The ASTDP transmitter sometimes takes up to 1 second for enabling the
video signal, while the timeout is only 200 msec. This results in a
kernel error message. Increase the timeout to 1 second. An example
of the error message is shown below.
[ 697.084433] ------------[ cut here ]------------
[ 697.091115] ast 0000:02:00.0: [drm] drm_WARN_ON(!__ast_dp_wait_enable(ast, enabled))
[ 697.091233] WARNING: CPU: 1 PID: 160 at drivers/gpu/drm/ast/ast_dp.c:232 ast_dp_set_enable+0x123/0x140 [ast]
[...]
[ 697.272469] RIP: 0010:ast_dp_set_enable+0x123/0x140 [ast]
[...]
[ 697.415283] Call Trace:
[ 697.420727] <TASK>
[ 697.425908] ? show_trace_log_lvl+0x196/0x2c0
[ 697.433304] ? show_trace_log_lvl+0x196/0x2c0
[ 697.440693] ? drm_atomic_helper_commit_modeset_enables+0x30a/0x470
[ 697.450115] ? ast_dp_set_enable+0x123/0x140 [ast]
[ 697.458059] ? __warn.cold+0xaf/0xca
[ 697.464713] ? ast_dp_set_enable+0x123/0x140 [ast]
[ 697.472633] ? report_bug+0x134/0x1d0
[ 697.479544] ? handle_bug+0x58/0x90
[ 697.486127] ? exc_invalid_op+0x13/0x40
[ 697.492975] ? asm_exc_invalid_op+0x16/0x20
[ 697.500224] ? preempt_count_sub+0x14/0xc0
[ 697.507473] ? ast_dp_set_enable+0x123/0x140 [ast]
[ 697.515377] ? ast_dp_set_enable+0x123/0x140 [ast]
[ 697.523227] drm_atomic_helper_commit_modeset_enables+0x30a/0x470
[ 697.532388] drm_atomic_helper_commit_tail+0x58/0x90
[ 697.540400] ast_mode_config_helper_atomic_commit_tail+0x30/0x40 [ast]
[ 697.550009] commit_tail+0xfe/0x1d0
[ 697.556547] drm_atomic_helper_commit+0x198/0x1c0
This is a cosmetical problem. Enabling the video signal still works
even with the error message. The problem has always been present, but
only recent versions of the ast driver warn about missing the timeout.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Fixes: 4e29cc7c5c ("drm/ast: astdp: Replace ast_dp_set_on_off()")
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Jocelyn Falempe <jfalempe@redhat.com>
Cc: Dave Airlie <airlied@redhat.com>
Cc: dri-devel@lists.freedesktop.org
Cc: <stable@vger.kernel.org> # v6.13+
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250127134423.84266-1-tzimmermann@suse.de
The header drm_print.h uses members of struct drm_device pointers, as
such, it should include drm_device.h to let the compiler know the full
type definition.
Without such include, users of drm_print.h that don't explicitly need
drm_device.h would bump into build errors and be forced to include the
latter.
Signed-off-by: Gustavo Sousa <gustavo.sousa@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250121210935.84357-1-gustavo.sousa@intel.com
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
We added some locking to this function, but accidentally forgot to unlock
if zynqmp_dp_mode_configure() failed. Use a guard lock to fix it.
Fixes: a7d5eeaa57 ("drm: zynqmp_dp: Add locking")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Sean Anderson <sean.anderson@linux.dev>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/b4042bd9-c943-4738-a2e1-8647259137c6@stanley.mountain
In the combination of DRM_KMS_HELPER=m, DRM_GEM_SHMEM_HELPER=y, DRM_FBDEV_EMULATION=y,
The shmem code fails to link against the KMS helpers:
x86_64-linux-ld: vmlinux.o: in function `drm_fbdev_shmem_driver_fbdev_probe':
(.text+0xeec601): undefined reference to `drm_fb_helper_alloc_info'
x86_64-linux-ld: (.text+0xeec633): undefined reference to `drm_fb_helper_fill_info'
x86_64-linux-ld: vmlinux.o: in function `drm_fbdev_shmem_get_page':
drm_fbdev_shmem.c:(.text+0xeec7d2): undefined reference to `drm_gem_fb_get_obj'
x86_64-linux-ld: vmlinux.o: in function `drm_fbdev_shmem_fb_mmap':
drm_fbdev_shmem.c:(.text+0xeec9f6): undefined reference to `drm_gem_fb_get_obj'
x86_64-linux-ld: vmlinux.o: in function `drm_fbdev_shmem_defio_imageblit':
(.rodata+0x5b2288): undefined reference to `drm_fb_helper_check_var'
x86_64-linux-ld: (.rodata+0x5b2290): undefined reference to `drm_fb_helper_set_par'
This can happen for a number of device drivers that select DRM_GEM_SHMEM_HELPER
without also selecting DRM_KMS_HELPER. To work around this, add another select
that forces DRM_KMS_HELPER to be built-in rather than a loadable module, but
only if FBDEV emulation is also enabled. DRM_TTM_HELPER and DRM_GEM_DMA_HELPER
look like they have the same problem in theory even if there is no possible
configuration that shows it. For consistency, do the same change to those.
Closes: https://lore.kernel.org/all/20250121-greedy-flounder-of-abundance-4d2ee8-mkl@pengutronix.de
Reported-by: Marc Kleine-Budde <mkl@pengutronix.de>
Tested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20250122090211.3161186-1-arnd@kernel.org
When testing on my tiled display, initially the tiled display is
detected correctly:
[90376.523692] xe 0000:67:00.0: [drm:drm_client_firmware_config.isra.0 [drm]] fallback: Not all outputs enabled
[90376.523713] xe 0000:67:00.0: [drm:drm_client_firmware_config.isra.0 [drm]] Enabled: 0, detected: 2
...
[90376.523967] xe 0000:67:00.0: [drm:drm_client_modeset_probe [drm]] [CRTC:82:pipe A] desired mode 1920x2160 set (1920,0)
[90376.524020] xe 0000:67:00.0: [drm:drm_client_modeset_probe [drm]] [CRTC:134:pipe B] desired mode 1920x2160 set (0,0)
But then, when modes have been set:
[90379.729525] xe 0000:67:00.0: [drm:drm_client_firmware_config.isra.0 [drm]] [CONNECTOR:287:DP-4] on [CRTC:82:pipe A]: 1920x2160
[90379.729640] xe 0000:67:00.0: [drm:drm_client_firmware_config.isra.0 [drm]] [CONNECTOR:289:DP-5] on [CRTC:134:pipe B]: 1920x2160
...
[90379.730036] xe 0000:67:00.0: [drm:drm_client_modeset_probe [drm]] [CRTC:82:pipe A] desired mode 1920x2160 set (0,0)
[90379.730124] xe 0000:67:00.0: [drm:drm_client_modeset_probe [drm]] [CRTC:134:pipe B] desired mode 1920x2160 set (0,0)
Call drm_client_get_tile_offsets() in drm_client_firmware_config() as
well, to ensure that the offset is set correctly.
This has to be done as a separate pass, as the tile order may not be
equal to the drm connector order.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20250116142825.3933-2-dev@lankhorst.se
Signed-off-by: Maarten Lankhorst <dev@lankhorst.se>
Cc: <stable@vger.kernel.org>
Tiled displays have a different x/y offset to begin with. Instead of
attempting to remember this, just apply a delta instead.
This fixes the first tile being duplicated on other tiles when vt
switching.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20250116142825.3933-1-dev@lankhorst.se
Signed-off-by: Maarten Lankhorst <dev@lankhorst.se>
Cc: <stable@vger.kernel.org>
If devm_i2c_new_dummy_device() fails then we were supposed to return an
error code, but instead the function continues and will crash on the next
line. Add the missing return statement.
Fixes: 0497236287 ("drm/bridge: Add ITE IT6263 LVDS to HDMI converter")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Liu Ying <victor.liu@nxp.com>
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Link: https://patchwork.freedesktop.org/patch/msgid/804a758b-f2e7-4116-b72d-29bc8905beed@stanley.mountain
After a job completes, the corresponding pointer in the device must
be set to NULL. Failing to do so triggers a warning when unloading
the driver, as it appears the job is still active. To prevent this,
assign the job pointer to NULL after completing the job, indicating
the job has finished.
Fixes: 14d1d19086 ("drm/v3d: Remove the bad signaled() implementation.")
Signed-off-by: Maíra Canal <mcanal@igalia.com>
Reviewed-by: Jose Maria Casanova Crespo <jmcasanova@igalia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250113154741.67520-1-mcanal@igalia.com
Adds a new BO param that keeps the reservation locked after creation.
This removes the need to re-reserve the BO after creation which is a
waste of cycles.
This also fixes a bug in vmw_prime_import_sg_table where the imported
reservation is unlocked twice.
Signed-off-by: Ian Forbes <ian.forbes@broadcom.com>
Fixes: b32233acce ("drm/vmwgfx: Fix prime import/export")
Reviewed-by: Zack Rusin <zack.rusin@broadcom.com>
Signed-off-by: Zack Rusin <zack.rusin@broadcom.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250110185335.15301-1-ian.forbes@broadcom.com
The fence sync logic doesn't handle a fence sync across devices
as it tries to write to a channel offset from one device into
the fence bo from a different device, which won't work so well.
This patch fixes that to avoid using the sync path in the case
where the fences come from different nouveau drm devices.
This works fine on a single device as the fence bo is shared
across the devices, and mapped into each channels vma space,
the channel offsets are therefore okay to pass between sides,
so one channel can sync on the seqnos from the other by using
the offset into it's vma.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Cc: stable@vger.kernel.org
Reviewed-by: Ben Skeggs <bskeggs@nvidia.com>
[ Fix compilation issue; remove version log from commit messsage.
- Danilo ]
Signed-off-by: Danilo Krummrich <dakr@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20250109005553.623947-1-airlied@gmail.com
Extend HDMI connector output format tests to verify its registration
succeeds only when the presence of YUV420 in the supported formats
matches the state of ycbcr_420_allowed flag.
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20241224-bridge-conn-fmt-prio-v4-4-a9ceb5671379@collabora.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Ensure HDMI connector initialization fails when the presence of
HDMI_COLORSPACE_YUV420 in the given supported_formats bitmask doesn't
match the value of drm_connector->ycbcr_420_allowed.
Suggested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20241224-bridge-conn-fmt-prio-v4-3-a9ceb5671379@collabora.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
The case of having an HDMI bridge in the pipeline which advertises
YUV420 capability via its ->supported_formats and a non-HDMI one that
didn't enable ->ycbcr_420_allowed, is incorrectly handled because
supported_formats is passed as is to the helper initializing the HDMI
connector.
Ensure HDMI_COLORSPACE_YUV420 is removed from the bitmask passed to
drmm_connector_hdmi_init() when connector's ->ycbcr_420_allowed flag
ends up not being set.
Fixes: 3ced1c6875 ("drm/display: bridge_connector: handle ycbcr_420_allowed")
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20241224-bridge-conn-fmt-prio-v4-2-a9ceb5671379@collabora.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Bridges having DRM_BRIDGE_OP_HDMI set in their ->ops are supposed to
rely on the ->supported_formats bitmask to advertise the permitted
colorspaces, including HDMI_COLORSPACE_YUV420.
However, a new flag ->ycbcr_420_allowed has been recently introduced,
which brings the necessity to require redundant and potentially
inconsistent information to be provided on HDMI bridges initialization.
Adjust ->ycbcr_420_allowed for HDMI bridges according to
->supported_formats, right before adding them to the global bridge list.
This keeps the initialization process straightforward and unambiguous,
thereby preventing any further confusion.
Fixes: 3ced1c6875 ("drm/display: bridge_connector: handle ycbcr_420_allowed")
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20241224-bridge-conn-fmt-prio-v4-1-a9ceb5671379@collabora.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Macbook 5,1 with MCP79 lost its backlight control since the recent
change for supporting GSP-RM; it rewrote the whole nv50 backlight
control code and each display engine is supposed to have an entry for
IOR bl callback, but it didn't cover mcp77.
This patch adds the missing bl entry initialization for mcp77 display
engine to recover the backlight control.
Fixes: 2274ce7e36 ("drm/nouveau/disp: add output backlight control methods")
Cc: stable@vger.kernel.org
Link: https://bugzilla.suse.com/show_bug.cgi?id=1223838
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Danilo Krummrich <dakr@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20250102114944.11499-1-tiwai@suse.de
Delete one line break to make the format correct, resolving the
following warning during a W=1 build:
>> drivers/gpu/drm/tests/drm_kunit_helpers.c:324: warning: bad line: for a KUnit test
Fixes: caa714f866 ("drm/tests: helpers: Add helper for drm_display_mode_from_cea_vic()")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202501032001.O6WY1VCW-lkp@intel.com/
Reviewed-by: Kuan-Wei Chiu <visitorckw@gmail.com>
Tested-by: Kuan-Wei Chiu <visitorckw@gmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Yu-Chun Lin <eleanor15x@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250104165134.1695864-1-eleanor15x@gmail.com
Signed-off-by: Maxime Ripard <mripard@kernel.org>
The host_node pointer was assigned and freed in adv7533_parse_dt(), and
later, adv7533_attach_dsi() uses the same. Fix this use-after-free issue
by dropping of_node_put() in adv7533_parse_dt() and calling of_node_put()
in error path of probe() and also in the remove().
Fixes: 1e4d58cd7f ("drm/bridge: adv7533: Create a MIPI DSI device")
Cc: stable@vger.kernel.org
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241119192040.152657-2-biju.das.jz@bp.renesas.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
AUDIO_UPDATE bit (Bit 5 of MAIN register 0x4A) needs to be set to 1
while updating Audio InfoFrame information and then set to 0 when done.
Otherwise partially updated Audio InfoFrames could be sent out. Two
cases where this rule were not followed are fixed:
- In adv7511_hdmi_hw_params() make sure AUDIO_UPDATE bit is updated
before/after setting ADV7511_REG_AUDIO_INFOFRAME.
- In audio_startup() use the correct register for clearing
AUDIO_UPDATE bit.
The problem with corrupted audio infoframes were discovered by letting
a HDMI logic analyser check the output of ADV7535.
Note that this patchs replaces writing REG_GC(1) with
REG_INFOFRAME_UPDATE. Bit 5 of REG_GC(1) is positioned within field
GC_PP[3:0] and that field doesn't control audio infoframe and is read-
only. My conclusion therefore was that the author if this code meant to
clear bit 5 of REG_INFOFRAME_UPDATE from the very beginning.
Tested-by: Biju Das <biju.das.jz@bp.renesas.com>
Fixes: 53c515befe ("drm/bridge: adv7511: Add Audio support")
Signed-off-by: Stefan Ekenberg <stefan.ekenberg@axis.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20241119-adv7511-audio-info-frame-v4-1-4ae68e76c89c@axis.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Commit baf4afc583 ("drm/sched: Improve teardown documentation")
added a list of drm_sched_fini()'s problems. The list triggers htmldocs
warning (but renders correctly in htmldocs output):
Documentation/gpu/drm-mm:571: ./drivers/gpu/drm/scheduler/sched_main.c:1359: ERROR: Unexpected indentation.
Separate the list from the preceding paragraph by a blank line to fix
the warning. While at it, also end the aforementioned paragraph by a
colon.
Fixes: baf4afc583 ("drm/sched: Improve teardown documentation")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Closes: https://lore.kernel.org/r/20241108175655.6d3fcfb7@canb.auug.org.au/
Signed-off-by: Bagas Sanjaya <bagasdotme@gmail.com>
[phasta: Adjust commit message]
Signed-off-by: Philipp Stanner <phasta@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20241217034915.62594-1-bagasdotme@gmail.com
Move pm_runtime_set_active() to ivpu_pm_init() so when
ivpu_ipc_send_receive_internal() is executed before ivpu_pm_enable()
it already has correct runtime state, even if last resume was
not successful.
Fixes: 8ed520ff46 ("accel/ivpu: Move set autosuspend delay to HW specific code")
Cc: stable@vger.kernel.org # v6.7+
Reviewed-by: Karol Wachowski <karol.wachowski@intel.com>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Signed-off-by: Jacek Lawrynowicz <jacek.lawrynowicz@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241210130939.1575610-4-jacek.lawrynowicz@linux.intel.com
Add appropriate error handling to ensure all allocated resources are
released upon encountering an error.
Fixes: a74f4d9913 ("accel/ivpu: Defer MMU root page table allocation")
Cc: Karol Wachowski <karol.wachowski@intel.com>
Reviewed-by: Karol Wachowski <karol.wachowski@intel.com>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Signed-off-by: Jacek Lawrynowicz <jacek.lawrynowicz@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241210130939.1575610-3-jacek.lawrynowicz@linux.intel.com
The 'select FB_CORE' statement moved from CONFIG_DRM to DRM_CLIENT_LIB,
but there are now configurations that have code calling into fb_core
as built-in even though the client_lib itself is a loadable module:
x86_64-linux-ld: drivers/gpu/drm/drm_fb_helper.o: in function `drm_fb_helper_set_suspend':
drm_fb_helper.c:(.text+0x2c6): undefined reference to `fb_set_suspend'
x86_64-linux-ld: drivers/gpu/drm/drm_fb_helper.o: in function `drm_fb_helper_resume_worker':
drm_fb_helper.c:(.text+0x2e1): undefined reference to `fb_set_suspend'
In addition to DRM_CLIENT_LIB, the 'select' needs to be at least in
DRM_KMS_HELPER and DRM_GEM_SHMEM_HELPER, so add it here.
This patch is the KMS_HELPER part of [1].
Fixes: dadd28d414 ("drm/client: Add client-lib module")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/series/141411/ # 1
Link: https://patchwork.freedesktop.org/patch/msgid/20241216074450.8590-4-tzimmermann@suse.de
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Do not select BACKLIGHT_CLASS_DEVICE from FB_BACKLIGHT. The latter
only controls backlight support within fbdev core code and data
structures.
Make fbdev drivers depend on BACKLIGHT_CLASS_DEVICE and let users
select it explicitly. Fixes warnings about recursive dependencies,
such as
error: recursive dependency detected!
symbol BACKLIGHT_CLASS_DEVICE is selected by FB_BACKLIGHT
symbol FB_BACKLIGHT is selected by FB_SH_MOBILE_LCDC
symbol FB_SH_MOBILE_LCDC depends on FB_DEVICE
symbol FB_DEVICE depends on FB_CORE
symbol FB_CORE is selected by DRM_GEM_DMA_HELPER
symbol DRM_GEM_DMA_HELPER is selected by DRM_PANEL_ILITEK_ILI9341
symbol DRM_PANEL_ILITEK_ILI9341 depends on BACKLIGHT_CLASS_DEVICE
BACKLIGHT_CLASS_DEVICE is user-selectable, so making drivers adapt to
it is the correct approach in any case. For most drivers, backlight
support is also configurable separately.
v3:
- Select BACKLIGHT_CLASS_DEVICE in PowerMac defconfigs (Christophe)
- Fix PMAC_BACKLIGHT module dependency corner cases (Christophe)
v2:
- s/BACKLIGHT_DEVICE_CLASS/BACKLIGHT_CLASS_DEVICE (Helge)
- Fix fbdev driver-dependency corner case (Arnd)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20241216074450.8590-2-tzimmermann@suse.de
Instead of returning a generic NULL on error from
drm_dp_tunnel_mgr_create(), use error pointers with informative codes
to align the function with stub that is executed when
CONFIG_DRM_DISPLAY_DP_TUNNEL is unset. This will also trigger IS_ERR()
in current caller (intel_dp_tunnerl_mgr_init()) instead of bypassing it
via NULL pointer.
v2: use error codes inside drm_dp_tunnel_mgr_create() instead of handling
on caller's side (Michal, Imre)
v3: fixup commit message and add "CC"/"Fixes" lines (Andi),
mention aligning function code with stub
Fixes: 91888b5b1a ("drm/i915/dp: Add support for DP tunnel BW allocation")
Cc: Imre Deak <imre.deak@intel.com>
Cc: <stable@vger.kernel.org> # v6.9+
Signed-off-by: Krzysztof Karas <krzysztof.karas@intel.com>
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/7q4fpnmmztmchczjewgm6igy55qt6jsm7tfd4fl4ucfq6yg2oy@q4lxtsu6445c
The shutdown function can be called when the display is already
unprepared. For example during reboot this trigger a kernel
backlog. Calling the drm_panel_unprepare, allow us to avoid
to trigger the kernel warning.
Fixes: 2e87bad7cd ("drm/panel: Add Synaptics R63353 panel driver")
Tested-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Jessica Zhang <quic_jesszhan@quicinc.com>
Link: https://lore.kernel.org/r/20241205163002.1804784-1-dario.binacchi@amarulasolutions.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20241205163002.1804784-1-dario.binacchi@amarulasolutions.com
The arguments for __dma_buf_debugfs_list_del do not match for both the
CONFIG_DEBUG_FS case and the !CONFIG_DEBUG_FS case. The !CONFIG_DEBUG_FS
case should take a struct dma_buf *, but it's currently struct file *.
This can lead to the build error:
error: passing argument 1 of ‘__dma_buf_debugfs_list_del’ from
incompatible pointer type [-Werror=incompatible-pointer-types]
dma-buf.c:63:53: note: expected ‘struct file *’ but argument is of
type ‘struct dma_buf *’
63 | static void __dma_buf_debugfs_list_del(struct file *file)
Fixes: bfc7bc5393 ("dma-buf: Do not build debugfs related code when !CONFIG_DEBUG_FS")
Signed-off-by: T.J. Mercier <tjmercier@google.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@igalia.com>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20241117170326.1971113-1-tjmercier@google.com
In export_udmabuf(), if dma_buf_fd() fails because the FD table is full, a
dma_buf owning the udmabuf has already been created; but the error handling
in udmabuf_create() will tear down the udmabuf without doing anything about
the containing dma_buf.
This leaves a dma_buf in memory that contains a dangling pointer; though
that doesn't seem to lead to anything bad except a memory leak.
Fix it by moving the dma_buf_fd() call out of export_udmabuf() so that we
can give it different error handling.
Note that the shape of this code changed a lot in commit 5e72b2b41a
("udmabuf: convert udmabuf driver to use folios"); but the memory leak
seems to have existed since the introduction of udmabuf.
Fixes: fbb0de7950 ("Add udmabuf misc device")
Acked-by: Vivek Kasireddy <vivek.kasireddy@intel.com>
Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: Vivek Kasireddy <vivek.kasireddy@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241204-udmabuf-fixes-v2-3-23887289de1c@google.com
When F_SEAL_FUTURE_WRITE was introduced, it was overlooked that udmabuf
must reject memfds with this flag, just like ones with F_SEAL_WRITE.
Fix it by adding F_SEAL_FUTURE_WRITE to SEALS_DENIED.
Fixes: ab3948f58f ("mm/memfd: add an F_SEAL_FUTURE_WRITE seal to memfd")
Cc: stable@vger.kernel.org
Acked-by: Vivek Kasireddy <vivek.kasireddy@intel.com>
Signed-off-by: Jann Horn <jannh@google.com>
Reviewed-by: Joel Fernandes (Google) <joel@joelfernandes.org>
Signed-off-by: Vivek Kasireddy <vivek.kasireddy@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241204-udmabuf-fixes-v2-2-23887289de1c@google.com
Some entries use my kernel.org address, while others use my Red Hat one.
Since this is a bit of an inconvinience for me, align them to all use the
same (kernel.org) address.
Acked-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Danilo Krummrich <dakr@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20241204152248.8644-1-dakr@kernel.org
The 'select FB_CORE' statement moved from CONFIG_DRM to DRM_CLIENT_LIB,
but there are now configurations that have code calling into fb_core
as built-in even though the client_lib itself is a loadable module:
x86_64-linux-ld: drivers/gpu/drm/drm_fbdev_shmem.o: in function `drm_fbdev_shmem_driver_fbdev_probe':
drm_fbdev_shmem.c:(.text+0x1fc): undefined reference to `fb_deferred_io_init'
x86_64-linux-ld: drivers/gpu/drm/drm_fbdev_shmem.o: in function `drm_fbdev_shmem_fb_destroy':
drm_fbdev_shmem.c:(.text+0x2e1): undefined reference to `fb_deferred_io_cleanup'
In addition to DRM_CLIENT_LIB, the 'select' needs to be at least in
two more parts, DRM_KMS_HELPER and DRM_GEM_SHMEM_HELPER, so add those
here.
v3:
- Remove FB_CORE from DRM_KMS_HELPER to avoid circular dependency
Fixes: dadd28d414 ("drm/client: Add client-lib module")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20241115162323.3555229-1-arnd@kernel.org
On the Raspberry Pi 5, performance counters are not being cleared
when `v3d_perfmon_start()` is called, even though we write to the
CLR register. As a result, their values accumulate until they
overflow.
The expected behavior is for performance counters to reset to zero
at the start of a job. When the job finishes and the perfmon is
stopped, the counters should accurately reflect the values for that
specific job.
To ensure this behavior, the performance counters are now enabled
before being cleared. This allows the CLR register to function as
intended, zeroing the counter values when the job begins.
Fixes: 26a4dc29b7 ("drm/v3d: Expose performance counters to userspace")
Signed-off-by: Maíra Canal <mcanal@igalia.com>
Reviewed-by: Iago Toral Quiroga <itoral@igalia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241204122831.17015-1-mcanal@igalia.com
After an out-of-memory error the reception state should be reset, so
that the next attempt receiving a message doesn't fail (due to getting a
start-of-message packet, while the reception state has already the
start-of-message flag set).
Cc: Lyude Paul <lyude@redhat.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241203160223.2926014-7-imre.deak@intel.com
While receiving an MST up request message from one thread in
drm_dp_mst_handle_up_req(), the MST topology could be removed from
another thread via drm_dp_mst_topology_mgr_set_mst(false), freeing
mst_primary and setting drm_dp_mst_topology_mgr::mst_primary to NULL.
This could lead to a NULL deref/use-after-free of mst_primary in
drm_dp_mst_handle_up_req().
Avoid the above by holding a reference for mst_primary in
drm_dp_mst_handle_up_req() while it's used.
v2: Fix kfreeing the request if getting an mst_primary reference fails.
Cc: Lyude Paul <lyude@redhat.com>
Reviewed-by: Lyude Paul <lyude@redhat.com> (v1)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241204132007.3132494-1-imre.deak@intel.com
If receiving a reply for an MST down request message times out, the
thread receiving the reply in drm_dp_mst_handle_down_rep() could try to
dereference the drm_dp_sideband_msg_tx txmsg request message after the
thread waiting for the reply - calling drm_dp_mst_wait_tx_reply() - has
timed out and freed txmsg, hence leading to a use-after-free in
drm_dp_mst_handle_down_rep().
Prevent the above by holding the drm_dp_mst_topology_mgr::qlock in
drm_dp_mst_handle_down_rep() for the whole duration txmsg is looked up
from the request list and dereferenced.
v2: Fix unlocking mgr->qlock after verify_rx_request_type() fails.
Cc: Lyude Paul <lyude@redhat.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241203174632.2941402-1-imre.deak@intel.com
Simplify the error return path in drm_dp_mst_handle_down_rep(),
preparing for the next patch.
While at it use reset_msg_rx_state() instead of open-coding it.
Cc: Lyude Paul <lyude@redhat.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241203160223.2926014-4-imre.deak@intel.com
