The VEB (virtual embedded switch) as a switch element can be
connected according datasheet though its uplink to:
- Physical port
- Port Virtualizer (not used directly by i40e driver but can
be present in MFP mode where the physical port is shared
between PFs)
- No uplink (aka floating VEB)
But VEB uplink cannot be connected to another VEB and any attempt
to do so results in:
"i40e 0000:02:00.0: couldn't add VEB, err -EIO aq_err I40E_AQ_RC_ENOENT"
that indicates "the uplink SEID does not point to valid element".
Remove this logic from the driver code this way:
1) For debugfs only allow to build floating VEB (uplink_seid == 0)
or main VEB (uplink_seid == mac_seid)
2) Do not recurse in i40e_veb_link_event() as no VEB cannot have
sub-VEBs
3) Ditto for i40e_veb_rebuild() + simplify the function as we know
that the VEB for rebuild can be only the main LAN VEB or some
of the floating VEBs
4) In i40e_rebuild() there is no need to check veb->uplink_seid
as the possible ones are 0 and MAC SEID
5) In i40e_vsi_release() do not take into account VEBs whose
uplink is another VEB as this is not possible
6) Remove veb_idx field from i40e_veb as a VEB cannot have
sub-VEBs
Tested using i40e debugfs interface:
1) Initial state
[root@cnb-03 net-next]# CMD="/sys/kernel/debug/i40e/0000:02:00.0/command"
[root@cnb-03 net-next]# echo dump switch > $CMD
[root@cnb-03 net-next]# dmesg -c
[ 98.440641] i40e 0000:02:00.0: header: 3 reported 3 total
[ 98.446053] i40e 0000:02:00.0: type=19 seid=392 uplink=160 downlink=16
[ 98.452593] i40e 0000:02:00.0: type=17 seid=160 uplink=2 downlink=0
[ 98.458856] i40e 0000:02:00.0: type=19 seid=390 uplink=160 downlink=16
2) Add floating VEB
[root@cnb-03 net-next]# echo add relay > $CMD
[root@cnb-03 net-next]# dmesg -c
[ 122.745630] i40e 0000:02:00.0: added relay 162
[root@cnb-03 net-next]# echo dump switch > $CMD
[root@cnb-03 net-next]# dmesg -c
[ 136.650049] i40e 0000:02:00.0: header: 4 reported 4 total
[ 136.655466] i40e 0000:02:00.0: type=19 seid=392 uplink=160 downlink=16
[ 136.661994] i40e 0000:02:00.0: type=17 seid=160 uplink=2 downlink=0
[ 136.668264] i40e 0000:02:00.0: type=19 seid=390 uplink=160 downlink=16
[ 136.674787] i40e 0000:02:00.0: type=17 seid=162 uplink=0 downlink=0
3) Add VMDQ2 VSI to this new VEB
[root@cnb-03 net-next]# dmesg -c
[ 168.351763] i40e 0000:02:00.0: added VSI 394 to relay 162
[ 168.374652] enp2s0f0np0v0: NIC Link is Up, 40 Gbps Full Duplex, Flow Control: None
[root@cnb-03 net-next]# echo dump switch > $CMD
[root@cnb-03 net-next]# dmesg -c
[ 195.683204] i40e 0000:02:00.0: header: 5 reported 5 total
[ 195.688611] i40e 0000:02:00.0: type=19 seid=394 uplink=162 downlink=16
[ 195.695143] i40e 0000:02:00.0: type=17 seid=162 uplink=0 downlink=0
[ 195.701410] i40e 0000:02:00.0: type=19 seid=392 uplink=160 downlink=16
[ 195.707935] i40e 0000:02:00.0: type=17 seid=160 uplink=2 downlink=0
[ 195.714201] i40e 0000:02:00.0: type=19 seid=390 uplink=160 downlink=16
4) Try to delete the VEB
[root@cnb-03 net-next]# echo del relay 162 > $CMD
[root@cnb-03 net-next]# dmesg -c
[ 239.260901] i40e 0000:02:00.0: deleting relay 162
[ 239.265621] i40e 0000:02:00.0: can't remove VEB 162 with 1 VSIs left
5) Do PF reset and check switch status after rebuild
[root@cnb-03 net-next]# echo pfr > $CMD
[root@cnb-03 net-next]# echo dump switch > $CMD
[root@cnb-03 net-next]# dmesg -c
...
[ 272.333655] i40e 0000:02:00.0: header: 5 reported 5 total
[ 272.339066] i40e 0000:02:00.0: type=19 seid=394 uplink=162 downlink=16
[ 272.345599] i40e 0000:02:00.0: type=17 seid=162 uplink=0 downlink=0
[ 272.351862] i40e 0000:02:00.0: type=19 seid=392 uplink=160 downlink=16
[ 272.358387] i40e 0000:02:00.0: type=17 seid=160 uplink=2 downlink=0
[ 272.364654] i40e 0000:02:00.0: type=19 seid=390 uplink=160 downlink=16
6) Delete VSI and delete VEB
[ 297.199116] i40e 0000:02:00.0: deleting VSI 394
[ 299.807580] i40e 0000:02:00.0: deleting relay 162
[ 309.767905] i40e 0000:02:00.0: header: 3 reported 3 total
[ 309.773318] i40e 0000:02:00.0: type=19 seid=392 uplink=160 downlink=16
[ 309.779845] i40e 0000:02:00.0: type=17 seid=160 uplink=2 downlink=0
[ 309.786111] i40e 0000:02:00.0: type=19 seid=390 uplink=160 downlink=16
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Although the i40e supports so-called floating VEB (VEB without
an uplink connection to external network), this support is
broken. This functionality is currently unused (except debugfs)
but it will be used by subsequent series for switchdev mode
slow-path. Fix this by following:
1) Handle correctly floating VEB (VEB with uplink_seid == 0)
in i40e_reconstitute_veb() and look for owner VSI and
create it only for non-floating VEBs and also set bridge
mode only for such VEBs as the floating ones are using
always VEB mode.
2) Handle correctly floating VEB in i40e_veb_release() and
disallow its release when there are some VSIs. This is
different from regular VEB that have owner VSI that is
connected to VEB's uplink after VEB deletion by FW.
3) Fix i40e_add_veb() to handle 'vsi' that is NULL for floating
VEBs. For floating VEB use 0 for downlink SEID and 'true'
for 'default_port' parameters as per datasheet.
4) Fix 'add relay' command in i40e_dbg_command_write() to allow
to create floating VEB by 'add relay 0 0' or 'add relay'
Tested using debugfs:
1) Initial state
[root@host net-next]# echo dump switch > $CMD
[root@host net-next]# dmesg -c
[ 173.701286] i40e 0000:02:00.0: header: 3 reported 3 total
[ 173.706701] i40e 0000:02:00.0: type=19 seid=392 uplink=160 downlink=16
[ 173.713241] i40e 0000:02:00.0: type=17 seid=160 uplink=2 downlink=0
[ 173.719507] i40e 0000:02:00.0: type=19 seid=390 uplink=160 downlink=16
2) Add floating VEB
[root@host net-next]# CMD="/sys/kernel/debug/i40e/0000:02:00.0/command"
[root@host net-next]# echo add relay > $CMD
[root@host net-next]# dmesg -c
[ 245.551720] i40e 0000:02:00.0: added relay 162
[root@host net-next]# echo dump switch > $CMD
[root@host net-next]# dmesg -c
[ 276.984371] i40e 0000:02:00.0: header: 4 reported 4 total
[ 276.989779] i40e 0000:02:00.0: type=19 seid=392 uplink=160 downlink=16
[ 276.996302] i40e 0000:02:00.0: type=17 seid=160 uplink=2 downlink=0
[ 277.002569] i40e 0000:02:00.0: type=19 seid=390 uplink=160 downlink=16
[ 277.009091] i40e 0000:02:00.0: type=17 seid=162 uplink=0 downlink=0
3) Add VMDQ2 VSI to this new VEB
[root@host net-next]# echo add vsi 162 > $CMD
[root@host net-next]# dmesg -c
[ 332.314030] i40e 0000:02:00.0: added VSI 394 to relay 162
[ 332.337486] enp2s0f0np0v0: NIC Link is Up, 40 Gbps Full Duplex, Flow Control: None
[root@host net-next]# echo dump switch > $CMD
[root@host net-next]# dmesg -c
[ 387.284490] i40e 0000:02:00.0: header: 5 reported 5 total
[ 387.289904] i40e 0000:02:00.0: type=19 seid=394 uplink=162 downlink=16
[ 387.296446] i40e 0000:02:00.0: type=17 seid=162 uplink=0 downlink=0
[ 387.302708] i40e 0000:02:00.0: type=19 seid=392 uplink=160 downlink=16
[ 387.309234] i40e 0000:02:00.0: type=17 seid=160 uplink=2 downlink=0
[ 387.315500] i40e 0000:02:00.0: type=19 seid=390 uplink=160 downlink=16
4) Try to delete the VEB
[root@host net-next]# echo del relay 162 > $CMD
[root@host net-next]# dmesg -c
[ 428.749297] i40e 0000:02:00.0: deleting relay 162
[ 428.754011] i40e 0000:02:00.0: can't remove VEB 162 with 1 VSIs left
5) Do PF reset and check switch status after rebuild
[root@host net-next]# echo pfr > $CMD
[root@host net-next]# echo dump switch > $CMD
[root@host net-next]# dmesg -c
[ 738.056172] i40e 0000:02:00.0: header: 5 reported 5 total
[ 738.061577] i40e 0000:02:00.0: type=19 seid=394 uplink=162 downlink=16
[ 738.068104] i40e 0000:02:00.0: type=17 seid=162 uplink=0 downlink=0
[ 738.074367] i40e 0000:02:00.0: type=19 seid=392 uplink=160 downlink=16
[ 738.080892] i40e 0000:02:00.0: type=17 seid=160 uplink=2 downlink=0
[ 738.087160] i40e 0000:02:00.0: type=19 seid=390 uplink=160 downlink=16
6) Delete VSI and delete VEB
[root@host net-next]# echo del vsi 394 > $CMD
[root@host net-next]# echo del relay 162 > $CMD
[root@host net-next]# echo dump switch > $CMD
[root@host net-next]# dmesg -c
[ 1233.081126] i40e 0000:02:00.0: deleting VSI 394
[ 1239.345139] i40e 0000:02:00.0: deleting relay 162
[ 1244.886920] i40e 0000:02:00.0: header: 3 reported 3 total
[ 1244.892328] i40e 0000:02:00.0: type=19 seid=392 uplink=160 downlink=16
[ 1244.898853] i40e 0000:02:00.0: type=17 seid=160 uplink=2 downlink=0
[ 1244.905119] i40e 0000:02:00.0: type=19 seid=390 uplink=160 downlink=16
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add two helpers i40e_(veb|vsi)_get_by_seid() to find corresponding
VEB or VSI by their SEID value and use these helpers to replace
existing open-coded loops.
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Introduce i40e_for_each_vsi() and i40e_for_each_veb() helper
macros and use them to iterate relevant arrays.
Replace pattern:
for (i = 0; i < pf->num_alloc_vsi; i++)
by:
i40e_for_each_vsi(pf, i, vsi)
and pattern:
for (i = 0; i < I40E_MAX_VEB; i++)
by
i40e_for_each_veb(pf, i, veb)
These macros also check if array item pf->vsi[i] or pf->veb[i]
are not NULL and skip such items so we can remove redundant
checks from loop bodies.
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Use existing i40e_find_vsi_by_type() to find a VSI
associated with flow director.
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2024-02-12 (i40e)
This series contains updates to i40e driver only.
Ivan Vecera corrects the looping value used while waiting for queues to
be disabled as well as an incorrect mask being used for DCB
configuration.
Maciej resolves an issue related to XDP traffic; removing a double call to
i40e_pf_rxq_wait() and accounting for XDP rings when stopping rings.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Seth reported that on his side XDP traffic can not survive a round of
down/up against i40e interface. Dmesg output was telling us that we were
not able to disable the very first XDP ring. That was due to the fact
that in i40e_vsi_stop_rings() in a pre-work that is done before calling
i40e_vsi_wait_queues_disabled(), XDP Tx queues were not taken into the
account.
To fix this, let us distinguish between Rx and Tx queue boundaries and
take into the account XDP queues for Tx side.
Reported-by: Seth Forshee <sforshee@kernel.org>
Closes: https://lore.kernel.org/netdev/ZbkE7Ep1N1Ou17sA@do-x1extreme/
Fixes: 65662a8dcd ("i40e: Fix logic of disabling queues")
Tested-by: Seth Forshee <sforshee@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Reviewed-by: Ivan Vecera <ivecera@redhat.com>
Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com> (A Contingent Worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently, when interface is being brought down and
i40e_vsi_stop_rings() is called, i40e_pf_rxq_wait() is called two times,
which is wrong. To showcase this scenario, simplified call stack looks
as follows:
i40e_vsi_stop_rings()
i40e_control wait rx_q()
i40e_control_rx_q()
i40e_pf_rxq_wait()
i40e_vsi_wait_queues_disabled()
i40e_pf_rxq_wait() // redundant call
To fix this, let us s/i40e_control_wait_rx_q/i40e_control_rx_q within
i40e_vsi_stop_rings().
Fixes: 65662a8dcd ("i40e: Fix logic of disabling queues")
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Reviewed-by: Ivan Vecera <ivecera@redhat.com>
Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com> (A Contingent Worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Mask used for clearing PRTDCB_RETSTCC register in function
i40e_dcb_hw_rx_ets_bw_config() is incorrect as there is used
define I40E_PRTDCB_RETSTCC_ETSTC_SHIFT instead of define
I40E_PRTDCB_RETSTCC_ETSTC_MASK.
The PRTDCB_RETSTCC register is used to configure whether ETS
or strict priority is used as TSA in Rx for particular TC.
In practice it means that once the register is set to use ETS
as TSA then it is not possible to switch back to strict priority
without CoreR reset.
Fix the value in the clearing mask.
Fixes: 90bc8e003b ("i40e: Add hardware configuration for software based DCB")
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The function i40e_pf_wait_queues_disabled() iterates all PF's VSIs
up to 'pf->hw.func_caps.num_vsis' but this is incorrect because
the real number of VSIs can be up to 'pf->num_alloc_vsi' that
can be higher. Fix this loop.
Fixes: 69129dc39f ("i40e: Modify Tx disable wait flow in case of DCB reconfiguration")
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently when PF administratively sets VF's MAC address and the VF
is put down (VF tries to delete all MACs) then the MAC is removed
from MAC filters and primary VF MAC is zeroed.
Do not allow untrusted VF to remove primary MAC when it was set
administratively by PF.
Reproducer:
1) Create VF
2) Set VF interface up
3) Administratively set the VF's MAC
4) Put VF interface down
[root@host ~]# echo 1 > /sys/class/net/enp2s0f0/device/sriov_numvfs
[root@host ~]# ip link set enp2s0f0v0 up
[root@host ~]# ip link set enp2s0f0 vf 0 mac fe:6c:b5:da:c7:7d
[root@host ~]# ip link show enp2s0f0
23: enp2s0f0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP mode DEFAULT group default qlen 1000
link/ether 3c:ec:ef:b7:dd:04 brd ff:ff:ff:ff:ff:ff
vf 0 link/ether fe:6c:b5:da:c7:7d brd ff:ff:ff:ff:ff:ff, spoof checking on, link-state auto, trust off
[root@host ~]# ip link set enp2s0f0v0 down
[root@host ~]# ip link show enp2s0f0
23: enp2s0f0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP mode DEFAULT group default qlen 1000
link/ether 3c:ec:ef:b7:dd:04 brd ff:ff:ff:ff:ff:ff
vf 0 link/ether 00:00:00:00:00:00 brd ff:ff:ff:ff:ff:ff, spoof checking on, link-state auto, trust off
Fixes: 700bbf6c1f ("i40e: allow VF to remove any MAC filter")
Fixes: ceb29474bb ("i40e: Add support for VF to specify its primary MAC address")
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20240208180335.1844996-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Cross-merge networking fixes after downstream PR.
No conflicts.
Adjacent changes:
drivers/net/ethernet/stmicro/stmmac/common.h
38cc3c6dcc ("net: stmmac: protect updates of 64-bit statistics counters")
fd5a6a7131 ("net: stmmac: est: Per Tx-queue error count for HLBF")
c5c3e1bfc9 ("net: stmmac: Offload queueMaxSDU from tc-taprio")
drivers/net/wireless/microchip/wilc1000/netdev.c
c901388028 ("wifi: fill in MODULE_DESCRIPTION()s for wilc1000")
328efda22a ("wifi: wilc1000: do not realloc workqueue everytime an interface is added")
net/unix/garbage.c
11498715f2 ("af_unix: Remove io_uring code for GC.")
1279f9d9de ("af_unix: Call kfree_skb() for dead unix_(sk)->oob_skb in GC.")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The kernel build regressions/improvements email contained a couple of
issues with old compilers (in fact all the reports were on different
architectures, but all gcc 5.5) and the FIELD_PREP() and FIELD_GET()
conversions. They're all because an integer #define that should have
been declared as unsigned, was shifted to the point that it could set
the sign bit.
The fix just involves making sure the defines use the "U" identifier on
the constants to make sure they're unsigned. Should make the checkers
happier.
Confirmed with objdump before/after that there is no change to the
binaries.
Issues were reported as follows:
./drivers/net/ethernet/intel/ice/ice_base.c:238:7: note: in expansion of macro 'FIELD_GET'
(FIELD_GET(GLINT_CTL_ITR_GRAN_25_M, regval) == ICE_ITR_GRAN_US))
^
./include/linux/compiler_types.h:435:38: error: call to '__compiletime_assert_1093' declared with attribute error: FIELD_GET: mask is not constant
drivers/net/ethernet/intel/ice/ice_nvm.c:709:16: note: in expansion of macro ‘FIELD_GET’
orom->major = FIELD_GET(ICE_OROM_VER_MASK, combo_ver);
^
./include/linux/compiler_types.h:435:38: error: call to ‘__compiletime_assert_796’ declared with attribute error: FIELD_GET: mask is not constant
drivers/net/ethernet/intel/ice/ice_common.c:945:18: note: in expansion of macro ‘FIELD_GET’
u8 max_agg_bw = FIELD_GET(GL_PWR_MODE_CTL_CAR_MAX_BW_M,
^
./include/linux/compiler_types.h:435:38: error: call to ‘__compiletime_assert_420’ declared with attribute error: FIELD_GET: mask is not constant
drivers/net/ethernet/intel/i40e/i40e_dcb.c:458:8: note: in expansion of macro ‘FIELD_GET’
oui = FIELD_GET(I40E_LLDP_TLV_OUI_MASK, ouisubtype);
^
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Closes: https://lore.kernel.org/lkml/d03e90ca-8485-4d1b-5ec1-c3398e0e8da@linux-m68k.org/ #i40e #ice
Fixes: 62589808d7 ("i40e: field get conversion")
Fixes: 5a259f8e0b ("ice: field get conversion")
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Link: https://lore.kernel.org/r/20240206022906.2194214-1-jesse.brandeburg@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This is in preparation of using the existing names for linkmode
bitmaps.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to pass EEE link modes beyond bit 32 to userspace we have to
complement the 32 bit bitmaps in struct ethtool_eee with linkmode
bitmaps. Therefore, similar to ethtool_link_settings and
ethtool_link_ksettings, add a struct ethtool_keee. In a first step
it's an identical copy of ethtool_eee. This patch simply does a
s/ethtool_eee/ethtool_keee/g for all users.
No functional change intended.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that i40e driver correctly sets up frag_size in xdp_rxq_info, let us
make it work for ZC multi-buffer as well. i40e_ring::rx_buf_len for ZC
is being set via xsk_pool_get_rx_frame_size() and this needs to be
propagated up to xdp_rxq_info.
Fixes: 1c9ba9c146 ("i40e: xsk: add RX multi-buffer support")
Acked-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Link: https://lore.kernel.org/r/20240124191602.566724-12-maciej.fijalkowski@intel.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
i40e support XDP multi-buffer so it is supposed to use
__xdp_rxq_info_reg() instead of xdp_rxq_info_reg() and set the
frag_size. It can not be simply converted at existing callsite because
rx_buf_len could be un-initialized, so let us register xdp_rxq_info
within i40e_configure_rx_ring(), which happen to be called with already
initialized rx_buf_len value.
Commit 5180ff1364 ("i40e: use int for i40e_status") converted 'err' to
int, so two variables to deal with return codes are not needed within
i40e_configure_rx_ring(). Remove 'ret' and use 'err' to handle status
from xdp_rxq_info registration.
Fixes: e213ced19b ("i40e: add support for XDP multi-buffer Rx")
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Link: https://lore.kernel.org/r/20240124191602.566724-11-maciej.fijalkowski@intel.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Ice and i40e ZC drivers currently set offset of a frag within
skb_shared_info to 0, which is incorrect. xdp_buffs that come from
xsk_buff_pool always have 256 bytes of a headroom, so they need to be
taken into account to retrieve xdp_buff::data via skb_frag_address().
Otherwise, bpf_xdp_frags_increase_tail() would be starting its job from
xdp_buff::data_hard_start which would result in overwriting existing
payload.
Fixes: 1c9ba9c146 ("i40e: xsk: add RX multi-buffer support")
Fixes: 1bbc04de60 ("ice: xsk: add RX multi-buffer support")
Acked-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Link: https://lore.kernel.org/r/20240124191602.566724-8-maciej.fijalkowski@intel.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
XDP programs can shrink packets by calling the bpf_xdp_adjust_tail()
helper function. For multi-buffer packets this may lead to reduction of
frag count stored in skb_shared_info area of the xdp_buff struct. This
results in issues with the current handling of XDP_PASS and XDP_DROP
cases.
For XDP_PASS, currently skb is being built using frag count of
xdp_buffer before it was processed by XDP prog and thus will result in
an inconsistent skb when frag count gets reduced by XDP prog. To fix
this, get correct frag count while building the skb instead of using
pre-obtained frag count.
For XDP_DROP, current page recycling logic will not reuse the page but
instead will adjust the pagecnt_bias so that the page can be freed. This
again results in inconsistent behavior as the page refcnt has already
been changed by the helper while freeing the frag(s) as part of
shrinking the packet. To fix this, only adjust pagecnt_bias for buffers
that are stillpart of the packet post-xdp prog run.
Fixes: e213ced19b ("i40e: add support for XDP multi-buffer Rx")
Reported-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Tirthendu Sarkar <tirthendu.sarkar@intel.com>
Link: https://lore.kernel.org/r/20240124191602.566724-6-maciej.fijalkowski@intel.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
XDP multi-buffer support introduced XDP_FLAGS_HAS_FRAGS flag that is
used by drivers to notify data path whether xdp_buff contains fragments
or not. Data path looks up mentioned flag on first buffer that occupies
the linear part of xdp_buff, so drivers only modify it there. This is
sufficient for SKB and XDP_DRV modes as usually xdp_buff is allocated on
stack or it resides within struct representing driver's queue and
fragments are carried via skb_frag_t structs. IOW, we are dealing with
only one xdp_buff.
ZC mode though relies on list of xdp_buff structs that is carried via
xsk_buff_pool::xskb_list, so ZC data path has to make sure that
fragments do *not* have XDP_FLAGS_HAS_FRAGS set. Otherwise,
xsk_buff_free() could misbehave if it would be executed against xdp_buff
that carries a frag with XDP_FLAGS_HAS_FRAGS flag set. Such scenario can
take place when within supplied XDP program bpf_xdp_adjust_tail() is
used with negative offset that would in turn release the tail fragment
from multi-buffer frame.
Calling xsk_buff_free() on tail fragment with XDP_FLAGS_HAS_FRAGS would
result in releasing all the nodes from xskb_list that were produced by
driver before XDP program execution, which is not what is intended -
only tail fragment should be deleted from xskb_list and then it should
be put onto xsk_buff_pool::free_list. Such multi-buffer frame will never
make it up to user space, so from AF_XDP application POV there would be
no traffic running, however due to free_list getting constantly new
nodes, driver will be able to feed HW Rx queue with recycled buffers.
Bottom line is that instead of traffic being redirected to user space,
it would be continuously dropped.
To fix this, let us clear the mentioned flag on xsk_buff_pool side
during xdp_buff initialization, which is what should have been done
right from the start of XSK multi-buffer support.
Fixes: 1bbc04de60 ("ice: xsk: add RX multi-buffer support")
Fixes: 1c9ba9c146 ("i40e: xsk: add RX multi-buffer support")
Fixes: 24ea50127e ("xsk: support mbuf on ZC RX")
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Link: https://lore.kernel.org/r/20240124191602.566724-3-maciej.fijalkowski@intel.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Commit 56df345917 ("i40e: Remove circular header dependencies and fix
headers") redistributed a number of includes from one large header file
to the locations they were needed. In some environments, types.h is not
included and causing compile issues. The driver should not rely on
implicit inclusion from other locations; explicitly include it to these
files.
Snippet of issue. Entire log can be seen through the Closes: link.
In file included from drivers/net/ethernet/intel/i40e/i40e_diag.h:7,
from drivers/net/ethernet/intel/i40e/i40e_diag.c:4:
drivers/net/ethernet/intel/i40e/i40e_adminq_cmd.h:33:9: error: unknown type name '__le16'
33 | __le16 flags;
| ^~~~~~
drivers/net/ethernet/intel/i40e/i40e_adminq_cmd.h:34:9: error: unknown type name '__le16'
34 | __le16 opcode;
| ^~~~~~
...
drivers/net/ethernet/intel/i40e/i40e_diag.h:22:9: error: unknown type name 'u32'
22 | u32 elements; /* number of elements if array */
| ^~~
drivers/net/ethernet/intel/i40e/i40e_diag.h:23:9: error: unknown type name 'u32'
23 | u32 stride; /* bytes between each element */
Reported-by: Martin Zaharinov <micron10@gmail.com>
Closes: https://lore.kernel.org/netdev/21BBD62A-F874-4E42-B347-93087EEA8126@gmail.com/
Fixes: 56df345917 ("i40e: Remove circular header dependencies and fix headers")
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Arpana Arland <arpanax.arland@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20240117172534.3555162-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2024-01-03 (i40e, ice, igc)
This series contains updates to i40e, ice, and igc drivers.
Ke Xiao fixes use after free for unicast filters on i40e.
Andrii restores VF MSI-X flag after PCI reset on i40e.
Paul corrects admin queue link status structure to fulfill firmware
expectations for ice.
Rodrigo Cataldo corrects value used for hicredit calculations on igc.
* '40GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
igc: Fix hicredit calculation
ice: fix Get link status data length
i40e: Restore VF MSI-X state during PCI reset
i40e: fix use-after-free in i40e_aqc_add_filters()
====================
Link: https://lore.kernel.org/r/20240103193254.822968-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
During a PCI FLR the MSI-X Enable flag in the VF PCI MSI-X capability
register will be cleared. This can lead to issues when a VF is
assigned to a VM because in these cases the VF driver receives no
indication of the PF PCI error/reset and additionally it is incapable
of restoring the cleared flag in the hypervisor configuration space
without fully reinitializing the driver interrupt functionality.
Since the VF driver is unable to easily resolve this condition on its own,
restore the VF MSI-X flag during the PF PCI reset handling.
Fixes: 19b7960b2d ("i40e: implement split PCI error reset handler")
Co-developed-by: Karen Ostrowska <karen.ostrowska@intel.com>
Signed-off-by: Karen Ostrowska <karen.ostrowska@intel.com>
Co-developed-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Andrii Staikov <andrii.staikov@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Commit 3116f59c12 ("i40e: fix use-after-free in
i40e_sync_filters_subtask()") avoided use-after-free issues,
by increasing refcount during update the VSI filter list to
the HW. However, it missed the unicast situation.
When deleting an unicast FDB entry, the i40e driver will release
the mac_filter, and i40e_service_task will concurrently request
firmware to add the mac_filter, which will lead to the following
use-after-free issue.
Fix again for both netdev->uc and netdev->mc.
BUG: KASAN: use-after-free in i40e_aqc_add_filters+0x55c/0x5b0 [i40e]
Read of size 2 at addr ffff888eb3452d60 by task kworker/8:7/6379
CPU: 8 PID: 6379 Comm: kworker/8:7 Kdump: loaded Tainted: G
Workqueue: i40e i40e_service_task [i40e]
Call Trace:
dump_stack+0x71/0xab
print_address_description+0x6b/0x290
kasan_report+0x14a/0x2b0
i40e_aqc_add_filters+0x55c/0x5b0 [i40e]
i40e_sync_vsi_filters+0x1676/0x39c0 [i40e]
i40e_service_task+0x1397/0x2bb0 [i40e]
process_one_work+0x56a/0x11f0
worker_thread+0x8f/0xf40
kthread+0x2a0/0x390
ret_from_fork+0x1f/0x40
Allocated by task 21948:
kasan_kmalloc+0xa6/0xd0
kmem_cache_alloc_trace+0xdb/0x1c0
i40e_add_filter+0x11e/0x520 [i40e]
i40e_addr_sync+0x37/0x60 [i40e]
__hw_addr_sync_dev+0x1f5/0x2f0
i40e_set_rx_mode+0x61/0x1e0 [i40e]
dev_uc_add_excl+0x137/0x190
i40e_ndo_fdb_add+0x161/0x260 [i40e]
rtnl_fdb_add+0x567/0x950
rtnetlink_rcv_msg+0x5db/0x880
netlink_rcv_skb+0x254/0x380
netlink_unicast+0x454/0x610
netlink_sendmsg+0x747/0xb00
sock_sendmsg+0xe2/0x120
__sys_sendto+0x1ae/0x290
__x64_sys_sendto+0xdd/0x1b0
do_syscall_64+0xa0/0x370
entry_SYSCALL_64_after_hwframe+0x65/0xca
Freed by task 21948:
__kasan_slab_free+0x137/0x190
kfree+0x8b/0x1b0
__i40e_del_filter+0x116/0x1e0 [i40e]
i40e_del_mac_filter+0x16c/0x300 [i40e]
i40e_addr_unsync+0x134/0x1b0 [i40e]
__hw_addr_sync_dev+0xff/0x2f0
i40e_set_rx_mode+0x61/0x1e0 [i40e]
dev_uc_del+0x77/0x90
rtnl_fdb_del+0x6a5/0x860
rtnetlink_rcv_msg+0x5db/0x880
netlink_rcv_skb+0x254/0x380
netlink_unicast+0x454/0x610
netlink_sendmsg+0x747/0xb00
sock_sendmsg+0xe2/0x120
__sys_sendto+0x1ae/0x290
__x64_sys_sendto+0xdd/0x1b0
do_syscall_64+0xa0/0x370
entry_SYSCALL_64_after_hwframe+0x65/0xca
Fixes: 3116f59c12 ("i40e: fix use-after-free in i40e_sync_filters_subtask()")
Fixes: 41c445ff0f ("i40e: main driver core")
Signed-off-by: Ke Xiao <xiaoke@sangfor.com.cn>
Signed-off-by: Ding Hui <dinghui@sangfor.com.cn>
Cc: Di Zhu <zhudi2@huawei.com>
Reviewed-by: Jan Sokolowski <jan.sokolowski@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Although it does not seem to have any untoward side-effects,
the use of ';' to separate to assignments seems more appropriate than ','.
Flagged by clang-17 -Wcomma
No functional change intended.
Compile tested only.
Signed-off-by: Simon Horman <horms@kernel.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently, if a VF is disabled using the
'ip link set dev $ETHX vf $VF_NUM state disable' command, the VF is still
able to receive traffic.
Fix the behavior of the 'ip link set dev $ETHX vf $VF_NUM state disable'
to completely shutdown the VF's queues making it entirely disabled and
not able to receive or send any traffic.
Modify the behavior of the 'ip link set $ETHX vf $VF_NUM state enable'
command to make a VF do reinitialization bringing the queues back up.
Co-developed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Jan Sokolowski <jan.sokolowski@intel.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Andrii Staikov <andrii.staikov@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Prevent VF from configuring filters with unsupported actions or use
REDIRECT action with invalid tc number. Current checks could cause
out of bounds access on PF side.
Fixes: e284fc2804 ("i40e: Add and delete cloud filter")
Reviewed-by: Andrii Staikov <andrii.staikov@intel.com>
Signed-off-by: Sudheer Mogilappagari <sudheer.mogilappagari@intel.com>
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Bharathi Sreenivas <bharathi.sreenivas@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tony Nguyen says:
====================
intel: use bitfield operations
Jesse Brandeburg says:
After repeatedly getting review comments on new patches, and sporadic
patches to fix parts of our drivers, we should just convert the Intel code
to use FIELD_PREP() and FIELD_GET(). It's then "common" in the code and
hopefully future change-sets will see the context and do-the-right-thing.
This conversion was done with a coccinelle script which is mentioned in the
commit messages. Generally there were only a couple conversions that were
"undone" after the automatic changes because they tried to convert a
non-contiguous mask.
Patch 1 is required at the beginning of this series to fix a "forever"
issue in the e1000e driver that fails the compilation test after conversion
because the shift / mask was out of range.
The second patch just adds all the new #includes in one go.
The patch titled: "ice: fix pre-shifted bit usage" is needed to allow the
use of the FIELD_* macros and fix up the unexpected "shifts included"
defines found while creating this series.
The rest are the conversion to use FIELD_PREP()/FIELD_GET(), and the
occasional leXX_{get,set,encode}_bits() call, as suggested by Alex.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor the i40e driver to use FIELD_GET() for mask and shift reads,
which reduces lines of code and adds clarity of intent.
This code was generated by the following coccinelle/spatch script and
then manually repaired.
While making one of the conversions, an if() check was inverted to
return early and avoid un-necessary indentation of the remainder of the
function. In some other cases a stack variable was moved inside the
block where it was used while doing cleanups/review.
A couple places were changed to use le16_get_bits() instead of FIELD_GET
with a le16_to_cpu combination.
@get@
constant shift,mask;
metavariable type T;
expression a;
@@
-(((T)(a) & mask) >> shift)
+FIELD_GET(mask, a)
and applied via:
spatch --sp-file field_prep.cocci --in-place --dir \
drivers/net/ethernet/intel/
Cc: Julia Lawall <Julia.Lawall@inria.fr>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Refactor i40e driver to use FIELD_PREP(), which reduces lines of code
and adds clarity of intent.
This code was generated by the following coccinelle/spatch script and
then manually repaired.
Refactor one function with multiple if's to return quickly to make lines
fit in 80 columns.
@prep2@
constant shift,mask;
type T;
expression a;
@@
-(((T)(a) << shift) & mask)
+FIELD_PREP(mask, a)
@prep@
constant shift,mask;
type T;
expression a;
@@
-((T)((a) << shift) & mask)
+FIELD_PREP(mask, a)
Cc: Julia Lawall <Julia.Lawall@inria.fr>
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
This series is introducing the use of FIELD_GET and FIELD_PREP which
requires bitfield.h to be included. Fix all the includes in this one
change, and rearrange includes into alphabetical order to ease
readability and future maintenance.
virtchnl.h and it's usage was modified to have it's own includes as it
should. This required including bits.h for virtchnl.h.
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Since we never support this feature for I40E driver, we don't have to
display the value when using 'ethtool -c eth0'.
Before this patch applied, the rx-frames-irq is 256 which is consistent
with tx-frames-irq. Apparently it could mislead users.
Signed-off-by: Jason Xing <kernelxing@tencent.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20231213184406.1306602-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The get/set_rxfh ethtool ops currently takes the rxfh (RSS) parameters
as direct function arguments. This will force us to change the API (and
all drivers' functions) every time some new parameters are added.
This is part 1/2 of the fix, as suggested in [1]:
- First simplify the code by always providing a pointer to all params
(indir, key and func); the fact that some of them may be NULL seems
like a weird historic thing or a premature optimization.
It will simplify the drivers if all pointers are always present.
- Then make the functions take a dev pointer, and a pointer to a
single struct wrapping all arguments. The set_* should also take
an extack.
Link: https://lore.kernel.org/netdev/20231121152906.2dd5f487@kernel.org/ [1]
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Suggested-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Link: https://lore.kernel.org/r/20231213003321.605376-2-ahmed.zaki@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
ST code value for clause 45 that has been changed by
commit 8196b5fd6c ("i40e: Refactor I40E_MDIO_CLAUSE* macros")
is currently wrong.
The mentioned commit refactored ..MDIO_CLAUSE??_STCODE_MASK so
their value is the same for both clauses. The value is correct
for clause 22 but not for clause 45.
Fix the issue by adding a parameter to I40E_GLGEN_MSCA_STCODE_MASK
macro that specifies required value.
Fixes: 8196b5fd6c ("i40e: Refactor I40E_MDIO_CLAUSE* macros")
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
This patch converts some basic cases of ethtool_sprintf() to
ethtool_puts().
The conversions are used in cases where ethtool_sprintf() was being used
with just two arguments:
| ethtool_sprintf(&data, buffer[i].name);
or when it's used with format string: "%s"
| ethtool_sprintf(&data, "%s", buffer[i].name);
which both now become:
| ethtool_puts(&data, buffer[i].name);
Signed-off-by: Justin Stitt <justinstitt@google.com>
Reviewed-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 3a2c6ced90 ("i40e: Add a check to see if MFS is set") added
a warning message that reports unexpected size of port's MFS (max
frame size) value. This message use for the port number local
variable 'i' that is wrong.
In i40e_probe() this 'i' variable is used only to iterate VSIs
to find FDIR VSI:
<code>
...
/* if FDIR VSI was set up, start it now */
for (i = 0; i < pf->num_alloc_vsi; i++) {
if (pf->vsi[i] && pf->vsi[i]->type == I40E_VSI_FDIR) {
i40e_vsi_open(pf->vsi[i]);
break;
}
}
...
</code>
So the warning message use for the port number index of FDIR VSI
if this exists or pf->num_alloc_vsi if not.
Fix the message by using 'pf->hw.port' for the port number.
Fixes: 3a2c6ced90 ("i40e: Add a check to see if MFS is set")
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Fields 'head', 'tail', 'len', 'bah' and 'bal' in i40e_adminq_ring
are used to store register offsets. These offsets are initialized
and remains constant so there is no need to store them in the
i40e_adminq_ring structure.
Remove these fields from i40e_adminq_ring and use register offset
constants instead. Remove i40e_adminq_init_regs() that originally
stores these constants into these fields.
Finally improve i40e_check_asq_alive() that assumes that
non-zero value of hw->aq.asq.len indicates fully initialized
AdminQ send queue. Replace it by check for non-zero value
of field hw->aq.asq.count that is non-zero when the sending
queue is initialized and is zeroed during shutdown of
the queue.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The i40e driver does not handle its VF device types so there
is no need to keep AdminQ register definitions for such
device types. Remove them.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Removed fields:
.fc_autoneg_status
Since commit c56999f948 ("i40e/i40evf: Add set_fc and init of
FC settings") write-only and otherwise unused
.eeprom_version
Write-only and otherwise unused
.atr_sample_rate
Has only one possible value (I40E_DEFAULT_ATR_SAMPLE_RATE). Remove
it and replace its occurrences by I40E_DEFAULT_ATR_SAMPLE_RATE
.adminq_work_limit
Has only one possible value (I40E_AQ_WORK_LIMIT). Remove it and
replace its occurrences by I40E_AQ_WORK_LIMIT
.tx_sluggish_count
Unused, never written
.pf_seid
Used to store VSI downlink seid and it is referenced only once
in the same codepath. There is no need to save it into i40e_pf.
Remove it and use downlink_seid directly in the mentioned log
message.
.instance
Write only. Remove it as well as ugly static local variable
'pfs_found' in i40e_probe.
.int_policy
.switch_kobj
.ptp_pps_work
.ptp_extts1_work
.ptp_pps_start
.pps_delay
.ptp_pin
.override_q_count
All these unused at all
Prior the patch:
pahole -Ci40e_pf drivers/net/ethernet/intel/i40e/i40e.ko | tail -5
/* size: 5368, cachelines: 84, members: 127 */
/* sum members: 5297, holes: 20, sum holes: 71 */
/* paddings: 6, sum paddings: 19 */
/* last cacheline: 56 bytes */
};
After the patch:
pahole -Ci40e_pf drivers/net/ethernet/intel/i40e/i40e.ko | tail -5
/* size: 4976, cachelines: 78, members: 112 */
/* sum members: 4905, holes: 17, sum holes: 71 */
/* paddings: 6, sum paddings: 19 */
/* last cacheline: 48 bytes */
};
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
If a VF tries to add unsupported cloud filter through virtchnl
then i40e_add_del_cloud_filter(_big_buf) returns -ENOTSUPP but
this error code is stored in 'ret' instead of 'aq_ret' that
is used as error code sent back to VF. In this scenario where
one of the mentioned functions fails the value of 'aq_ret'
is zero so the VF will incorrectly receive a 'success'.
Use 'aq_ret' to store return value and remove 'ret' local
variable. Additionally fix the issue when filter allocation
fails, in this case no notification is sent back to the VF.
Fixes: e284fc2804 ("i40e: Add and delete cloud filter")
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20231121211338.3348677-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
From commit 9eed69a914 ("i40e: Drop FCoE code from core driver files")
the field i40e_mac_info.san_addr is unused (never filled).
The field i40e_mac_info.max_fcoeq is unused from the beginning.
Remove both.
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Co-developed-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20231113231047.548659-16-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The i40e_hw.mac.type cannot to be equal to I40E_MAC_VF or
I40E_MAC_X722_VF so remove helper i40e_is_vf(), simplify
i40e_adminq_init_regs() and remove enums for these VF MAC types.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20231113231047.548659-14-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use new helpers to check versions of running FW and provided
AQ API to make the code more readable.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20231113231047.548659-13-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add another helper functions that will be used by subsequent
patch to refactor existing open-coded checks whether the version
of running firmware and AdminQ API is recent enough to provide
certain capabilities.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20231113231047.548659-12-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
