilized by the WCN7850 firmware.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Thiraviyam Mariyappan <quic_tmariyap@quicinc.com>
Signed-off-by: Karthikeyan Kathirvel <quic_kathirve@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240410085329.3649572-1-quic_kathirve@quicinc.com
The WMI commands are in little endian byte order, fix missing endianness
conversion in wmi_vdev_create_cmd.
Tested-on: WCN7850 hw2.0 WLAN.IOE_HMT.1.0.2-00240-QCAHMTSWPL_V1.0_V2.0_SILICON-1
Signed-off-by: Miaoqing Pan <quic_miaoqing@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240322003726.2016208-1-quic_miaoqing@quicinc.com
Due to an error during rebasing the patchset 320 MHz channel support got
broken. ath12k was setting the QoS bit instead of the correct flag.
WMI_PEER_EXT_320MHZ (0x2) is defined as an extended flag, replace
peer_flags by peer_flags_ext while sending peer data.
This affected both QCN9274 and WCN7850 which use the same flag.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Fixes: 6734cf9b4c ("wifi: ath12k: peer assoc for 320 MHz")
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240314204651.11075-1-quic_alokad@quicinc.com
Warning will appear when running P2P GO:
WARNING: suspicious RCU usage
drivers/net/wireless/ath/ath12k/mac.c:583 suspicious rcu_dereference_check() usage!
other info that might help us debug this:
rcu_scheduler_active = 2, debug_locks = 1
no locks held by swapper/0/0.
stack backtrace:
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 6.8.0-rc4-wt-ath+ #4
Call Trace:
<IRQ>
dump_stack_lvl+0x82/0xa0
dump_stack+0x14/0x20
lockdep_rcu_suspicious+0x214/0x3b0
ath12k_mac_get_ar_by_vdev_id+0x192/0x220 [ath12k]
ath12k_wmi_op_rx+0x2d7/0x1b40 [ath12k]
ath12k_mac_get_ar_by_vdev_id() requires its callers to have called
rcu_read_lock(), but in ath12k_wmi_p2p_noa_event() it is called without
doing so, and hence the warning was triggered.
Add rcu_read_lock() and rcu_read_unlock() to avoid warning.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Fixes: 9411eecb60 ("wifi: ath12k: implement handling of P2P NoA event")
Reported-by: Kalle Valo <quic_kvalo@quicinc.com>
Closes: https://lore.kernel.org/linux-wireless/87o7cusyvw.fsf@kernel.org/
Signed-off-by: Kang Yang <quic_kangyang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240223054505.438839-1-quic_kangyang@quicinc.com
We have support for QCA2066 now and also several new features in ath12k.
Major changes:
ath12k
* firmware-2.bin support
* support having multiple identical PCI devices (firmware needs to
have ATH12K_FW_FEATURE_MULTI_QRTR_ID)
* QCN9274: support split-PHY devices
* WCN7850: enable Power Save Mode in station mode
* WCN7850: P2P support
ath11k:
* QCA6390 & WCN6855: support 2 concurrent station interfaces
* QCA2066 support
-----BEGIN PGP SIGNATURE-----
iQFLBAABCgA1FiEEiBjanGPFTz4PRfLobhckVSbrbZsFAmXXA/YXHHF1aWNfa3Zh
bG9AcXVpY2luYy5jb20ACgkQbhckVSbrbZsfJQgAnqXLUIyHS873E4+OfEUIMZIu
/oFb9RzgU3Uv/8HWqwrXEtgbjthnxHWWVCEIR1roAEHX1vLxm5Wr0w4SsIRskwuK
8URUKIyHP4oep8TvA9uDrlQZ9PViDwW7F+Xc0nRh5c/AOi7bjMDCbJr7Sazjhsc5
JNYANHU1WSzc06hAk+3OrPON2e7EEpCkLDb7P1zVMF7uAxDovDpzGT+SXBTZu8Dw
UtiPbwTcGeUkBuMI4Mse6Jl/wAA2nWZXJXqPB1iilVwdz+VjksAZWODWS+m3UEW1
I+S8iYO0TWOSwGcu5rMyaeUMoGVSdu0Sw0h/2Ps7WGUoeZ8mT3Xwm6QrJBdpjg==
=UhMv
-----END PGP SIGNATURE-----
Merge tag 'ath-next-20240222' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/ath
ath.git patches for v6.9
We have support for QCA2066 now and also several new features in ath12k.
Major changes:
ath12k
* firmware-2.bin support
* support having multiple identical PCI devices (firmware needs to
have ATH12K_FW_FEATURE_MULTI_QRTR_ID)
* QCN9274: support split-PHY devices
* WCN7850: enable Power Save Mode in station mode
* WCN7850: P2P support
ath11k:
* QCA6390 & WCN6855: support 2 concurrent station interfaces
* QCA2066 support
Currently ieee80211_csa_finish() function finalizes CSA by scheduling a
finalizing worker using the deflink. With MLO, there is a need to do it
on a given link basis.
Pass link ID of the link on which CSA needs to be finalized.
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Link: https://msgid.link/20240130140918.1172387-6-quic_adisi@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For P2P mode, the WLAN interface may be requested to remain on a
specific channel and then to send some management frames on that
channel. Now chananel frequency of wmi_mgmt_send_cmd is set as 0. As
a result, firmware may choose a default but wrong channel.
Fix it by assigning chanfreq field with the ROC channel frequency.
This change only applies to WCN7850, other chips are not affected.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Kang Yang <quic_kangyang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240130040303.370590-11-quic_kangyang@quicinc.com
Implement remain on channel for p2p mode in ath12k_ops:
ath12k_mac_op_remain_on_channel
ath12k_mac_op_cancel_remain_on_channel
P2P device can trigger ROC scan. Then keep listening or sending management
frames on particular channels.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Kang Yang <quic_kangyang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240130040303.370590-7-quic_kangyang@quicinc.com
The Notice of Absence (NoA) attribute is used by the P2P Group Owner to
signal its absence due to power save timing, concurrent operation, or
off-channel scanning. It is also used in the P2P Presence Request-Response
mechanism.
The NoA attribute shall be present in the P2P IE in the beacon frames
transmitted by a P2P Group Owner when a NoA schedule is being advertised,
or when the CTWindow is non-zero.
So add support to update P2P information after P2P GO is up through
event WMI_P2P_NOA_EVENTID, and always put it in probe resp.
Create p2p.c and p2p.h for P2P related functions and definitions.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Kang Yang <quic_kangyang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240130040303.370590-6-quic_kangyang@quicinc.com
P2P Element is a necessary component of P2P protocol communication.
It contains the Vendor Specific Information Element which includes
the WFA OUI and an OUI Type indicating P2P.
Add P2P IE in beacon template, and implement WMI interface for it.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Kang Yang <quic_kangyang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240130040303.370590-5-quic_kangyang@quicinc.com
Current structure wmi_vdev_create_cmd is not matched to the firmware
definition. So update it.
And update vdev_stats_id_valid for vdev_stats_id.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Kang Yang <quic_kangyang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240130040303.370590-2-quic_kangyang@quicinc.com
When ath12k send TWT disable command to firmware, firmware will return a
TWT disable event to ath12k. Through the analysis of TWT disable event
status, we can easily obtain the status of TWT disable command. It can be
more convenient to debug TWT.
This patch works with WCN7850 and QCN9274.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Lingbo Kong <quic_lingbok@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240122085336.3985-3-quic_lingbok@quicinc.com
When ath12k send TWT enable command to firmware, firmware will return a TWT
enable event to ath12k. Through the analysis of TWT enable event status, we
can easily obtain the status of TWT enable command. It can be more
convenient to debug TWT.
This patch works with WCN7850 and QCN9274.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Lingbo Kong <quic_lingbok@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240122085336.3985-2-quic_lingbok@quicinc.com
In segment memory mode, firmware allocates memory segments of size
2 MB. This 2 MB memory is used by firmware for the number of peers.
This number of peer is sent from host to firmware during WMI init
command. For single-phy the number of peers sent is
TARGET_NUM_PEERS_SINGLE = 529 (512 + 17). While for split-phy number
of peers sent to firmware is TARGET_NUM_PEERS_DBS = 2 *(512 + 17) =
1058. With this 1058 number of peers firmware is unable to allocate
memory in 2 MB segment and firmware crash is observed.
Hence, fix this firmware crash by reducing the number of stations
TARGET_NUM_STATIONS for split-phy.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00188-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Aaradhana Sahu <quic_aarasahu@quicinc.com>
Co-developed-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240129065724.2310207-7-quic_rajkbhag@quicinc.com
Add support to process WMI_TLV_SERVICE_PEER_METADATA_V1A_V1B_SUPPORT
service bit. If this service bit is set by firmware, then it expects
host to set rx_peer_meta_data_ver in wmi_resource_config's flags2
with value 3 for QCN9274 to indicate as V1B meta version. If this is
not set firmware crash is seen during peer addition.
Hence, if WMI_TLV_SERVICE_PEER_METADATA_V1A_V1B_SUPPORT service bit
is set by firmware, set correct peer metadata version to avoid
firmware crash.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00188-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Harshitha Prem <quic_hprem@quicinc.com>
Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240129065724.2310207-4-quic_rajkbhag@quicinc.com
Currently while fetching for pdev id from WMI_SERVICE_READY_EXT_EVENTID
we consider 32 bit pdev_id in ath12k_wmi_caps_ext_params structure. But
Firmware sends lower 16 bit for pdev id along with higher 16 bit for
hw_link_id. Due to this wrong pdev id is fetched. This wrong pdev id
when used for WMI commands leads to Firmware crash.
Hence fetch the correct pdev id considering only the lower 16 bits.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00188-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Sowmiya Sree Elavalagan <quic_ssreeela@quicinc.com>
Co-developed-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240129065724.2310207-3-quic_rajkbhag@quicinc.com
When any VDEV is started, MBSSID flags are passed to firmware to
indicate if its a MBSSID/EMA AP vdev. If the interface is not an AP
or if the AP doesn't support MBSSID, the vdev needs to be brought up
as a non MBSSID vdev. Set these flags as a non MBSSID AP by default
which can be updated as and when MBSSID support is added in ath12k.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00188-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240129065724.2310207-2-quic_rajkbhag@quicinc.com
Currently there is no way to collect firmware log because firmware
does not send it to host. Also host does not handle WMI_DIAG_EVENTID
which is used by firmware to upload firmware log.
So add support for it by firstly enabling firmware log upload via a
QMI message, and secondly processing WMI DIAG event to expose it to
userspace via trace event.
This change applies to both WCN7850 and QCN9274.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240115023726.2866-1-quic_bqiang@quicinc.com
Currently, mac80211 hardware accesses link/radio structure directly in
multiple locations. Introduce helper function to avoid this direct
access, as this change will facilitate refactoring for Multi-link
operation support.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240118010320.3918136-2-quic_periyasa@quicinc.com
Since 'ath12k_wmi_tlv_parse_alloc()' always operates on 'skb->data,
skb->len' tuple, it may be simplified to pass the only 'skb' argument
instead (which implies refactoring of 'ath12k_pull_bcn_tx_status_ev()',
'ath12k_pull_chan_info_ev()' and 'ath12k_pull_pdev_temp_ev()' in the
same way). This is an ath12k counterpart of the recently submitted
ath11k patch and compile tested only as well.
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20231219091022.70861-1-dmantipov@yandex.ru
The ath12k active pdevs are protected by RCU but the DFS-radar and
temperature event handling code calling ath12k_mac_get_ar_by_pdev_id()
was not marked as a read-side critical section.
Mark the code in question as RCU read-side critical sections to avoid
any potential use-after-free issues.
Note that the temperature event handler looks like a place holder
currently but would still trigger an RCU lockdep splat.
Compile tested only.
Fixes: d889913205 ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices")
Cc: stable@vger.kernel.org # v6.2
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20231019113650.9060-2-johan+linaro@kernel.org
In WMI layer module, the identifier wmi_sc is used to represent
an instance of ath12k_wmi_base structure. However, within ath12k,
the convention is to use "ab" to represent an SoC "base" struct.
So change the all instances of wmi_sc to wmi_ab.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00125-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20231018153008.29820-2-quic_periyasa@quicinc.com
Certain regulatory domains could put restrictions on phy mode operation.
For example, in a few countries HE/EHT Operation is not allowed. For such
countries, firmware indicates this via phy bitmap in each reg rule.
Currently, there is no logic to parse this info and then pass it on to the
cfg80211/regulatory.
Add parsing of this phy bitmap from the regulatory channel change event and
then accordingly map it to cfg80211/regulatory flags and pass it on to it.
While at it, correct typo in debug print: s/dsf/dfs.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20231004092818.25130-1-quic_adisi@quicinc.com
Some firmware versions for WCN7850 report the default regdomain with
alpha code "na" by default when load as a world wide regdomain,
ath12k should treat it as a world wide alpha code.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230906090355.19181-1-quic_wgong@quicinc.com
ath12k prints "Received scan event for unknown vdev" when doing the
following test:
1. trigger scan
2. wait 0.2 second
3. iw reg set is issued or 11d scan complete event is sent from firmware
Reason is:
When iw reg set is issues or the 11d scan complete event is received, the
new country code will be set to the firmware, and the new regdomain info
indicated to ath12k, then the new channel list will be sent to the firmware.
The firmware will cancel the current scan after receiving WMI_SCAN_CHAN_LIST_CMDID
which is used for the new channel list, and the state of ath12k is
ATH12K_SCAN_RUNNING, then ath12k_get_ar_on_scan_abort() returns NULL and
ath12k_scan_event() returns at this point and does not indicate scan
completion to mac80211.
Indicate scan completion to mac80211 and get rid of the "Received scan
event for unknown vdev" print for the above case.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230906085746.18968-1-quic_wgong@quicinc.com
When hardware rfkill is enabled in the firmware, it will report the
capability using WMI_SYS_CAP_INFO_RFKILL bit in the WMI_SERVICE_READY event
to the host. Currently ath12k does not process this service capability. In
order to support this, update ath12k to check if the capability is enabled,
if so, send the GPIO information to firmware. When the firmware detects
hardware rfkill is enabled by the user, it will report it using
WMI_RFKILL_STATE_CHANGE_EVENTID. When ath12k receive the event, it will set
the value of rfkill_radio_on based on whether radio_state is equal to
WMI_RFKILL_RADIO_STATE_ON, then send WMI_PDEV_PARAM_RFKILL_ENABLE to
firmware.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Lingbo Kong <quic_lingbok@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230906110412.182176-1-quic_lingbok@quicinc.com
reg_cap.phy_id is extracted from WMI event and could be an unexpected value
in case some errors happen. As a result out-of-bound write may occur to
soc->hal_reg_cap. Fix it by validating reg_cap.phy_id before using it.
This is found during code review.
Compile tested only.
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230830020716.5420-1-quic_bqiang@quicinc.com
320 MHz bandwidth is reported only for single PHY mode for WCN7850, get it
from WMI_HOST_HW_MODE_SINGLE ath12k_wmi_caps_ext_params and report it for
6 GHz band.
After this patch, "iw list" shows 320 MHz support for WCN7850:
EHT Iftypes: managed
EHT PHY Capabilities: (0xe26f090010768800):
320MHz in 6GHz Supported
EHT bw=320 MHz, max NSS for MCS 8-9: Rx=0, Tx=0
EHT bw=320 MHz, max NSS for MCS 10-11: Rx=0, Tx=0
EHT bw=320 MHz, max NSS for MCS 12-13: Rx=0, Tx=0
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230828040420.2165-1-quic_wgong@quicinc.com
Currently the extraie length is directly used to allocate skb buffer. When
the length of skb is greater than the max message length which firmware
supports, error will happen in firmware side.
Hence add check for the skb length and drop extraie when overflow and
print a message.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Reviewed-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230809081657.13858-1-quic_wgong@quicinc.com
If cfg80211 is providing extraie's for a scanning process then ath12k will
copy that over to the firmware. The extraie.len is a 32 bit value in struct
element_info and describes the amount of bytes for the vendor information
elements.
The problem is the allocation of the buffer. It has to align the TLV
sections by 4 bytes. But the code was using an u8 to store the newly
calculated length of this section (with alignment). And the new
calculated length was then used to allocate the skbuff. But the actual
code to copy in the data is using the extraie.len and not the calculated
"aligned" length.
The length of extraie with IEEE80211_HW_SINGLE_SCAN_ON_ALL_BANDS enabled
was 264 bytes during tests with a wifi card. But it only allocated 8
bytes (264 bytes % 256) for it. As consequence, the code to memcpy the
extraie into the skb was then just overwriting data after skb->end. Things
like shinfo were therefore corrupted. This could usually be seen by a crash
in skb_zcopy_clear which tried to call a ubuf_info callback (using a bogus
address).
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Link: https://lore.kernel.org/r/20230809081241.32765-1-quic_wgong@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Deadlock is easily happened while shutdown wlan interface such as run
"ifconfig wlan0 down".
The reason is because when ar->regd_update_work is ran, it will
call wiphy_lock(ar->hw->wiphy) in function ath12k_regd_update() which
is running in workqueue of ieee80211_local queued by ieee80211_queue_work().
Another thread from "ifconfig wlan0 down" will also accuqire the lock
by wiphy_lock(sdata->local->hw.wiphy) in function ieee80211_stop(), and
then it call ieee80211_stop_device() to flush_workqueue(local->workqueue),
this will wait the workqueue of ieee80211_local finished. Then deadlock
will happen easily if the two thread run meanwhile.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230718024724.29120-1-quic_wgong@quicinc.com
When wlan interface is up, and 11d scan is sent to the firmware, then
firmware needs to spend couple of seconds to complete the 11d scan. If
normal scan from user space arrives to ath12k at this moment, then the
normal scan request is also sent to the firmware, but the scan started
event will be reported to ath12k until the 11d scan complete. When timed
out for the scan started in ath12k, ath12k stops the normal scan and the
firmware reports WMI_SCAN_EVENT_DEQUEUED to ath12k for the normal scan.
ath12k has no handler for the event and then timed out for the scan
completed in ath12k_scan_stop(), and ath12k prints the following error
message.
[ 1491.604750] ath12k_pci 0000:02:00.0: failed to receive scan abort comple: timed out
[ 1491.604756] ath12k_pci 0000:02:00.0: failed to stop scan: -110
[ 1491.604758] ath12k_pci 0000:02:00.0: failed to start hw scan: -110
Add a handler for WMI_SCAN_EVENT_DEQUEUED and then complete the scan to
get rid of the above error message.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230717034457.22162-1-quic_wgong@quicinc.com
Enable the feature flag to indicate the driver support for
preamble puncturing. Firmware will support this feature
by default from IEEE 802.11be onwards.
Configure the bitmap as part of VDEV start/restart and
peer association commands.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Signed-off-by: Muna Sinada <quic_msinada@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230725224034.14045-12-quic_alokad@quicinc.com
Add tags with length 0 for MLO header and partner links which
are required by the firmware for a successful association.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com>
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230725224034.14045-10-quic_alokad@quicinc.com
Add required peer association definitions and processing if the
bandwidth is 320 MHz.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Signed-off-by: Pradeep Kumar Chitrapu<quic_pradeepc@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230725224034.14045-9-quic_alokad@quicinc.com
Add new WMI tag and pass the EHT parameters for peer association
to firmware.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Signed-off-by: Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230725224034.14045-8-quic_alokad@quicinc.com
Add WMI support to process the EHT capabilities passed by
the firmware. Add required EHT specific definitions in
structures ath12k_band_cap and ath12k_wmi_svc_rdy_ext_parse.
For single_pdev chip such as WCN7850, only one pdev is created
and only one hardware is registered to mac80211. This one pdev
manages both 2.4 GHz radio and 5 GHz/6 GHz radio.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Co-developed-by: Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com>
Signed-off-by: Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com>
Co-developed-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230725224034.14045-4-quic_alokad@quicinc.com
Currently ath12k define WMI_HOST_HW_MODE_DBS_OR_SBS=5 as max hw mode
for enum wmi_host_hw_mode_config_type, it is also same for the array
ath12k_hw_mode_pri_map.
When tested with new version firmware/board data which support new
hw mode eMLSR mode with hw mode value 8, it leads overflow usage for
array ath12k_hw_mode_pri_map in function ath12k_wmi_hw_mode_caps(),
and then lead preferred_hw_mode changed to 8, and finally function
ath12k_pull_mac_phy_cap_svc_ready_ext() select the capability of hw
mode 8, but the capability of eMLSR mode report from firmware does
not support 2.4 GHz band for WCN7850, so finally 2.4 GHz band is
disabled.
Skip the hw mode which exceeds WMI_HOST_HW_MODE_MAX in function
ath12k_wmi_hw_mode_caps() helps to avoid array overflow, then the 2.4
GHz band will not be disabled.
This is to keep compatibility with newer version firmware/board data
files, this change is still needed after ath12k add eMLSR hw mode 8 in
array ath12k_hw_mode_pri_map and enum wmi_host_hw_mode_config_type,
because more hw mode maybe added in next firmware/board data version
e.g hw mode 9, then it will also lead new array overflow without this
change.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230714072405.28705-1-quic_wgong@quicinc.com
In order to support different power levels of 6 GHz AP and client, new WMI
event for regulatory (WMI_REG_CHAN_LIST_CC_EXT_EVENTID) has been added in
firmware to provide new parameters required for 6 GHz regulatory rules.
Firmware advertises its capability of handling new event in WMI service ready
event. Based on that, host needs to set host_service_flags in WMI init command
to indicate that host supports processing of this WMI event. Based on
advertised host capability, firmware sends event WMI_REG_CHAN_LIST_CC_EXT_EVENTID.
This new event contains 2G/5G/6G reg rules with additional power value fields
for 6GHz and regd is built accordingly.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0-02903-QCAHKSWPL_SILICONZ-1
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Signed-off-by: Ramya Gnanasekar <quic_rgnanase@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230502142018.20301-1-quic_rgnanase@quicinc.com
Transmission of management packets are done in a work queue. Sometimes
the workqueue does not finish Tx immediately, then it lead after the next
step of vdev delete finished, it start to send the management packet to
firmware and lead firmware crash.
ieee80211_set_disassoc() have logic of ieee80211_flush_queues() after
it send_deauth_disassoc() to ath12k, its purpose is make sure the
deauth was actually sent, so it need to change ath12k to match the
purpose of mac80211.
To address these issues wait for Tx management as well as Tx data packets.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthik M <quic_karm@quicinc.com>
Signed-off-by: Ramya Gnanasekar <quic_rgnanase@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230419095738.19859-1-quic_rgnanase@quicinc.com
When underlying hardware supports more than one band, then wiphy
is aware of all the frequency bands present. Example, say
wiphy0 is aware of 2 GHz, 5 GHz and 6 GHz band information.
Hence, when an virtual AP interface is brought up in auto channel
selection on each band. Survey is initiated from the userspace application
for all the virtual AP interfaces simultaneously.
For survey dump collection, freq_to_idx() api is used to map the index of
particular frequency to populate its survey. When the dump was collected,
the index fetched was incorrect. Example, in case of multi-hardware,
the index of channel 36 was reported as 14, because wiphy0 had index 0-13
for 2 GHz channels, instead of 0 for that ar which resulted in invalid
survey sent to userspace application.
The incorrect index was because of the mapping did not consider whether
the freq band is present in its radio structure (ar) or not.
To handle this, the freq_to_idx() api should map index for the
particular band in the ar structure.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Harshitha Prem <quic_hprem@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230320091208.25535-1-quic_hprem@quicinc.com
