On MTL the GOP (for whatever reason) likes to bind its framebuffer
high up in the ggtt address space. This can conflict with whatever
ggtt_reserve_guc_top() is trying to do, and the result is that
ggtt_reserve_guc_top() fails and then we proceed to explode when
trying to tear down the driver. Thus far I haven't analyzed what
causes the actual fireworks, but it's not super important as even
if it didn't explode we'd still fail the driver load and the user
would be left with an unusable GPU.
To remedy this (without having to figure out exactly what
ggtt_reserve_guc_top() is trying to achieve) we can attempt to
relocate the BIOS framebuffer to a lower ggtt address. We can do
this at this early point in driver init because nothing else is
supposed to be clobbering the ggtt yet. So we simply change where
in the ggtt we pin the vma, the original PTEs will be left as is,
and the new PTEs will get written with the same dma addresses.
The plane will keep on scanning out from the original PTEs until
we are done with the whole process, and at that point we rewrite
the plane's surface address register to point at the new ggtt
address.
Since we don't need a specific ggtt address for the plane
(apart from needing it to land in the mappable region for
normal stolen objects) we'll just try to pin it without a fixed
offset first. It should end up at the lowest available address
(which really should be 0 at this point in the driver init).
If that fails we'll fall back to just pinning it exactly to the
origianal address.
To make sure we don't accidentlally pin it partially over the
original ggtt range (as that would corrupt the original PTEs)
we reserve the original range temporarily during this process.
v2: Try to pin explicitly to ggtt offset 0 as otherwise DG2 puts it
even higher (atm we have no PIN_LOW flag to force it low)
v3: "fix" xe
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Tested-by: Paz Zcharya <pazz@chromium.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240202224340.30647-16-ville.syrjala@linux.intel.com
Acked-by: Lucas De Marchi <lucas.demarchi@intel.com>
Pull all the state swap stuff into its own function to declutter
intel_atomic_commit() a bit.
Note that currently the state swap is spread across both
sides of the unprepare branch in intel_atomic_commit(), but
we can pull all of it ahead a bit since we bail on the first
error, and thus there is no change in behaviour from the
reordering.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231219130756.25986-4-ville.syrjala@linux.intel.com
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Instead of injecting extra crtc commits to serialize the global
state let's hand roll a bit of commit machinery to take care of
the hardware synchronization.
Rather than basing everything on the crtc commits we track these
as their own thing. I think this makes more sense as the hardware
blocks we are working with are not in any way tied to the pipes,
so the completion should not be tied in with the vblank machinery
either.
The difference to the old behaviour is that:
- we no longer pull extra crtcs into the commit which should
make drm_atomic_check_only() happier
- since those crtcs don't get pulled in we also don't end up
reprogamming them and thus don't need to wait their vblanks
to pass/etc. So this should be tad faster as well.
TODO: perhaps have each global object complete its own commit
once the post-plane update phase is done?
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/6728
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231219130756.25986-3-ville.syrjala@linux.intel.com
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
There is a new register used to configure selective update area size
for early transport.
Configure PIPE_SRCSZ_ERLY_TPT using calculated selective update area
carried in crtc_state->su_area.
Bspec: 68927
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231218175004.52875-6-jouni.hogander@intel.com
An unexpected modeset or connector detection by a user (user space or FB
console) during the initialization/shutdown sequence is possible either
via a hotplug IRQ handling work or via the connector sysfs
(status/detect) interface. These modesets/detections should be prevented
by disabling/flushing all related hotplug handling work and
unregistering the interfaces that can start them at the beginning of the
shutdown sequence. Some of this - disabling all related intel_hotplug
work - will be done by the next patch, but others - for instance
disabling the MST hotplug works - require a bigger rework.
It makes sense - for diagnostic purpose, even with all the above work and
interface disabled - to detect and reject any such user access. This
patch does that for modeset accesses and a follow-up patch for connector
detection.
During driver loading/unloading/system suspend/shutdown and during
system resume after calling intel_display_driver_disable_user_access()
or intel_display_driver_resume_access() correspondigly, the current
thread is allowed to modeset (as this thread requires to do an
initial/restoring modeset or a disabling modeset), other threads (the
user threads) are not allowed to modeset.
During driver loading/system resume after calling
intel_display_driver_enable_user_access() all threads are allowed to
modeset.
During driver unloading/system suspend/shutdown after calling
intel_display_driver_suspend_access() no threads are allowed to modeset
(as the HW got disabled and should stay in this state).
v2: Call intel_display_driver_suspend_access()/resume_access() only
for HAS_DISPLAY(). (CI)
v3: (Jouni)
- Add commit log comments explaining how the permission of modeset
changes during HW init/deinit wrt. to the current and other user
processes.
Link: https://patchwork.freedesktop.org/patch/msgid/20240104132335.2766434-1-imre.deak@intel.com
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Pipe config check is currently ignoring vsc sdp changes completely
if psr is enabled. We want to ignore only PSR part of it as there
might be changes in colorimetry data. Also read back vsc_sdp when psr is
used.
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Tested-by: Shawn Lee <shawn.c.lee@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231220103609.1384523-6-jouni.hogander@intel.com
After switching to directly using dma_fence instead of i915_sw_fence we
have left some dead code around intel_atomic_helper->free_list. Remove that
dead code.
v2: Remove intel_atomic_state->freed as well
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231114134141.2527694-1-jouni.hogander@intel.com
Currently we get bigjoiner config after the dsc get config, during HW
readout.
Since dsc_get_config now uses bigjoiner flags/pipes to compute DSC PPS
parameter pic_width, this results in a state mismatch when Bigjoiner
and DSC are used together.
So call get bigjoiner config before calling dsc get config function.
Fixes: 8b70b56917 ("drm/i915/vdsc: Fill the intel_dsc_get_pps_config function")
Cc: Suraj Kandpal <suraj.kandpal@intel.com>
Cc: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Cc: Animesh Manna <animesh.manna@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Suraj Kandpal <suraj.kandpal@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231122064627.905828-1-ankit.k.nautiyal@intel.com
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmV2PMQeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGhgQIAKSdjtpkv+IeDwph
umLHxDlCTT8nl+TAhEYuxSdMiHt1i7+zyF0snnHhGthBRnBZBf+PDdkQOmqtjLZj
e591VGY7tdNCAVUwmRRaI82JFz9Pl1k8DXL3f+CE1+MfbpsirAecoIAL0rsvg+4f
ICKSAOBZonL7GT7IGrsbxgqGKCLC+2PcgNT4pADBdjtbC1nmVSLK21dtWr6i4xsn
CT9MxAnej1+EOpreyHhNZUVqfQy0/04x4OY0u/EOXU3PgpfGTrAzkyfwzcd/eit0
x59TZ0owDVXfvvdXUUAC0zG1th2ek5LKNtL+C4rKOoAbq7GZoQfjN5M/Ug+yykwE
aqm6CJ8=
=tZ+R
-----END PGP SIGNATURE-----
Backmerge tag 'v6.7-rc5' into drm-next
Linux 6.7-rc5
Alex requested this for some amdkfd work relying on the symbols exports.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Invoke drm_plane_helper_funcs.end_fb_access before
drm_atomic_helper_commit_hw_done(). The latter function hands over
ownership of the plane state to the following commit, which might
free it. Releasing resources in end_fb_access then operates on undefined
state. This bug has been observed with non-blocking commits when they
are being queued up quickly.
Here is an example stack trace from the bug report. The plane state has
been free'd already, so the pages for drm_gem_fb_vunmap() are gone.
Unable to handle kernel paging request at virtual address 0000000100000049
[...]
drm_gem_fb_vunmap+0x18/0x74
drm_gem_end_shadow_fb_access+0x1c/0x2c
drm_atomic_helper_cleanup_planes+0x58/0xd8
drm_atomic_helper_commit_tail+0x90/0xa0
commit_tail+0x15c/0x188
commit_work+0x14/0x20
Fix this by running end_fb_access immediately after updating all planes
in drm_atomic_helper_commit_planes(). The existing clean-up helper
drm_atomic_helper_cleanup_planes() now only handles cleanup_fb.
For aborted commits, roll back from drm_atomic_helper_prepare_planes()
in the new helper drm_atomic_helper_unprepare_planes(). This case is
different from regular cleanup, as we have to release the new state;
regular cleanup releases the old state. The new helper also invokes
cleanup_fb for all planes.
The changes mostly involve DRM's atomic helpers. Only two drivers, i915
and nouveau, implement their own commit function. Update them to invoke
drm_atomic_helper_unprepare_planes(). Drivers with custom commit_tail
function do not require changes.
v4:
* fix documentation (kernel test robot)
v3:
* add drm_atomic_helper_unprepare_planes() for rolling back
* use correct state for end_fb_access
v2:
* fix test in drm_atomic_helper_cleanup_planes()
Reported-by: Alyssa Ross <hi@alyssa.is>
Closes: https://lore.kernel.org/dri-devel/87leazm0ya.fsf@alyssa.is/
Suggested-by: Daniel Vetter <daniel@ffwll.ch>
Fixes: 94d879eaf7 ("drm/atomic-helper: Add {begin,end}_fb_access to plane helpers")
Tested-by: Alyssa Ross <hi@alyssa.is>
Reviewed-by: Alyssa Ross <hi@alyssa.is>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Cc: <stable@vger.kernel.org> # v6.2+
Link: https://patchwork.freedesktop.org/patch/msgid/20231204083247.22006-1-tzimmermann@suse.de
Apparently some BXT/GLK systems have DSI panels whose timings
don't agree with the normal cpu transcoder hblank>=32 limitation.
This is perhaps fine as there are no specific hblank/etc. limits
listed for the BXT/GLK DSI transcoders.
Move those checks out from the global intel_mode_valid() into
into connector specific .mode_valid() hooks, skipping BXT/GLK
DSI connectors. We'll leave the basic [hv]display/[hv]total
checks in intel_mode_valid() as those seem like sensible upper
limits regardless of the transcoder used.
Cc: stable@vger.kernel.org
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/9720
Fixes: 8f4b1068e7 ("drm/i915: Check some transcoder timing minimum limits")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231127145028.4899-1-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
(cherry picked from commit e0ef2daa8c)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
{planes,vrr}_{enabling,disabling}() are supposed to indicate
whether the specific hardware feature is supposed to be enabling
or disabling. That can only makes sense if the pipe is active
overall. So check for that before we go poking at the hardware.
I think we're semi-safe currently on due to:
- intel_pre_plane_update() doesn't get called when the pipe
was not-active prior to the commit, but this is actually a bug.
This saves vrr_disabling(), and vrr_enabling() is called from
deeper down where we have already checked hw.active.
- active_planes mirrors the crtc's hw.active
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231121054324.9988-2-ville.syrjala@linux.intel.com
(cherry picked from commit bc53c4d56e)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Use the >= and < operators for the DISPLAY_VER checks everywhere.
This is what most of the code does, but especially recently random
pieces of code have started doing this differently for no good reason.
Conversion done with the following cocci:
@find@
expression i915;
constant ver;
@@
(
DISPLAY_VER(i915) <= ver
|
DISPLAY_VER(i915) > ver
)
@script:python inc@
old_ver << find.ver;
new_ver;
@@
coccinelle.new_ver = str(int(old_ver) + 1)
@@
expression find.i915;
constant find.ver;
identifier inc.new_ver;
@@
(
- DISPLAY_VER(i915) <= ver
+ DISPLAY_VER(i915) < new_ver
|
- DISPLAY_VER(i915) > ver
+ DISPLAY_VER(i915) >= new_ver
)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231127145028.4899-4-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Apparently some BXT/GLK systems have DSI panels whose timings
don't agree with the normal cpu transcoder hblank>=32 limitation.
This is perhaps fine as there are no specific hblank/etc. limits
listed for the BXT/GLK DSI transcoders.
Move those checks out from the global intel_mode_valid() into
into connector specific .mode_valid() hooks, skipping BXT/GLK
DSI connectors. We'll leave the basic [hv]display/[hv]total
checks in intel_mode_valid() as those seem like sensible upper
limits regardless of the transcoder used.
Cc: stable@vger.kernel.org
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/9720
Fixes: 8f4b1068e7 ("drm/i915: Check some transcoder timing minimum limits")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231127145028.4899-1-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
We used to call intel_pre_plane_updates() for any pipe going through
a modeset whether the pipe was previously enabled or not. This in
fact needed to apply all the necessary clock gating workarounds/etc.
Restore the correct behaviour.
Fixes: 3991999732 ("drm/i915: Disable all planes before modesetting any pipes")
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231121054324.9988-3-ville.syrjala@linux.intel.com
(cherry picked from commit e0d5ce11ed)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
There's no real reason why we'd need a full modeset for audio
changes. So let's allow audio to be toggled during fastset.
In case the ELD changes while has_audio isn't changing state
we force both audio disable and enable so the new ELD gets
propagated to the audio driver.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231121054324.9988-12-ville.syrjala@linux.intel.com
We used to call intel_pre_plane_updates() for any pipe going through
a modeset whether the pipe was previously enabled or not. This in
fact needed to apply all the necessary clock gating workarounds/etc.
Restore the correct behaviour.
Fixes: 3991999732 ("drm/i915: Disable all planes before modesetting any pipes")
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231121054324.9988-3-ville.syrjala@linux.intel.com
{planes,vrr}_{enabling,disabling}() are supposed to indicate
whether the specific hardware feature is supposed to be enabling
or disabling. That can only makes sense if the pipe is active
overall. So check for that before we go poking at the hardware.
I think we're semi-safe currently on due to:
- intel_pre_plane_update() doesn't get called when the pipe
was not-active prior to the commit, but this is actually a bug.
This saves vrr_disabling(), and vrr_enabling() is called from
deeper down where we have already checked hw.active.
- active_planes mirrors the crtc's hw.active
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231121054324.9988-2-ville.syrjala@linux.intel.com
Reuse intel_dp_max_data_rate() and intel_dp_effective_data_rate() in
intel_link_compute_m_n(), instead of open-coding the equivalent. Note
the kbit/sec -> kByte/sec unit change in the M/N values, but this not
reducing the precision, as the link rate value is based anyway on a less
precise 10 kbit/sec value.
Suggested-by: Jani Nikula <jani.nikula@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231116131841.1588781-12-imre.deak@intel.com
The link M/N ratio is the data rate / link symbol clock rate, fix things
up accordingly. On DP 1.4 this ratio was correct as the link symbol clock
rate in that case matched the link data rate (in bytes/sec units, the
symbol size being 8 bits), however it wasn't correct for UHBR rates
where the symbol size is 32 bits.
Kudos to Arun noticing in Bspec the incorrect use of link data rate in
the ratio's N value.
Reviewed-by: Arun R Murthy <arun.r.murthy@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231116131841.1588781-7-imre.deak@intel.com
Considering what the functions do, intel_dpll.c is a more suitable
location, and lets us make some functions static while at it.
This also means intel_display.c no longer does any DPIO access.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231114104534.4180144-1-jani.nikula@intel.com
MTL+ supports fractional compressed bits_per_pixel, with precision of
1/16. This compressed bpp is stored in U6.4 format.
Accommodate this precision while computing m_n values.
v1:
Replace the computation of 'data_clock' with 'data_clock =
DIV_ROUND_UP(data_clock, 16).' (Sui Jingfeng).
v2:
Rebase and pass bits_per_pixel in U6.4 format.
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Mitul Golani <mitulkumar.ajitkumar.golani@intel.com>
Reviewed-by: Suraj Kandpal <suraj.kandpal@intel.com>
Reviewed-by: Sui Jingfeng <suijingfeng@loongson.cn>
Link: https://patchwork.freedesktop.org/patch/msgid/20231110101020.4067342-4-ankit.k.nautiyal@intel.com
DSC parameter bits_per_pixel is stored in U6.4 format.
The 4 bits represent the fractional part of the bpp.
Currently we use compressed_bpp member of dsc structure to store
only the integral part of the bits_per_pixel.
To store the full bits_per_pixel along with the fractional part,
compressed_bpp is changed to store bpp in U6.4 formats. Intergral
part is retrieved by simply right shifting the member compressed_bpp by 4.
v2:
-Use to_bpp_int, to_bpp_frac_dec, to_bpp_x16 helpers while dealing
with compressed bpp. (Suraj)
-Fix comment styling. (Suraj)
v3:
-Add separate file for 6.4 fixed point helper(Jani, Nikula)
-Add comment for magic values(Suraj)
v4:
-Fix checkpatch warnings caused by renaming(Suraj)
v5:
-Rebase.
-Use existing helpers for conversion of bpp_int to bpp_x16
and vice versa.
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Mitul Golani <mitulkumar.ajitkumar.golani@intel.com>
Reviewed-by: Suraj Kandpal <suraj.kandpal@intel.com>
Reviewed-by: Sui Jingfeng <suijingfeng@loongson.cn>
Link: https://patchwork.freedesktop.org/patch/msgid/20231110101020.4067342-3-ankit.k.nautiyal@intel.com
Perform all the intel_pre_update_crtc() stuff for all pipes first,
and only then do the intel_update_crtc() vblank evasion stuff for
every pipe back to back. This should make it more likely that
the plane updates from multiple pipes happen on the same frame
(assuming the pipes are running in sync, eg. due to bigjoiner
or port sync).
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230907122541.32261-4-ville.syrjala@linux.intel.com
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Split intel_update_crtc() into two parts such that the first
part performs all the non-vblank evasion preparatory stuff,
and the second part just does the vblank evasion stuff.
For now we just call these back to back so that there is
no funcitonal change.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230907122541.32261-3-ville.syrjala@linux.intel.com
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Since commit 7de5b6b546 ("drm/i915: Don't flag both full
modeset and fastset at the same time")
intel_crtc_needs_fastset() and intel_crtc_needs_modeset() have
been mutually exclusive. Drop the redundant check.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230907122541.32261-2-ville.syrjala@linux.intel.com
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
At the moment modesetting a stream CRTC will fail if the stream's BW
along with the current BW of all the other streams on the same MST link
is above the total BW of the MST link. Make the BW sharing more dynamic
by trying to reduce the link bpp of one or more streams on the MST link
in this case.
When selecting a stream to reduce the BW for, take into account which
link segment in the MST topology ran out of BW and which streams go
through this link segment. For instance with A,B,C streams in the same
MST topology A and B may share the BW of a link segment downstream of a
branch device, stream C not downstream of the branch device, hence not
affecting this BW. If this link segment's BW runs out one or both of
stream A/B's BW will be reduced until their total BW is within limits.
While reducing the link bpp for a given stream DSC may need to be
enabled for it, which requires FEC on the whole MST link. Check for this
condition and recompute the state for all streams taking the FEC
overhead into account (on 8b/10b links).
v2:
- Rebase on s/min_bpp_pipes/min_bpp_reached_pipes/ change.
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231030155843.2251023-29-imre.deak@intel.com
Enabling / disabling DSC decompression in the branch device downstream
of the source may reset the whole branch device. To avoid this while the
streams are still active, force a modeset on all CRTC/ports connected to
this branch device.
v2:
- Check the CRTC state for each connector in the topology, instead of
the CRTC being checked for a modeset requirement. (Ville)
- Add DocBook for the new function.
v3:
- Rebased on a change not to use
intel_modeset_pipes_in_mask_early().
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com> (v1)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231107001505.3370108-8-imre.deak@intel.com
Factor out a helper to clear the pipe update flags, used by a follow-up
patch to modeset an MST topology.
v2:
- Move the intel_crtc_needs_modeset() check to the callers. (Ville)
v3 (Ville):
- Rename clear_pipe_update_flags_on_modeset_crtc() to
intel_crtc_flag_modeset().
- Also set crtc_state->uapi.mode_changed in the function.
- Leave out the unrelated change to use
intel_modeset_pipes_in_mask_early().
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com> (v1)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231107001505.3370108-7-imre.deak@intel.com
A follow-up MST patch will need to specify the total BW allocation
overhead, prepare for that here by passing the amount of overhead
to intel_link_compute_m_n(), keeping the existing behavior.
v2:
- Fix passing the correct crtc_state->fec_enable param in
intel_dp_mst_compute_link_config() /
intel_dp_dsc_mst_compute_link_config().
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com> (v1)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231030155843.2251023-13-imre.deak@intel.com
We are preparing for Xe driver. Xe driver doesn't have i915_sw_fence
implementation. Lets drop i915_sw_fence usage from display code and
use dma_fence interfaces directly.
For this purpose stack dma fences from related objects into new plane
state. Drm_gem_plane_helper_prepare_fb can be used for fences in new
fb. Separate local implementation is used for Stacking fences from old fb
into new plane state. Then wait for these stacked fences during atomic
commit. There is no be need for separate GPU reset handling in
intel_atomic_commit_fence_wait as the fences are signaled when GPU hang is
detected and GPU is being reset.
v4:
- Drop to_new_plane_state suffix from add_dma_resv_fences
- Use dma_resv_usage_rw(false) (DMA_RESV_USAGE_WRITE)
v3:
- Rename add_fences and it's parameters
- Remove signaled check
- Remove waiting old_plane_state fences
v2:
- Add fences from old fb into new_plane_state->uapi.fence rather than
into old_plane_state->uapi.fence
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231031084557.1181630-1-jouni.hogander@intel.com
The DP modeset sequence asks us to disable TRANSCONF before clearing
the FECSTALL_DIS_DPTSTREAM_DPTTG bit, although we are still asked
to wait for the transcoder to stop only after both steps have
been done.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231018154123.5479-2-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
With MTL adding PICA between the port and the real phy, the path
add for DG2 stopped being followed and newer platforms are simply using
the older path for TC phys. LNL is no different than MTL in this aspect,
so just add it to the mess. In future the phy and port designation and
deciding if it's TC should better be cleaned up.
To make it just a bit better, also change intel_phy_is_snps() to show
this is DG2-only.
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Gustavo Sousa <gustavo.sousa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231026184045.1015655-3-lucas.demarchi@intel.com
By default fastboot is enabled on all Display 9+ platforms and disabled
on older platforms. Its not necessary to retain this as a module
parameter.
Signed-off-by: Arun R Murthy <arun.r.murthy@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230926091157.635438-1-arun.r.murthy@intel.com
