Assign the configured channel value to the EXTTS event in the timestamp
interrupt handler. Without assigning the correct channel, applications
like ts2phc will refuse to accept the event, resulting in errors such
as:
...
ts2phc[656.834]: config item end1.ts2phc.pin_index is 0
ts2phc[656.834]: config item end1.ts2phc.channel is 3
ts2phc[656.834]: config item end1.ts2phc.extts_polarity is 2
ts2phc[656.834]: config item end1.ts2phc.extts_correction is 0
...
ts2phc[656.862]: extts on unexpected channel
ts2phc[658.141]: extts on unexpected channel
ts2phc[659.140]: extts on unexpected channel
Fixes: f4da56529d ("net: stmmac: Add support for external trigger timestamping")
Cc: stable@vger.kernel.org
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Link: https://lore.kernel.org/r/20240618073821.619751-1-o.rempel@pengutronix.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
commit be27b89652 ("net: stmmac: replace priv->speed with
the portTransmitRate from the tc-cbs parameters") introduced
a problem. When deleting, it prompts "Invalid portTransmitRate
0 (idleSlope - sendSlope)" and exits. Add judgment on cbs.enable.
Only when offload is enabled, speed divider needs to be calculated.
Fixes: be27b89652 ("net: stmmac: replace priv->speed with the portTransmitRate from the tc-cbs parameters")
Signed-off-by: Xiaolei Wang <xiaolei.wang@windriver.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240617013922.1035854-1-xiaolei.wang@windriver.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The current cbs parameter depends on speed after uplinking,
which is not needed and will report a configuration error
if the port is not initially connected. The UAPI exposed by
tc-cbs requires userspace to recalculate the send slope anyway,
because the formula depends on port_transmit_rate (see man tc-cbs),
which is not an invariant from tc's perspective. Therefore, we
use offload->sendslope and offload->idleslope to derive the
original port_transmit_rate from the CBS formula.
Fixes: 1f705bc61a ("net: stmmac: Add support for CBS QDISC")
Signed-off-by: Xiaolei Wang <xiaolei.wang@windriver.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20240608143524.2065736-1-xiaolei.wang@windriver.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit 070246e467 ("net: stmmac: Fix for mismatched host/device DMA
address width") added support in the stmmac driver for platform drivers
to indicate the host DMA width, but left it up to authors of the
specific platforms to indicate if their width differed from the addr64
register read from the MAC itself.
Qualcomm's EMAC4 integration supports only up to 36 bit width (as
opposed to the addr64 register indicating 40 bit width). Let's indicate
that in the platform driver to avoid a scenario where the driver will
allocate descriptors of size that is supported by the CPU which in our
case is 36 bit, but as the addr64 register is still capable of 40 bits
the device will use two descriptors as one address.
Fixes: 8c4d92e82d ("net: stmmac: dwmac-qcom-ethqos: add support for emac4 on sa8775p platforms")
Signed-off-by: Sagar Cheluvegowda <quic_scheluve@quicinc.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- optimize DMA sync calls when they are no-ops (Alexander Lobakin)
- fix swiotlb padding for untrusted devices (Michael Kelley)
- add documentation for swiotb (Michael Kelley)
-----BEGIN PGP SIGNATURE-----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=Pa8W
-----END PGP SIGNATURE-----
Merge tag 'dma-mapping-6.10-2024-05-20' of git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping updates from Christoph Hellwig:
- optimize DMA sync calls when they are no-ops (Alexander Lobakin)
- fix swiotlb padding for untrusted devices (Michael Kelley)
- add documentation for swiotb (Michael Kelley)
* tag 'dma-mapping-6.10-2024-05-20' of git://git.infradead.org/users/hch/dma-mapping:
dma: fix DMA sync for drivers not calling dma_set_mask*()
xsk: use generic DMA sync shortcut instead of a custom one
page_pool: check for DMA sync shortcut earlier
page_pool: don't use driver-set flags field directly
page_pool: make sure frag API fields don't span between cachelines
iommu/dma: avoid expensive indirect calls for sync operations
dma: avoid redundant calls for sync operations
dma: compile-out DMA sync op calls when not used
iommu/dma: fix zeroing of bounce buffer padding used by untrusted devices
swiotlb: remove alloc_size argument to swiotlb_tbl_map_single()
Documentation/core-api: add swiotlb documentation
Move the EST structure to struct stmmac_priv, because the
EST configs don't look like platform config, but EST is
enabled in runtime with the settings retrieved for the TC
TAPRIO feature also in runtime. So it's better to have the
EST-data preserved in the driver private data instead of
the platform data storage.
Signed-off-by: Xiaolei Wang <xiaolei.wang@windriver.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Link: https://lore.kernel.org/r/20240513014346.1718740-3-xiaolei.wang@windriver.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for the Renesas RZ/N1 GMAC. This support can make use of a
custom RZ/N1 PCS which is fetched by parsing the pcs-handle device tree
property.
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Co-developed-by: Romain Gantois <romain.gantois@bootlin.com>
Signed-off-by: Romain Gantois <romain.gantois@bootlin.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Hariprasad Kelam <hkelam@marvell.com>
Link: https://lore.kernel.org/r/20240513-rzn1-gmac1-v7-6-6acf58b5440d@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use the newly introduced pcs_init() and pcs_exit() operations to
create and destroy the PCS instance at a more appropriate moment during
the driver lifecycle, thereby avoiding publishing a network device to
userspace that has not yet finished its PCS initialisation.
There are other similar issues with this driver which remain
unaddressed, but these are out of scope for this patch.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
[rgantois: removed second parameters of new callbacks]
Signed-off-by: Romain Gantois <romain.gantois@bootlin.com>
Reviewed-by: Hariprasad Kelam <hkelam@marvell.com>
Link: https://lore.kernel.org/r/20240513-rzn1-gmac1-v7-5-6acf58b5440d@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Introduce a mechanism whereby platforms can create their PCS instances
prior to the network device being published to userspace, but after
some of the core stmmac initialisation has been completed. This means
that the data structures that platforms need will be available.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Co-developed-by: Romain Gantois <romain.gantois@bootlin.com>
Signed-off-by: Romain Gantois <romain.gantois@bootlin.com>
Reviewed-by: Hariprasad Kelam <hkelam@marvell.com>
Link: https://lore.kernel.org/r/20240513-rzn1-gmac1-v7-4-6acf58b5440d@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A pcs_init() callback will be introduced to stmmac in a future patch. This
new function will be called during the hardware initialization phase.
Instead of separately initializing XPCS and PCS components, let's group all
PCS-related hardware initialization logic in the current
stmmac_xpcs_setup() function.
Rename stmmac_xpcs_setup() to stmmac_pcs_setup() and move the conditional
call to stmmac_xpcs_setup() inside the function itself.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Co-developed-by: Romain Gantois <romain.gantois@bootlin.com>
Signed-off-by: Romain Gantois <romain.gantois@bootlin.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Hariprasad Kelam <hkelam@marvell.com>
Link: https://lore.kernel.org/r/20240513-rzn1-gmac1-v7-3-6acf58b5440d@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently the XPCS handler destruction is performed in the
stmmac_mdio_unregister() method. It doesn't look good because the handler
isn't originally created in the corresponding protagonist
stmmac_mdio_unregister(), but in the stmmac_xpcs_setup() function. In
order to have more coherent MDIO and XPCS setup/cleanup procedures,
let's move the DW XPCS destruction to the dedicated stmmac_pcs_clean()
method.
This method will also be used to cleanup PCS hardware using the
pcs_exit() callback that will be introduced to stmmac in a subsequent
patch.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Co-developed-by: Romain Gantois <romain.gantois@bootlin.com>
Signed-off-by: Romain Gantois <romain.gantois@bootlin.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Hariprasad Kelam <hkelam@marvell.com>
Link: https://lore.kernel.org/r/20240513-rzn1-gmac1-v7-2-6acf58b5440d@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently the ipq806x dwmac driver is almost always used attached to the
CPU port of a switch and phy-mode was always set to "rgmii" or "sgmii".
Some device came up with a special configuration where the PHY is
directly attached to the GMAC port and in those case phy-mode needs to
be set to "rgmii-id" to make the PHY correctly work and receive packets.
Since the driver supports only "rgmii" and "sgmii" mode, when "rgmii-id"
(or variants) mode is set, the mode is rejected and probe fails.
Add support also for these phy-modes to correctly setup PHYs that requires
delay applied to tx/rx.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
XSk infra's been using its own DMA sync shortcut to try avoiding
redundant function calls. Now that there is a generic one, remove
the custom implementation and rely on the generic helpers.
xsk_buff_dma_sync_for_cpu() doesn't need the second argument anymore,
remove it.
Signed-off-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Simon reported that ndo_change_mtu() methods were never
updated to use WRITE_ONCE(dev->mtu, new_mtu) as hinted
in commit 501a90c945 ("inet: protect against too small
mtu values.")
We read dev->mtu without holding RTNL in many places,
with READ_ONCE() annotations.
It is time to take care of ndo_change_mtu() methods
to use corresponding WRITE_ONCE()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Simon Horman <horms@kernel.org>
Closes: https://lore.kernel.org/netdev/20240505144608.GB67882@kernel.org/
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Simon Horman <horms@kernel.org>
Acked-by: Shannon Nelson <shannon.nelson@amd.com>
Link: https://lore.kernel.org/r/20240506102812.3025432-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
After a set of recent fixes the stmmac_phy_setup() and
stmmac_reinit_queues() methods have turned to having some duplicated code.
Let's get rid from the duplication by moving the MAC-capabilities
initialization to the PHYLINK MAC-capabilities getter. The getter is
called during each network device interface open/close cycle. So the
MAC-capabilities will be initialized in generic device open procedure and
in case of the Tx/Rx queues re-initialization as the original code
semantics implies.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Romain Gantois <romain.gantois@bootlin.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Since recent commits the stmmac_ops::phylink_get_caps() callback has no
longer been responsible for the phylink MAC capabilities getting, but
merely updates the MAC capabilities in the mac_device_info:🔗:caps
field. Rename the callback to comply with the what the method does now.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Romain Gantois <romain.gantois@bootlin.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Here is the list of the MAC capabilities specific to the particular DW MAC
IP-cores currently supported by the driver:
DW MAC100: MAC_ASYM_PAUSE | MAC_SYM_PAUSE |
MAC_10 | MAC_100
DW GMAC: MAC_ASYM_PAUSE | MAC_SYM_PAUSE |
MAC_10 | MAC_100 | MAC_1000
Allwinner sun8i MAC: MAC_ASYM_PAUSE | MAC_SYM_PAUSE |
MAC_10 | MAC_100 | MAC_1000
DW QoS Eth: MAC_ASYM_PAUSE | MAC_SYM_PAUSE |
MAC_10 | MAC_100 | MAC_1000 | MAC_2500FD
if there is more than 1 active Tx/Rx queues:
MAC_ASYM_PAUSE | MAC_SYM_PAUSE |
MAC_10FD | MAC_100FD | MAC_1000FD | MAC_2500FD
DW XGMAC: MAC_ASYM_PAUSE | MAC_SYM_PAUSE |
MAC_1000FD | MAC_2500FD | MAC_5000FD | MAC_10000FD
DW XLGMAC: MAC_ASYM_PAUSE | MAC_SYM_PAUSE |
MAC_1000FD | MAC_2500FD | MAC_5000FD | MAC_10000FD |
MAC_25000FD | MAC_40000FD | MAC_50000FD | MAC_100000FD
As you can see there are only two common capabilities:
MAC_ASYM_PAUSE | MAC_SYM_PAUSE.
Meanwhile what is currently implemented defines 10/100/1000 link speeds
for all IP-cores, which is definitely incorrect for DW MAC100, DW XGMAC
and DW XLGMAC devices.
Seeing the flow-control is implemented as a callback for each MAC IP-core
(see dwmac100_flow_ctrl(), dwmac1000_flow_ctrl(), sun8i_dwmac_flow_ctrl(),
etc) and since the MAC-specific setup() method is supposed to be called
for each available DW MAC-based device, the capabilities initialization
can be freely moved to these setup() functions, thus correctly setting up
the MAC-capabilities for each IP-core (including the Allwinner Sun8i). A
new stmmac_link::caps field was specifically introduced for that so to
have all link-specific info preserved in a single structure.
Note the suggested change fixes three earlier commits at a time. The
commit 5b0d7d7da6 ("net: stmmac: Add the missing speeds that XGMAC
supports") permitted the 10-100 link speeds and 1G half-duplex mode for DW
XGMAC IP-core even though it doesn't support them. The commit df7699c70c
("net: stmmac: Do not cut down 1G modes") incorrectly added the MAC1000
capability to the DW MAC100 IP-core. Similarly to the DW XGMAC the commit
8a880936e9 ("net: stmmac: Add XLGMII support") incorrectly permitted the
10-100 link speeds and 1G half-duplex mode for DW XLGMAC IP-core.
Fixes: 5b0d7d7da6 ("net: stmmac: Add the missing speeds that XGMAC supports")
Fixes: df7699c70c ("net: stmmac: Do not cut down 1G modes")
Fixes: 8a880936e9 ("net: stmmac: Add XLGMII support")
Suggested-by: Russell King (Oracle) <linux@armlinux.org.uk>
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Romain Gantois <romain.gantois@bootlin.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
It's possible to have the maximum link speed being artificially limited on
the platform-specific basis. It's done either by setting up the
plat_stmmacenet_data::max_speed field or by specifying the "max-speed"
DT-property. In such cases it's required that any specific
MAC-capabilities re-initializations would take the limit into account. In
particular the link speed capabilities may change during the number of
active Tx/Rx queues re-initialization. But the currently implemented
procedure doesn't take the speed limit into account.
Fix that by calling phylink_limit_mac_speed() in the
stmmac_reinit_queues() method if the speed limitation was required in the
same way as it's done in the stmmac_phy_setup() function.
Fixes: 95201f36f3 ("net: stmmac: update MAC capabilities when tx queues are updated")
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Romain Gantois <romain.gantois@bootlin.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
There are three DW MAC IP-cores which can have the multiple Tx/Rx queues
enabled:
DW GMAC v3.7+ with AV feature,
DW QoS Eth v4.x/v5.x,
DW XGMAC/XLGMAC
Based on the respective HW databooks, only the DW QoS Eth IP-core doesn't
support the half-duplex link mode in case if more than one queues enabled:
"In multiple queue/channel configurations, for half-duplex operation,
enable only the Q0/CH0 on Tx and Rx. For single queue/channel in
full-duplex operation, any queue/channel can be enabled."
The rest of the IP-cores don't have such constraint. Thus in order to have
the constraint applied for the DW QoS Eth MACs only, let's move the it'
implementation to the respective MAC-capabilities getter and make sure the
getter is called in the queues re-init procedure.
Fixes: b6cfffa7ad ("stmmac: fix DMA channel hang in half-duplex mode")
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Romain Gantois <romain.gantois@bootlin.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The missing statistics including Rx_Receive_Error_Packets and
Tx_OSize_Packets_Good.
Signed-off-by: Minda Chen <minda.chen@starfivetech.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
XGMAC MMC has already added LPI statistics. GMAC MMC lack of these
statistics. Add register definition and reading the LPI statistics
from registers.
Signed-off-by: Minda Chen <minda.chen@starfivetech.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver should ensure that same priority is not mapped to multiple
rx queues. From DesignWare Cores Ethernet Quality-of-Service
Databook, section 17.1.29 MAC_RxQ_Ctrl2:
"[...]The software must ensure that the content of this field is
mutually exclusive to the PSRQ fields for other queues, that is,
the same priority is not mapped to multiple Rx queues[...]"
Previously rx_queue_priority() function was:
- clearing all priorities from a queue
- adding new priorities to that queue
After this patch it will:
- first assign new priorities to a queue
- then remove those priorities from all other queues
- keep other priorities previously assigned to that queue
Fixes: a8f5102af2 ("net: stmmac: TX and RX queue priority configuration")
Fixes: 2142754f8b ("net: stmmac: Add MAC related callbacks for XGMAC2")
Signed-off-by: Piotr Wejman <piotrwejman90@gmail.com>
Link: https://lore.kernel.org/r/20240401192239.33942-1-piotrwejman90@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There is a reocurring issue with stmmac controllers where the MAC fails to
initialize its hardware if an RX clock signal isn't provided on the MAC/PHY
link.
This causes issues when PHY or PCS devices either go into suspend while
cutting the RX clock or do not bring the clock signal up early enough for
the MAC to initialize successfully.
Set the mac_requires_rxc flag in the stmmac phylink config so that PHY/PCS
drivers know to keep the RX clock up at all times.
Reported-by: Clark Wang <xiaoning.wang@nxp.com>
Link: https://lore.kernel.org/all/20230202081559.3553637-1-xiaoning.wang@nxp.com/
Reported-by: Clément Léger <clement.leger@bootlin.com>
Link: https://lore.kernel.org/linux-arm-kernel/20230116103926.276869-4-clement.leger@bootlin.com/
Co-developed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Romain Gantois <romain.gantois@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240326-rxc_bugfix-v6-5-24a74e5c761f@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Global stmmac support for early initialization of PCS devices requires a
generic PCS reference that can be passed to phylink_pcs_pre_init().
Currently, the mac_device_info struct contains only one PCS field, which is
specific to the Lynx model.
As PCS models are hardware-specific, it is more appropriate to have a
generic PCS field in the mac_device_info struct.
Refactor the lynx_pcs field into a generic phylink_pcs field.
Signed-off-by: Romain Gantois <romain.gantois@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240326-rxc_bugfix-v6-4-24a74e5c761f@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When initializing attached PHYs, there are some cases where we don't expect
any PHY to be connected. The logic uses conditions based on various local
PCS configuration, but also calls-in phylink_expects_phy() via
stmmac_init_phy(), which is enough to ensure we don't try to initialize a
PHY when using a Lynx PCS, as long as we have the phy_interface set to a
802.3z mode and are using inband negociation.
Drop the lynx check, making the stmmac generic code more pcs_lynx-agnostic.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
[rgantois: commit log]
Signed-off-by: Romain Gantois <romain.gantois@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240326-rxc_bugfix-v6-3-24a74e5c761f@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
__napi_alloc_skb() is napi_alloc_skb() with the added flexibility
of choosing gfp_mask. This is a NAPI function, so GFP_ATOMIC is
implied. The only practical choice the caller has is whether to
set __GFP_NOWARN. But that's a false choice, too, allocation failures
in atomic context will happen, and printing warnings in logs,
effectively for a packet drop, is both too much and very likely
non-actionable.
This leads me to a conclusion that most uses of napi_alloc_skb()
are simply misguided, and should use __GFP_NOWARN in the first
place. We also have a "standard" way of reporting allocation
failures via the queue stat API (qstats::rx-alloc-fail).
The direct motivation for this patch is that one of the drivers
used at Meta calls napi_alloc_skb() (so prior to this patch without
__GFP_NOWARN), and the resulting OOM warning is the top networking
warning in our fleet.
Reviewed-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20240327040213.3153864-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
of_gpio.h is deprecated and subject to remove.
The driver doesn't use it, simply remove the unused header.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is just a trivial fix for a typo in a comment, no functional
changes.
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Yanteng Si <siyanteng@loongson.cn>
Link: https://lore.kernel.org/r/20240228112447.1490926-1-siyanteng@loongson.cn
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Currently when suspending driver and stopping workqueue it is checked whether
workqueue is not NULL and if so, it is destroyed.
Function destroy_workqueue() does drain queue and does clear variable, but
it does not set workqueue variable to NULL. This can cause kernel/module
panic if code attempts to clear workqueue that was not initialized.
This scenario is possible when resuming suspended driver in stmmac_resume(),
because there is no handling for failed stmmac_hw_setup(),
which can fail and return if DMA engine has failed to initialize,
and workqueue is initialized after DMA engine.
Should DMA engine fail to initialize, resume will proceed normally,
but interface won't work and TX queue will eventually timeout,
causing 'Reset adapter' error.
This then does destroy workqueue during reset process.
And since workqueue is initialized after DMA engine and can be skipped,
it will cause kernel/module panic.
To secure against this possible crash, set workqueue variable to NULL when
destroying workqueue.
Log/backtrace from crash goes as follows:
[88.031977]------------[ cut here ]------------
[88.031985]NETDEV WATCHDOG: eth0 (sxgmac): transmit queue 1 timed out
[88.032017]WARNING: CPU: 0 PID: 0 at net/sched/sch_generic.c:477 dev_watchdog+0x390/0x398
<Skipping backtrace for watchdog timeout>
[88.032251]---[ end trace e70de432e4d5c2c0 ]---
[88.032282]sxgmac 16d88000.ethernet eth0: Reset adapter.
[88.036359]------------[ cut here ]------------
[88.036519]Call trace:
[88.036523] flush_workqueue+0x3e4/0x430
[88.036528] drain_workqueue+0xc4/0x160
[88.036533] destroy_workqueue+0x40/0x270
[88.036537] stmmac_fpe_stop_wq+0x4c/0x70
[88.036541] stmmac_release+0x278/0x280
[88.036546] __dev_close_many+0xcc/0x158
[88.036551] dev_close_many+0xbc/0x190
[88.036555] dev_close.part.0+0x70/0xc0
[88.036560] dev_close+0x24/0x30
[88.036564] stmmac_service_task+0x110/0x140
[88.036569] process_one_work+0x1d8/0x4a0
[88.036573] worker_thread+0x54/0x408
[88.036578] kthread+0x164/0x170
[88.036583] ret_from_fork+0x10/0x20
[88.036588]---[ end trace e70de432e4d5c2c1 ]---
[88.036597]Unable to handle kernel NULL pointer dereference at virtual address 0000000000000004
Fixes: 5a5586112b ("net: stmmac: support FPE link partner hand-shaking procedure")
Signed-off-by: Jakub Raczynski <j.raczynski@samsung.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Updating link clock rate for different speeds is only needed when
using RGMII, as that mode requires changing clock speed when the link
speed changes. Let's restrict updating the link clock speed in
ethqos_update_link_clk() to just RGMII. Other modes such as SGMII
only need to enable the link clock (which is already done in probe).
Signed-off-by: Sarosh Hasan <quic_sarohasa@quicinc.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Tested-by: Andrew Halaney <ahalaney@redhat.com> # sa8775p-ride
Reviewed-by: Abhishek Chauhan <quic_abchauha@quicinc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently using plain XDP/ZC sockets on stmmac results in a kernel crash:
|[ 255.822584] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000
|[...]
|[ 255.822764] Call trace:
|[ 255.822766] stmmac_tx_clean.constprop.0+0x848/0xc38
The program counter indicates xsk_tx_metadata_complete(). It works on
compl->tx_timestamp, which is not set by xsk_tx_metadata_to_compl() due to
missing meta data. Therefore, call xsk_tx_metadata_complete() only when
meta data is actually used.
Tested on imx93 without XDP, with XDP and with XDP/ZC.
Fixes: 1347b41931 ("net: stmmac: Add Tx HWTS support to XDP ZC")
Suggested-by: Serge Semin <fancer.lancer@gmail.com>
Tested-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/netdev/87r0h7wg8u.fsf@kurt.kurt.home/
Acked-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Link: https://lore.kernel.org/r/20240222-stmmac_xdp-v2-1-4beee3a037e4@linutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The MMC IPC interrupt status and interrupt mask registers are
of little use as Ethernet statistics, but incrementing counters
based on the current interrupt and interrupt mask registers
makes them actively misleading.
For example, if the interrupt mask is set to 0x08420842,
the current code will increment by that amount each iteration,
leading to the following sequence of nonsense:
mmc_rx_ipc_intr_mask: 969816526
mmc_rx_ipc_intr_mask: 1108361744
These registers have been included in the Ethernet statistics
since the first version of MMC back in 2011 (commit 1c901a46d5).
That commit also mentions the MMC interrupts as
"something to add later (if actually useful)".
If the registers are actually useful, they should probably
be part of the Ethernet register dump instead of statistics,
but for now, drop the counters for mmc_rx_ipc_intr and
mmc_rx_ipc_intr_mask completely.
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Link: https://lore.kernel.org/r/20240223-stmmac_stats-v3-1-5d483c2a071a@axis.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Serdes phy needs to operate at 2500 mode for 2.5G speed and 1000
mode for 1G/100M/10M speed.
Added changes to configure serdes phy and mac based on link speed.
Changing serdes phy speed involves multiple register writes for
serdes block. To avoid redundant write operations only update serdes
phy when new speed is different.
For 2500 speed MAC PCS autoneg needs to disabled. Added changes to
disable MAC PCS autoneg if ANE parameter is not set.
Signed-off-by: Sneh Shah <quic_snehshah@quicinc.com>
Tested-by: Abhishek Chauhan <quic_abchauha@quicinc.com> # sa8775p-ride
Reviewed-by: Abhishek Chauhan <quic_abchauha@quicinc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix EST offset for dwmac 5.10.
Currently configuring Qbv doesn't work as expected. The schedule is
configured, but never confirmed:
|[ 128.250219] imx-dwmac 428a0000.ethernet eth1: configured EST
The reason seems to be the refactoring of the EST code which set the wrong
EST offset for the dwmac 5.10. After fixing this it works as before:
|[ 106.359577] imx-dwmac 428a0000.ethernet eth1: configured EST
|[ 128.430715] imx-dwmac 428a0000.ethernet eth1: EST: SWOL has been switched
Tested on imx93.
Fixes: c3f3b97238 ("net: stmmac: Refactor EST implementation")
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/20240220-stmmac_est-v1-1-c41f9ae2e7b7@linutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If 'dev' or 'data' is NULL, the 'priv' variable has an incorrect address
when dereferencing calling netdev_err().
Since we get as 'dev_id' or 'data' what was passed as the 'dev' argument
to request_irq() during interrupt initialization (that is, the net_device
and rx/tx queue pointers initialized at the time of the call) and since
there are usually no checks for the 'dev_id' argument in such handlers
in other drivers, remove these checks from the handlers in stmmac driver.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 8532f613bc ("net: stmmac: introduce MSI Interrupt routines for mac, safety, RX & TX")
Signed-off-by: Pavel Sakharov <p.sakharov@ispras.ru>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 8a7cb245cf ("net: stmmac: Do not enable RX FIFO overflow
interrupts") disabled the RX FIFO overflow interrupts. However, it left the
status variable around, but never checks it.
As stmmac_host_mtl_irq_status() returns only 0 now, the code can be
simplified.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Link: https://lore.kernel.org/r/20240208-stmmac_irq-v1-1-8bab236026d4@linutronix.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The cited commit introduces and uses the string constants dpp_tx_err and
dpp_rx_err. These are assigned to constant fields of the array
dwxgmac3_error_desc.
It has been reported that on GCC 6 and 7.5.0 this results in warnings
such as:
.../dwxgmac2_core.c:836:20: error: initialiser element is not constant
{ true, "TDPES0", dpp_tx_err },
I have been able to reproduce this using: GCC 7.5.0, 8.4.0, 9.4.0 and 10.5.0.
But not GCC 13.2.0.
So it seems this effects older compilers but not newer ones.
As Jon points out in his report, the minimum compiler supported by
the kernel is GCC 5.1, so it does seem that this ought to be fixed.
It is not clear to me what combination of 'const', if any, would address
this problem. So this patch takes of using #defines for the string
constants
Compile tested only.
Fixes: 46eba193d0 ("net: stmmac: xgmac: fix handling of DPP safety error for DMA channels")
Reported-by: Jon Hunter <jonathanh@nvidia.com>
Closes: https://lore.kernel.org/netdev/c25eb595-8d91-40ea-9f52-efa15ebafdbc@nvidia.com/
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202402081135.lAxxBXHk-lkp@intel.com/
Signed-off-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240208-xgmac-const-v1-1-e69a1eeabfc8@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support to listen HW safety IRQ like ECC(error
correction code), DPP(data path parity), FSM(finite state
machine) fault in common IRQ line.
Signed-off-by: Suraj Jaiswal <quic_jsuraj@quicinc.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TSO and TBS cannot co-exist. TBS requires special descriptor to be
allocated at bootup. Initialising Tx queues at probe to support
TSO and TBS can help in allocating those resources at bootup.
TX queues with TBS can support etf qdisc hw offload.
This is similar to the patch raised by NXP
commit 3b12ec8f61 ("net: stmmac: dwmac-imx: set TSO/TBS TX queues default settings")
Tested-by: Andrew Halaney <ahalaney@redhat.com> # sa8775p-ride
Signed-off-by: Abhishek Chauhan <quic_abchauha@quicinc.com>
Reviewed-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cross-merge networking fixes after downstream PR.
No conflicts.
Adjacent changes:
drivers/net/ethernet/stmicro/stmmac/common.h
38cc3c6dcc ("net: stmmac: protect updates of 64-bit statistics counters")
fd5a6a7131 ("net: stmmac: est: Per Tx-queue error count for HLBF")
c5c3e1bfc9 ("net: stmmac: Offload queueMaxSDU from tc-taprio")
drivers/net/wireless/microchip/wilc1000/netdev.c
c901388028 ("wifi: fill in MODULE_DESCRIPTION()s for wilc1000")
328efda22a ("wifi: wilc1000: do not realloc workqueue everytime an interface is added")
net/unix/garbage.c
11498715f2 ("af_unix: Remove io_uring code for GC.")
1279f9d9de ("af_unix: Call kfree_skb() for dead unix_(sk)->oob_skb in GC.")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
stmmac_ethtool_op_get_eee() sets both eee_enabled and eee_active, and
then goes on to call phylink_ethtool_get_eee().
phylink_ethtool_get_eee() will return -EOPNOTSUPP if there is no PHY
present, otherwise calling phy_ethtool_get_eee() which in turn will call
genphy_c45_ethtool_get_eee().
genphy_c45_ethtool_get_eee() will overwrite eee_enabled and eee_active
with its own interpretation from the PHYs settings and negotiation
result.
Thus, when there is no PHY, stmmac_ethtool_op_get_eee() will fail with
-EOPNOTSUPP, meaning eee_enabled and eee_active will not be returned to
userspace. When there is a PHY, eee_enabled and eee_active will be
overwritten by phylib, making the setting of these members in
stmmac_ethtool_op_get_eee() entirely unnecessary.
Remove this code, thus simplifying stmmac_ethtool_op_get_eee().
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/E1rWbMs-002cCV-EE@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As explained by a comment in <linux/u64_stats_sync.h>, write side of struct
u64_stats_sync must ensure mutual exclusion, or one seqcount update could
be lost on 32-bit platforms, thus blocking readers forever. Such lockups
have been observed in real world after stmmac_xmit() on one CPU raced with
stmmac_napi_poll_tx() on another CPU.
To fix the issue without introducing a new lock, split the statics into
three parts:
1. fields updated only under the tx queue lock,
2. fields updated only during NAPI poll,
3. fields updated only from interrupt context,
Updates to fields in the first two groups are already serialized through
other locks. It is sufficient to split the existing struct u64_stats_sync
so that each group has its own.
Note that tx_set_ic_bit is updated from both contexts. Split this counter
so that each context gets its own, and calculate their sum to get the total
value in stmmac_get_ethtool_stats().
For the third group, multiple interrupts may be processed by different CPUs
at the same time, but interrupts on the same CPU will not nest. Move fields
from this group to a newly created per-cpu struct stmmac_pcpu_stats.
Fixes: 133466c3bb ("net: stmmac: use per-queue 64 bit statistics where necessary")
Link: https://lore.kernel.org/netdev/Za173PhviYg-1qIn@torres.zugschlus.de/t/
Cc: stable@vger.kernel.org
Signed-off-by: Petr Tesarik <petr@tesarici.cz>
Reviewed-by: Jisheng Zhang <jszhang@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
DDPP is copied from Synopsys Data book:
DDPP: Disable Data path Parity Protection.
When it is 0x0, Data path Parity Protection is enabled.
When it is 0x1, Data path Parity Protection is disabled.
The macro name should be XGMAC_DPP_DISABLE.
Fixes: 46eba193d0 ("net: stmmac: xgmac: fix handling of DPP safety error for DMA channels")
Signed-off-by: Furong Xu <0x1207@gmail.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/20240203053133.1129236-1-0x1207@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
