Under multipath it's possible for us to offload the flow only through
the e-switch for which proper route through the uplink exists.
When the port is up and the next-hop route is set again we want to
offload through it as well.
We generate SW event from the FIB event handler when multipath port
affinity changes. The tc offloads code gets this event, goes over the
flows which were marked as of having missing route and attempts to
offload them.
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Under multipath offload scheme, as part of handling fib events, emit
mlx5 port affinity event on the enabled ports which will be handled by
the tc offloads code.
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
In a similar manner to uplink/VF LAG, under multipath we add encap peer
rule on the second port as well.
However, unlike the LAG case, we do want to allow failure for adding
one of the rules. This happens due to using a routing hint while doing
the route lookup when one path (next hop device) is down.
Introduce a new flag to indicate that route lookup failed for encap
flow. Note that a flow may still not be offloaded to hw due to missing
neighbour, in that case, the neigh update event will take care of it.
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Currently the peer flow inherits the flags from the original flow
after we've set it. At this time the flags are set according to
the flow state, e.g marked as going to slow path and such.
Even if not getting us to real bugs now, this opens the door to
get us to troubles later. Future proof the code and avoid the
inheritance, use the peer flags as were set on input when we
started adding the original flow.
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
To support multipath offload we are going to track SW multipath route
and related nexthops. To do that we register to FIB notifier and handle
the route and next-hops events and reflect that as port affinity to HW.
When there is a new multipath route entry that all next-hops are the
ports of an HCA we will activate LAG in HW.
Egress wise, we use HW LAG as the means to emulate multipath on current
HW which doesn't support port selection based on xmit hash. In the
presence of multiple VFs which use multiple SQs (send queues) this
yields fairly good distribution.
HA wise, HW LAG buys us the ability for a given RQ (receive queue) to
receive traffic from both ports and for SQs to migrate xmitting over
the active port if their base port fails.
When the route entry is being updated to single path we will update
the HW port affinity to use that port only.
If a next-hop becomes dead we update the HW port affinity to the living
port.
When all next-hops are alive again we reset the affinity to default.
Due to FW/HW limitations, when a route is deleted we are not disabling
the HW LAG since doing so will not allow us to enable it again while
VFs are bounded. Typically this is just a temporary state when a
routing daemon removes dead routes and later adds them back as needed.
This patch only handles events for AF_INET.
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
In order to offload ecmp-on-host scheme where next-hop routes are used,
we will make use of HW LAG. Add accessor function to let upper layers
in the driver to realize if the lag acts in multi-path mode.
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Instead of using the system workqueue, allocate our own workqueue.
This workqueue will be used to handle more work in the next patch.
This patch doesn't change functionality.
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The change is a refactoring step towards a multipath use case.
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
This fix checkpatch check
CHECK: Avoid using bool structure members because of possible alignment
issues
Signed-off-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
EAGAIN is treated as a specific case when we consider the attachment
successful but wait for neigh event before offloading the flow.
This can result in unwanted behavior when sub calls on the offloading
path will return EAGAIN and we pass this error up.
Instead of attaching to a specific error code return a boolean value
from the attach encap operation saying if the encap is valid or not.
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Remove the tunnel info argument which we can get from the other args.
Also reorder the args to have input args first and output args later.
This patch doesn't change functionality.
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Function mlx5e_tx_reporter_recover_from_ctx is only used within mlx5e tx
reporter, move it to be statically declared in en/reporter_tx.c.
Fixes: de8650a820 ("net/mlx5e: Add tx reporter support")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reported-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
This static inline is unnecessary and can be removed
by using the vsprintf %ph extension.
This reduces overall object size by more than 2K.
Reported-by: Louis Taylor <louis@kragniz.eu>
Signed-off-by: Joe Perches <joe@perches.com>
Reviewed-by: Louis Taylor <louis@kragniz.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make the default autosuspend delay configurable at build time.
This is useful for systems that require a non-standard value as
it avoids relying on the command line being properly set.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jakub Kicinski says:
====================
nfp: control processor DMA support and RJ45
This series starts with adding support for reporting twisted pair
media type in ethtool.
Remaining patches add support for using DMA with the control/service
processor. Currently we always copy the command data into card's
memory. DMA support allows us to have the NSP read the data from
host memory by itself. Unfortunately, the FW loading and flashing
cannot directly map the buffers for DMA because (a) the firmware
ABI returns const buffers, and (b) the buffers may be vmalloc()ed
in many mysterious/unmappable way. So just bite the bullet -
allocate new host buffer for the command and copy.
As Dirk explains, the NSP now supports updating all FWs at once
which means the max flashing time grew significantly. He bumps
the max wait to avoid timeouts.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The management firmware now supports being passed a bundle with
multiple components to be stored in flash at once. This makes it
easier to update all components to a known state with a single
user command, however, this also has the potential to increase
the time required to perform the update significantly.
The management firmware only updates the components out of a bundle
which are outdated, however, we need to make sure we can handle
the absolute worst case where a CPLD update can take a long time
to perform.
We set a very conservative total timeout of 900s which already
adds a contingency.
Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Newer versions of NSP can access host memory. Simplest access
type requires all data to be in one contiguous area. Since we
don't have the guarantee on where callers of the NSP ABI will
allocate their buffers we allocate a bounce buffer and copy
the data in and out.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DMA version of NSP communication is coming, move the code which
copies data into the NFP buffer into a separate function.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NSP expresses the buffer size in MB and 4 kB blocks. For small
buffers the kB part may make a difference, so count it in.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for reporting twisted pair port type.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It has been observed that tx queue stalls while downloading
from certain web sites (example www.speedtest.net)
The cause has been tracked down to a corner case where
dma descriptors where not setup properly. And there for a tx
completion interrupt was not signaled.
This fix corrects the problem by properly marking the end of
a multi descriptor transmission.
Fixes: 23f0703c12 ("lan743x: Add main source files for new lan743x driver")
Signed-off-by: Bryan Whitehead <Bryan.Whitehead@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When debugging an issue I found implausible values in state->pause.
Reason in that state->pause isn't initialized and later only single
bits are changed. Also the struct itself isn't initialized in
phylink_resolve(). So better initialize state->pause and other
not yet initialized fields.
v2:
- use right function name in subject
v3:
- initialize additional fields
Fixes: 9525ae8395 ("phylink: add phylink infrastructure")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recently the maximum number of queues was increased up to 8, but
NIC was not fully configured for 8 queues. In setups with more than 4 CPU
cores parts of TX traffic gets lost if the kernel routes it to queues 4th-8th.
This patch sets a tx hw traffic mode with 8 queues.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=202651
Fixes: 71a963cfc5 ("net: aquantia: increase max number of hw queues")
Reported-by: Nicholas Johnson <nicholas.johnson@outlook.com.au>
Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current implementation for UDP GRO tests is racy: the receiver
may flush the RX queue while the sending is still transmitting and
incorrectly report RX errors, with a wrong number of packet received.
Add explicit timeouts to the receiver for both connection activation
(first packet received for UDP) and reception completion, so that
in the above critical scenario the receiver will wait for the
transfer completion.
Fixes: 3327a9c463 ("selftests: add functionals test for UDP GRO")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The comphy driver for Armada 3700 by Miquèl Raynal (which is currently
in linux-next) does not actually set comphy mode when phy_set_mode_ext
is called. The mode is set at next call of phy_power_on.
Update the driver to semantics similar to mvpp2: helper
mvneta_comphy_init sets comphy mode and powers it on.
When mode is to be changed in mvneta_mac_config, first power the comphy
off, then call mvneta_comphy_init (which sets the mode to new one).
Only do this when new mode is different from old mode.
This should also work for Armada 38x, since in that comphy driver
methods power_on and power_off are unimplemented.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Claudiu Manoil says:
====================
enetc: Add mdio support and device tree nodes
This is the missing part to enable PCI probing of the ENETC ethernet
ports on the LS1028A SoC and external traffic on the LS1028A RDB board.
It's one of the first items on the TODO list for the recently merged
ENETC ethernet driver.
v3: Add DT bindings doc for ENETC connections
v4: none
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Define connection bindings (external PHY connections and internal links)
for the ENETC on-chip ethernet controllers.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each ENETC PF has its own MDIO interface, the corresponding
MDIO registers are mapped in the ENETC's Port register block.
The current patch adds a driver for these PF level MDIO buses,
so that each PF can manage directly its own external link.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The LS1028A RDB board features an Atheros PHY connected over
SGMII to the ENETC PF0 (or Port0). ENETC Port1 (PF1) has no
external connection on this board, so it can be disabled for now.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The LS1028A SoC features a PCI Integrated Endpoint Root Complex
(IERC) defining several integrated PCI devices, including the ENETC
ethernet controller integrated endpoints (IEPs). The IERC implements
ECAM (Enhanced Configuration Access Mechanism) to provide access
to the PCIe config space of the IEPs. This means the the IEPs
(including ENETC) do not support the standard PCIe BARs, instead
the Enhanced Allocation (EA) capability structures in the ECAM space
are used to fix the base addresses in the system, and the PCI
subsystem uses these structures for device enumeration and discovery.
The "ranges" entries contain basic information from these EA capabily
structures required by the kernel for device enumeration.
The current patch also enables the first 2 ENETC PFs (Physiscal
Functions) and the associated VFs (Virtual Functions), 2 VFs for
each PF. Each of these ENETC PFs has an external ethernet port
on the LS1028A SoC.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The API between clk.c and clkdev.c is purely getting the clk_hw
structure (or the struct clk if it's not CCF) and then turning that
struct clk_hw pointer into a struct clk pointer via clk_hw_create_clk().
There's no need to complicate clkdev.c with these DT parsing details
that are only relevant to the common clk framework. Move the DT parsing
logic into the core framework and just expose the APIs to get a clk_hw
pointer and convert it.
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Jeffrey Hugo <jhugo@codeaurora.org>
Cc: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
We'd like to have a pointer to the device that's consuming a particular
clk in the clk framework so we can link the consumer to the clk provider
with a PM device link. Add a device argument to clk_hw_create_clk() for
this so it can be used in subsequent patches to add and remove the link.
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Jeffrey Hugo <jhugo@codeaurora.org>
Cc: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
We want to get struct clk_hw pointers from a DT clk specifier (i.e. a
clocks property) so that we can find parent clks without searching for
globally unique clk names. This should save time by avoiding the global
string search for clks that are external to the clock controller
providing the clk and let us move away from string comparisons in
general.
Introduce of_clk_get_hw_from_clkspec() which is largely the DT parsing
part of finding clks implemented in clkdev.c and have that return a
clk_hw pointer instead of converting that into a clk pointer. This lets
us push up the clk pointer creation to the caller in clk_get() and
avoids the need to push the dev_id and con_id throughout the DT parsing
code.
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Jeffrey Hugo <jhugo@codeaurora.org>
Cc: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Currently, the core->dev entry is populated only if runtime PM is
enabled. Doing so prevents accessing the device structure in any
case.
Keep the same logic but instead of using the presence of core->dev as
the only condition, also check the status of
pm_runtime_enabled(). Then, we can set the core->dev pointer at any
time as long as a device structure is available.
This change will help supporting device links in the clock subsystem.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Jeffrey Hugo <jhugo@codeaurora.org>
Cc: Chen-Yu Tsai <wens@csie.org>
[sboyd@kernel.org: Change to a boolean flag]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The __clk_get() function is practically a private clk implementation
detail now. No architecture defines it, and given that new code should
be using the common clk framework there isn't a need for it to keep
existing just to serve clkdev purposes. Let's fold it into the
__clk_create_clk() function and make that a little more generic by
renaming it to clk_hw_create_clk(). This will allow the framework to
create a struct clk handle to a particular clk_hw pointer and link it up
as a consumer wherever that's needed.
Doing this also lets us get rid of the __clk_free_clk() API that had to
be kept in sync with __clk_put(). Splitting that API up into the "link
and unlink from consumer list" phase and "free the clk pointer" phase
allows us to reuse that logic in a couple places, simplifying the code.
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Jeffrey Hugo <jhugo@codeaurora.org>
Cc: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Factor out a base class CallGraphModelBase from CallGraphModel, so that
CallGraphModelBase can be reused.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Link: https://lkml.kernel.org/n/tip-76eybebzjwvgnadkm2oufrqi@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Instead of passing the tree root, get it from a method that can be
implemented in any derived class.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Link: https://lkml.kernel.org/n/tip-ovcv28bg4mt9swk36ypdyz14@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Factor out a base class TreeWindowBase from CallGraphWindow, so that
TreeWindowBase can be reused.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Link: https://lkml.kernel.org/n/tip-ifirw0c0mhkwxg6l12lk6k4p@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Export to the 'calls' table the newly created 'parent_id' and create an
index for it.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Link: https://lkml.kernel.org/n/tip-eybd6fnk6j9r7g643lsideoo@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Fix SQL query error "invalid input syntax for integer":
Traceback (most recent call last):
File "tools/perf/scripts/python/export-to-postgresql.py", line 465, in <module>
do_query(query, 'CREATE VIEW calls_view AS '
File "tools/perf/scripts/python/export-to-postgresql.py", line 274, in do_query
raise Exception("Query failed: " + q.lastError().text())
Exception: Query failed: ERROR: invalid input syntax for integer: ""
LINE 1: ...ch_count,call_id,return_id,CASE WHEN flags=0 THEN '' WHEN fl...
^
(22P02) QPSQL: Unable to create query
Error running python script tools/perf/scripts/python/export-to-postgresql.py
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Fixes: f08046cb30 ("perf thread-stack: Represent jmps to the start of a different symbol")
Link: https://lkml.kernel.org/n/tip-strfpdozrvg7bi1xzrivxzqt@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Remove modules not using it (SELinux and SMACK aren't
the only ones not using it).
Signed-off-by: Petr Vorel <pvorel@suse.cz>
Signed-off-by: James Morris <james.morris@microsoft.com>
Export to the 'calls' table the newly created 'parent_id'.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Link: https://lkml.kernel.org/n/tip-b09oukl48rsl9azkp2wmh0bl@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
The call_path can be used to find the parent symbol for a call but not
the exact parent call. To do that add parent_id to the call_return
export. This enables the creation of a call tree from the exported data.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Link: https://lkml.kernel.org/n/tip-6j7tzdxo67cox6kan7k22oo6@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
When TSC is not available, "timeless" decoding is used but a divide by
zero occurs if perf_time_to_tsc() is called.
Ensure the divisor is not zero.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: stable@vger.kernel.org # v4.9+
Link: https://lkml.kernel.org/n/tip-1i4j0wqoc8vlbkcizqqxpsf4@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
The message does not indicate the possibility that the symbol is not
found because the file does not exist.
Before:
$ perf record -e intel_pt//u --filter 'filter strcmp / strcpy @ foo ' ls
Symbol 'strcmp' not found.
Note that symbols must be functions.
Failed to parse address filter: 'filter strcmp / strcpy @ foo '
Filter format is: filter|start|stop|tracestop <start symbol or address> [/ <end symbol or size>] [@<file name>]
Where multiple filters are separated by space or comma.
After:
$ perf record -e intel_pt//u --filter 'filter strcmp / strcpy @ foo ' ls
File 'foo' not found or has no symbols.
Symbol 'strcmp' not found.
Note that symbols must be functions.
Failed to parse address filter: 'filter strcmp / strcpy @ foo '
Filter format is: filter|start|stop|tracestop <start symbol or address> [/ <end symbol or size>] [@<file name>]
Where multiple filters are separated by space or comma.
Reported-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Link: https://lkml.kernel.org/n/tip-dvngzxd0jkplzw1ary69dilb@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
ACPI NFIT flags field reports major errors on NVDIMM, which need
user's attention.
Update the current log to a proper error message with dev_err().
The current message string is kept for grep-compatibility.
Signed-off-by: Toshi Kani <toshi.kani@hpe.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Robert Elliott <elliott@hpe.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Ensure that if we call nfs41_sequence_process() a second time for the
same rpc_task, then we only process the results once.
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
If we have to retransmit a request, we should ensure that we reinitialise
the sequence results structure, since in the event of a signal
we need to treat the request as if it had not been sent.
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Cc: stable@vger.kernel.org
