The dsa node does not have a reg property, so remove the address from the
unit name.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
l2-cache which is either an aurora-outer-cache or an aurora-system-cache
has a reg property so the unit name should contain an address.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The skeleton.dtsi file was removed in ARM64 for different reasons as
explained in commit ("3ebee5a2e141 arm64: dts: kill skeleton.dtsi").
These also applies to ARM and it will also allow to get rid of the
following DTC warnings in the future:
"Node /memory has a reg or ranges property, but no unit name"
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
PCIe has a ranges property, so the unit name should contain an address.
Take the opportunity to use the node label instead of the full name.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
PCIe has a range property, so the unit name should contain an address.
Take the opportunity to use the node label instead of the full name.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
MDIO has a reg property so the unit name should contain an address.
Take the opportunity to use the node label instead of the full name.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Use the node label when possible. As a result it flattens the device tree
and it makes more visible the IP blocks specific to each SoC variant.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
As it was previously done for kirkwood, this adds missing node labels to
Armada 370 and XP common and SoC specific nodes to allow to reference
them more easily.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The cpurst nodes are identical in armada-370.dtsi and armada-xp.dtsi
files, so move it in the common armada-370-xp.dtsi file.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
In the dts for the Marvell Armada XP Matrix board the pcie-controller was
located under the internal-regs node whereas it belongs to the soc node.
It means that, until this fix, the pcie could not work for this board
because it didn't match the definition of the pcie-controller node in the
dtsi file. If we had a look on the decompiled dtb file we saw two
different instances of the pcie-controller node: one with the all the
resource set but disabled and the other without any resource but enabled.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Fix a spelling mistake in arch/arm/boot/dts/kirkwood-topkick.dts.
The manufacturer's name is Univer*s*al Scientific Industrial...
Compare with footer of page here:
http://www.usish.com/english/products_topkick1281p2.php
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This patch removes the legacy support of ls-chl which is converted to the
device tree.
[gregory.clement@free-electrons.com: removal extracted from a wider patch]
Signed-off-by: Ashley Hughes <ashley.hughes@blueyonder.co.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This patch converts my orion5x ls-chl Linkstation device to device tree.
[gregory.clement@free-electrons.com: fix title, add back the commit log,
move the removal of the platform in an other patch]
Signed-off-by: Ashley Hughes <ashley.hughes@blueyonder.co.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The SMSC9112 ethernet controller is connected to chip select 2
on the EBI2 bus on the APQ8060 Dragonboard. We set this up by
activating EBI2, creating a chipselect entry as a subnode, and then
putting the ethernet controller in a subnode of the chipselect.
After the chipselect is configured, the SMSC device will be
instantiated.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This adds the external bus interface EBI2 to the MSM8660 device
tree, albeit with status = "disabled" so that devices actually
using EBI2 can turn it on if needed.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add pstore support for the nexus7. This was useful in debugging
a crash where the cpus were getting stuck with irqs off and
serial output wasn't reliably working.
Cc: Kees Cook <keescook@chromium.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Andy Gross <andy.gross@linaro.org>
Cc: Vinay Simha <vinaysimha@inforcecomputing.com>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: linux-arm-msm@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add DSI and panel nodes to get graphics up and running
on the Nexus7.
This still depends on the panel driver being present
along with the rpmclk code.
Feedback would be greatly appreciated!
Cc: Archit Taneja <architt@codeaurora.org>
Cc: vinay simha <vinaysimha@inforcecomputing.com>
Cc: andy.gross@linaro.org
Cc: robdclark@gmail.com
Cc: linux-arm-msm@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Adds the core gpu, and dsi nodes for the apq8064 needed
to get graphics working on the nexus7 and other devices.
These apply on top of Archit's patch set that enables HDMI for IFC6410
Feedback would be greatly appreciated!
Cc: Archit Taneja <architt@codeaurora.org>
Cc: vinay simha <vinaysimha@inforcecomputing.com>
Cc: andy.gross@linaro.org
Cc: robdclark@gmail.com
Cc: linux-arm-msm@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add HDMI support on IFC6410. Populate the regulators required by HDMI-TX
and PHY. Establish the link between the MDP4 DTV encoder and HDMI. Create
a generic micro HDMI connector DT node. The msm drm driver doesn't parse
for HDMI connectors in DT, but it will do so later.
Cc: devicetree@vger.kernel.org
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
APQ8064 contains a MDP4 based display controller. It contains a HDMI, LVDS
and 2 DSI outputs.
Add display DT nodes for MDP4, HDMI TX and HDMI PHY. MDP4 based display
blocks have a flat device hierarchy.
Nodes for other outputs will be added later.
Cc: devicetree@vger.kernel.org
Tested-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This introduces the eMMC sdhci node and its pinctrl state
Signed-off-by: Bhushan Shah <bshah@kde.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add support for the Sierra Wireless MangOH Green board with the
Sierra Wireless WP8548 Module.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
In order to support the Sierra Wireless WP8548 module based on the
Qualcomm MDM9615 SoC, add a dtsi file.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Enable audio support for various Toradex devices as well as the GMI.
-----BEGIN PGP SIGNATURE-----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=zelz
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-4.10-arm-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/defconfig
ARM: tegra: Default configuration updates for v4.10-rc1
Enable audio support for various Toradex devices as well as the GMI.
* tag 'tegra-for-4.10-arm-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: tegra: Enable GMI driver in default configuration
ARM: tegra: Enable SGTL5000 audio
ARM: tegra: Update default configuration for v4.9-rc1
Signed-off-by: Olof Johansson <olof@lixom.net>
Adds support for GMI on Tegra20 and Tegra30 and enables the GPU on Nyan
Chromebooks. It also enables sound support on various Toradex devices.
-----BEGIN PGP SIGNATURE-----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=w7VH
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-4.10-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/dt
ARM: tegra: Device tree changes for v4.10-rc1
Adds support for GMI on Tegra20 and Tegra30 and enables the GPU on Nyan
Chromebooks. It also enables sound support on various Toradex devices.
* tag 'tegra-for-4.10-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: tegra: apalis-tk1: Drop leading 0 from unit-address
ARM: tegra: apalis/colibri t30: Integrate audio
ARM: tegra: nyan: Enable GPU node and related supply
ARM: tegra: Add Tegra30 GMI support
ARM: tegra: Add Tegra20 GMI support
Signed-off-by: Olof Johansson <olof@lixom.net>
Fix invalid GIC interrupt flags - type IRQ_TYPE_NONE is not allowed for GIC
interrupts. Although this was working but with error messages like:
genirq: Setting trigger mode 0 for irq 16 failed
Use level high interrupt instead of type none. The choice of level high was
rather an arbitrary decision hoping it will work on each platform. Tests shown
no issues so far.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=lyeE
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt-gic-flags-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt
Topic branch with DT changes for v4.10.
Fix invalid GIC interrupt flags - type IRQ_TYPE_NONE is not allowed for GIC
interrupts. Although this was working but with error messages like:
genirq: Setting trigger mode 0 for irq 16 failed
Use level high interrupt instead of type none. The choice of level high was
rather an arbitrary decision hoping it will work on each platform. Tests shown
no issues so far.
* tag 'samsung-dt-gic-flags-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: Use human-friendly symbols for interrupt properties in exynos5440
ARM: dts: exynos: Use human-friendly symbols for interrupt properties in exynos5260
ARM: dts: exynos: Use human-friendly symbols for interrupt properties in exynos5
ARM: dts: exynos: Use human-friendly symbols for interrupt properties in exynos4
ARM: dts: exynos: Use human-friendly symbols for interrupt properties in exynos3250
ARM: dts: exynos: Fix invalid GIC interrupt flags in exynos5440
ARM: dts: exynos: Fix invalid GIC interrupt flags in exynos5260
ARM: dts: exynos: Fix invalid GIC interrupt flags in exynos5410/exynos542x
ARM: dts: exynos: Fix invalid GIC interrupt flags in exynos5250
ARM: dts: exynos: Fix invalid GIC interrupt flags in exynos5
ARM: dts: exynos: Fix invalid GIC interrupt flags in exynos3250
ARM: dts: exynos: Fix invalid GIC interrupt flags in exynos4x12
ARM: dts: exynos: Fix invalid GIC interrupt flags in exynos4210
ARM: dts: exynos: Fix invalid GIC interrupt flags in exynos4
Signed-off-by: Olof Johansson <olof@lixom.net>
Fix invalid GIC interrupt flags - type IRQ_TYPE_NONE is not allowed for GIC
interrupts. Although this was working but with error messages like:
genirq: Setting trigger mode 0 for irq 16 failed
Use level high interrupt instead of type none. The choice of level high was
rather an arbitrary decision hoping it will work on each platform. Tests shown
no issues so far.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=j/xt
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt64-gic-flags-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt64
Topic branch with DT arm64 changes for v4.10.
Fix invalid GIC interrupt flags - type IRQ_TYPE_NONE is not allowed for GIC
interrupts. Although this was working but with error messages like:
genirq: Setting trigger mode 0 for irq 16 failed
Use level high interrupt instead of type none. The choice of level high was
rather an arbitrary decision hoping it will work on each platform. Tests shown
no issues so far.
* tag 'samsung-dt64-gic-flags-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
arm64: dts: exynos: Use human-friendly symbols for interrupt properties in exynos7
arm64: dts: exynos: Fix invalid GIC interrupt flags in exynos7
Signed-off-by: Olof Johansson <olof@lixom.net>
Adding the new "community" board for Armada 3700
-----BEGIN PGP SIGNATURE-----
iGoEABECACoFAlguJU8jHGdyZWdvcnkuY2xlbWVudEBmcmVlLWVsZWN0cm9ucy5j
b20ACgkQCwYYjhRyO9VNGQCfRB3BbnBCIgpu0n9wWumR7LsDmJYAoIafat62MwuH
gRsYSdrm1VVhMHwQ
=LnOL
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt64-4.10-1' of git://git.infradead.org/linux-mvebu into next/dt64
mvebu dt64 for 4.10 (part 1)
Adding the new "community" board for Armada 3700
* tag 'mvebu-dt64-4.10-1' of git://git.infradead.org/linux-mvebu:
arm64: dts: marvell: Add definition for the Globalscale Marvell ESPRESSOBin Board
Signed-off-by: Olof Johansson <olof@lixom.net>
Clean-up on thegpio driver for old SoCs(non DT)
-----BEGIN PGP SIGNATURE-----
iGoEABECACoFAlguI2sjHGdyZWdvcnkuY2xlbWVudEBmcmVlLWVsZWN0cm9ucy5j
b20ACgkQCwYYjhRyO9UpBQCfXuXP07OSFdUosB4EmN7dsXpwof0An0WBl7vez4zP
MyLYA9BpkD8FwfUs
=Aa7L
-----END PGP SIGNATURE-----
Merge tag 'mvebu-drivers-4.10-1' of git://git.infradead.org/linux-mvebu into next/soc
mvebu drivers for 4.10 (part 1)
Clean-up on thegpio driver for old SoCs(non DT)
* tag 'mvebu-drivers-4.10-1' of git://git.infradead.org/linux-mvebu:
ARM/orion/gpio: Replace three seq_printf() calls by seq_puts() in orion_gpio_dbg_show()
Signed-off-by: Olof Johansson <olof@lixom.net>
* Basic support for r8a7745 SoC
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=tBnV
-----END PGP SIGNATURE-----
Merge tag 'renesas-soc2-for-v4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/soc
Second Round of Renesas ARM Based SoC Updates for v4.10
* Basic support for r8a7745 SoC
* tag 'renesas-soc2-for-v4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: document SK-RZG1E board
ARM: shmobile: r8a7745: basic SoC support
Signed-off-by: Olof Johansson <olof@lixom.net>
- Enable tsc2004 touchscreen as a loadable module
- Enable REGULATOR_GPIO, dra71-evm needs this for MMC voltage
- Enable LP873x PMICs for dra71x-evm
- Run make savedefconfig to save some space and make it
easier to generate minimal patches against it
-----BEGIN PGP SIGNATURE-----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=h0e5
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.10/defconfig-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/defconfig
Defconfig changes for omaps for v4.10 merge window:
- Enable tsc2004 touchscreen as a loadable module
- Enable REGULATOR_GPIO, dra71-evm needs this for MMC voltage
- Enable LP873x PMICs for dra71x-evm
- Run make savedefconfig to save some space and make it
easier to generate minimal patches against it
* tag 'omap-for-v4.10/defconfig-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: omap2plus_defconfig: Run make savedefconfig to save some space
ARM: omap2plus_defconfig: Enable LP873X support
ARM: omap2plus_defconfig: Enable REGULATOR_GPIO
ARM: omap2plus_defconfig: Enable TOUCHSCREEN_TSC2004
Signed-off-by: Olof Johansson <olof@lixom.net>
We've dropped the last legacy boot board-*.c files for mach-omap2
for v4.9 so now we can start removing the unused platform_data.
All of the below has been unused since v4.9 merge window:
- Drop legacy pmic init code
- Apply seq_puts() fixes for legacy mux code, then drop it
- Drop legacy serial init
- Drop legacy i2c init
- Drop legacy PM init
- Drop legacy twl4030 platform init
- Drop legacy USB host init
- Drop legacy muxing for tusb6010, n8x0 is still using it's
platform init via pdata-quirks.c
- Drop legacy musb init
- Drop hwmod related legacy mux code
- Drop legacy hwmod data for omap3
- Drop legacy smsc911x and smc91x init
- Drop legacy board flash init
- Drop legacy ads7846 init
- Drop legacy sdram timings
-----BEGIN PGP SIGNATURE-----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=GbYF
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.10/legacy-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/soc
Legacy platform_data removal for omaps for v4.10 merge window.
We've dropped the last legacy boot board-*.c files for mach-omap2
for v4.9 so now we can start removing the unused platform_data.
All of the below has been unused since v4.9 merge window:
- Drop legacy pmic init code
- Apply seq_puts() fixes for legacy mux code, then drop it
- Drop legacy serial init
- Drop legacy i2c init
- Drop legacy PM init
- Drop legacy twl4030 platform init
- Drop legacy USB host init
- Drop legacy muxing for tusb6010, n8x0 is still using it's
platform init via pdata-quirks.c
- Drop legacy musb init
- Drop hwmod related legacy mux code
- Drop legacy hwmod data for omap3
- Drop legacy smsc911x and smc91x init
- Drop legacy board flash init
- Drop legacy ads7846 init
- Drop legacy sdram timings
* tag 'omap-for-v4.10/legacy-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (21 commits)
ARM: OMAP2+: Drop legacy sdram timings
ARM: OMAP2+: Drop legacy ads7846 init
ARM: OMAP2+: Remove legacy board-flash.c
ARM: OMAP2+: Remove legacy smsc911x and smc91x GPMC support
ARM: OMAP2+: Remove legacy data from hwmod for omap3
ARM: OMAP2+: Remove legacy mux code
ARM: OMAP2+: Remove legacy hwmod mux code
ARM: OMAP2+: Remove legacy usb-musb.c platform init code
ARM: OMAP2+: Remove legacy muxing for usb-tusb6010.c
ARM: OMAP2+: Remove legacy usb-host.c platform init code
ARM: OMAP2+: Remove legacy twl4030 platform init code
ARM: OMAP2+: Remove legacy PM init
ARM: OMAP2+: Remove legacy i2c.c platform init code
ARM: OMAP2+: Remove legacy serial.c
ARM: OMAP2+: mux: Use seq_putc() in omap_mux_dbg_signal_show()
ARM: OMAP2+: mux: Replace three seq_printf() calls by seq_puts()
ARM: OMAP: kill omap_pmic_init
ARM: OMAP2: kill omap2_pmic_init
ARM: OMAP3: kill omap3_pmic_init
ARM: OMAP3: kill omap3_pmic_get_config and twl_{get,set}_voltage
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Pull kbuild fixes from Michal Marek:
"Here are some regression fixes for kbuild:
- modversion support for exported asm symbols (Nick Piggin). The
affected architectures need separate patches adding
asm-prototypes.h.
- fix rebuilds of lib-ksyms.o (Nick Piggin)
- -fno-PIE builds (Sebastian Siewior and Borislav Petkov). This is
not a kernel regression, but one of the Debian gcc package.
Nevertheless, it's quite annoying, so I think it should go into
mainline and stable now"
* 'rc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
kbuild: Steal gcc's pie from the very beginning
kbuild: be more careful about matching preprocessed asm ___EXPORT_SYMBOL
x86/kexec: add -fno-PIE
scripts/has-stack-protector: add -fno-PIE
kbuild: add -fno-PIE
kbuild: modversions for EXPORT_SYMBOL() for asm
kbuild: prevent lib-ksyms.o rebuilds
- A series of patches to configure tps65217 PMIC interrupts for
power button, charger and usb and use them on am335x
- Configure EEPROM, LEDs and USR1 button for omap5 boards
- Add tscadc DMA properites for am33xx and am4372
- Configure baltos-ir5221 both musb channels to host mode
- Configure internal and external RTC clocks for am335x boards
- Don't reset gpio3 block on baltos
- Remove pinmux for dra72-evm for erratum i869, fix the regulators
and seprate out tps65917 support
- Add dra718-evm support
- Add minimal droid 4 xt894 support
-----BEGIN PGP SIGNATURE-----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=GYpd
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.10/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Device tree changes for omaps for v4.10 merge window:
- A series of patches to configure tps65217 PMIC interrupts for
power button, charger and usb and use them on am335x
- Configure EEPROM, LEDs and USR1 button for omap5 boards
- Add tscadc DMA properites for am33xx and am4372
- Configure baltos-ir5221 both musb channels to host mode
- Configure internal and external RTC clocks for am335x boards
- Don't reset gpio3 block on baltos
- Remove pinmux for dra72-evm for erratum i869, fix the regulators
and seprate out tps65917 support
- Add dra718-evm support
- Add minimal droid 4 xt894 support
* tag 'omap-for-v4.10/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (22 commits)
ARM: dts: Add minimal support for motorola droid 4 xt894
ARM: dts: Add support for dra718-evm
ARM: dts: dra72: Add separate dtsi for tps65917
ARM: dts: dra72-evm: Fix modelling of regulators
ARM: dts: dra72-evm: Remove pinmux configurations for erratum i869
ARM: dts: am335x-baltos: don't reset gpio3 block
ARM: dts: AM335X-evmsk: Add the internal and external clock nodes for rtc
ARM: dts: AM335X-evm: Add the internal and external clock nodes for rtc
ARM: dts: AM335X-bone-common: Add the internal and external clock nodes for rtc
ARM: dts: am335x-baltos-ir5221: use both musb channels in host mode
ARM: dts: am4372: add DMA properties for tscadc
ARM: dts: am33xx: add DMA properties for tscadc
ARM: dts: omap5 uevm: add USR1 button
ARM: dts: omap5 uevm: add LEDs
ARM: dts: omap5 uevm: add EEPROM
ARM: dts: am335x: Add the power button interrupt
ARM: dts: am335x: Add the charger interrupt
dt-bindings: mfd: Provide human readable defines for TPS65217 interrupts
ARM: dts: am335x: Support the PMIC interrupt
ARM: dts: tps65217: Add the power button device
...
Signed-off-by: Olof Johansson <olof@lixom.net>
- Add hwmod interconnect target wrapper module data for crypto
accelerators for am3xxx, am43xx and dra7
- Add support for dra71x family of SoCs
- PM fixes for omap4/5 needed for omap5 cpuidle
-----BEGIN PGP SIGNATURE-----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=hUTI
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.10/soc-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/soc
SoC changes for omaps for v4.10 merge window:
- Add hwmod interconnect target wrapper module data for crypto
accelerators for am3xxx, am43xx and dra7
- Add support for dra71x family of SoCs
- PM fixes for omap4/5 needed for omap5 cpuidle
* tag 'omap-for-v4.10/soc-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: DRA7: hwmod: Do not register RTC on DRA71
ARM: OMAP2+: board-generic: add support for DRA71x family
ARM: AMx3xx: hwmod: Add data for RNG
ARM: AM43xx: hwmod: Add data for DES
ARM: OMAP: DRA7xx: Make L4SEC clock domain SWSUP only
ARM: DRA7: hwmod: Add data for RNG IP
ARM: DRA7: hwmod: Add data for SHA IP
ARM: DRA7: hwmod: Add data for AES IP
ARM: DRA7: hwmod: Add data for DES IP
ARM: OMAP5: Add basic cpuidle MPU CSWR support
ARM: OMAP4+: Fix bad fallthrough for cpuidle
ARM: OMAP5: Fix mpuss_early_init
ARM: OMAP5: Fix build for PM code
Signed-off-by: Olof Johansson <olof@lixom.net>
- Fix mismatched interrupt numbers for tps65217, these are not yet
used
- Remove unused omapdss_early_init_of()
- Use seq_putc() for pm-debug.c
-----BEGIN PGP SIGNATURE-----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=tMf4
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.10/fixes-not-urgent-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/fixes-non-critical
Non-urgent fixes for omaps for v4.10 merge window:
- Fix mismatched interrupt numbers for tps65217, these are not yet
used
- Remove unused omapdss_early_init_of()
- Use seq_putc() for pm-debug.c
* tag 'omap-for-v4.10/fixes-not-urgent-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: pm-debug: Use seq_putc() in two functions
ARM: OMAP2+: Remove the omapdss_early_init_of() function
mfd: tps65217: Fix mismatched interrupt number
Signed-off-by: Olof Johansson <olof@lixom.net>
Support for the Allwinner A64, their first armv8 SoC.
-----BEGIN PGP SIGNATURE-----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=JkJ+
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt64-for-4.10' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into next/dt64
Allwinner arm64 DT changes for 4.10
Support for the Allwinner A64, their first armv8 SoC.
* tag 'sunxi-dt64-for-4.10' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
arm64: dts: add Pine64 support
Documentation: devicetree: add vendor prefix for Pine64
arm64: dts: add Allwinner A64 SoC .dtsi
Signed-off-by: Olof Johansson <olof@lixom.net>
Two patches to enable the dumb VGA bridges in the multi_v7 and sunxi
defconfig.
-----BEGIN PGP SIGNATURE-----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=P4mc
-----END PGP SIGNATURE-----
Merge tag 'sunxi-defconfig-for-4.10' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into next/defconfig
Allwinner defconfig changes for 4.10
Two patches to enable the dumb VGA bridges in the multi_v7 and sunxi
defconfig.
* tag 'sunxi-defconfig-for-4.10' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
ARM: multi_v7: enable VGA bridge
ARM: sunxi: Enable VGA bridge
Signed-off-by: Olof Johansson <olof@lixom.net>
- remove obsolete STiH41[56] platform support
- add Oxford Semiconductor OX820 support
- add reset index include files for OX810SE and OX820
- make drivers with boolean Kconfig options explicitly
non-modular
- allow shared pulsed resets via reset_control_reset, which
in this case means that the reset must have been triggered
once, but possibly earlier, after the function returns, and
is never triggered again for the lifetime of the reset
control
-----BEGIN PGP SIGNATURE-----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=e7kp
-----END PGP SIGNATURE-----
Merge tag 'reset-for-4.10' of git://git.pengutronix.de/git/pza/linux into next/drivers
Reset controller changes for v4.10
- remove obsolete STiH41[56] platform support
- add Oxford Semiconductor OX820 support
- add reset index include files for OX810SE and OX820
- make drivers with boolean Kconfig options explicitly
non-modular
- allow shared pulsed resets via reset_control_reset, which
in this case means that the reset must have been triggered
once, but possibly earlier, after the function returns, and
is never triggered again for the lifetime of the reset
control
* tag 'reset-for-4.10' of git://git.pengutronix.de/git/pza/linux:
reset: allow using reset_control_reset with shared reset
reset: lpc18xx: make it explicitly non-modular
reset: zynq: make it explicitly non-modular
reset: sunxi: make it explicitly non-modular
reset: socfpga: make it explicitly non-modular
reset: berlin: make it explicitly non-modular
dt-bindings: reset: oxnas: Update for OX820
dt-bindings: reset: oxnas: Add include file with reset indexes
reset: oxnas: Add OX820 support
reset: sti: softreset: Remove obsolete platforms from dt binding doc.
reset: sti: Remove STiH415/6 reset support
Signed-off-by: Olof Johansson <olof@lixom.net>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJYHmoCAAoJEHm+PkMAQRiG7RMIAI2i7Y5hpL5yCxK5AFaL4u/G
KxXfp1B1UanUTgjOmd7zGqtDYcFX9t7GTTUFixQ7/9Opr4PD9qbnatoDGSc3xjbT
msDgA1B78F1/Q3kHWfeGq32MihQ4mj5NwUCo+igUcUvvWG7mHgzErj/Nh5RoobQX
p/izdpTbrw3GX6xXB8olbG7XWHaVye/+TT3q6+gmgm8I/QEujcLeGoycE0zlhPN8
FG/JX76At/+ZM2Py7Oxo3k+oKL9CHrtOQYDp/wN0uslV5eYvvkZz0/M1HMOGZt+c
gZU5jzM17K7C4Nzo06WAuBU9wUBGc25m+cPicLlOmljnzfU+f50SKaDjZq3p7QI=
=2KUF
-----END PGP SIGNATURE-----
Merge tag 'v4.9-rc4' into sound
Bring in -rc4 patches so I can successfully merge the sound doc changes.
Recently added audio block of Exynos5410 missed global fixup of GIC
interrupt flags. Interrupt of type IRQ_TYPE_NONE is not allowed for GIC
interrupts so use level high.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
This new config parameter limits the space used for "Lock debugging:
prove locking correctness" by about 4MB. The current sparc systems have
the limitation of 32MB size for kernel size including .text, .data and
.bss sections. With PROVE_LOCKING feature, the kernel size could grow
beyond this limit and causing system boot-up issues. With this option,
kernel limits the size of the entries of lock_chains, stack_trace etc.,
so that kernel fits in required size limit. This is not visible to user
and only used for sparc.
Signed-off-by: Babu Moger <babu.moger@oracle.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
ATU 64bit addressing allows PCIe devices with 64bit DMA capabilities
to use ATU for 64bit DMA.
Signed-off-by: Tushar Dave <tushar.n.dave@oracle.com>
Reviewed-by: chris hyser <chris.hyser@oracle.com>
Acked-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add Hypervisor IOMMU v2 APIs pci_iotsb_map(), pci_iotsb_demap() and
enable sun4v dma ops to use IOMMU v2 API for all PCIe devices with
64bit DMA mask.
Signed-off-by: Tushar Dave <tushar.n.dave@oracle.com>
Reviewed-by: chris hyser <chris.hyser@oracle.com>
Acked-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to use Hypervisor (HV) IOMMU v2 API for map/demap, each PCIe
device has to be bound to IOTSB using HV API pci_iotsb_bind().
Signed-off-by: Tushar Dave <tushar.n.dave@oracle.com>
Reviewed-by: chris hyser <chris.hyser@oracle.com>
Acked-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Like legacy IOMMU, use common iommu_map_table and iommu_pool for ATU.
This change initializes iommu_map_table and iommu_pool for ATU.
Signed-off-by: Tushar Dave <tushar.n.dave@oracle.com>
Reviewed-by: chris hyser <chris.hyser@oracle.com>
Reviewed-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
